- use ifp instead if &ac->ac_if in a couple of nd6* calls;
this removes a useless dependency.
- use IFP2AC(ifp) instead of an extra variable to point to the struct arpcom;
this does not remove the nesting dependency between arpcom and ifnet but
makes it more evident.
there so there are no ABI changes);
+ replace 5 redefinitions of the IPF2AC macro with one in if_arp.h
Eventually (but before freezing the ABI) we need to get rid of
struct arpcom (initially with the help of some smart #defines
to avoid having to touch each and every driver, see below).
Apart from the struct ifnet, struct arpcom now only stores a copy
of the MAC address (ac_enaddr, but we already have another copy in
the struct ifnet -- if_addrhead), and a netgraph-specific field
which is _always_ accessed through the ifp, so it might well go
into the struct ifnet too (where, besides, there is already an entry
for AF_NETGRAPH data...)
Too bad ac_enaddr is widely referenced by all drivers. But
this can be fixed as follows:
#define ac_enaddr ac_if.the_original_ac_enaddr_in_struct_ifnet
(note that the right hand side would likely be a pointer rather than
the base address of an array.)
Short description of ip_fastforward:
o adds full direct process-to-completion IPv4 forwarding code
o handles ip fragmentation incl. hw support (ip_flow did not)
o sends icmp needfrag to source if DF is set (ip_flow did not)
o supports ipfw and ipfilter (ip_flow did not)
o supports divert, ipfw fwd and ipfilter nat (ip_flow did not)
o returns anything it can't handle back to normal ip_input
Enable with sysctl -w net.inet.ip.fastforwarding=1
Reviewed by: sam (mentor)
- Support IFF_MONITOR.
- Borrow some consistency for if_input() routines from if_ethersubr.c.
- Correct comments regarding fddi_input() that no longer apply.
drain routines are done by swi_net, which allows for better queue control
at some future point. Packets may also be directly dispatched to a netisr
instead of queued, this may be of interest at some installations, but
currently defaults to off.
Reviewed by: hsu, silby, jayanth, sam
Sponsored by: DARPA, NAI Labs
o on input don't strip the Ethernet header from packets
o input packet handling is now done with if_input
o track changes to ether_ifattach/ether_ifdetach API
o track changes to bpf tapping
o call ether_ioctl for default handling of ioctl's
o use constants from net/ethernet.h where possible
Reviewed by: many
Approved by: re
transmission checks; when it is received, label the packet appropriately.
Although we don't have a local FDDI setup to test this with, the
labeling and checks are identical to other interface classes.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
- Make sure the interface is UP and RUNNING in fddi_input().
- Reorder and comment packet tests in fddi_input().
- Call if_attach() in fddi_ifattach().
- Test for a valid return from ifaddr_byindex().
- Use struct fddi_header where appropriate.
- Use bcopy() rather than memcpy().
- Use FDDI_ADDR_LEN macro instead of ETHER_ADDR_LEN macro.
- Add loadable module support.
- Use FDDI_ADDR_LEN rather than a magic number or a sizeof().
- Hide distracting sizeof() behind FDDI_HDR_LEN macro.
- Don't use sizeof(struct llc) in areas where we mean LLC_SNAPFRAMELEN.
not removing tabs before "__P((", and not outdenting continuation lines
to preserve non-KNF lining up of code with parentheses. Switch to KNF
formatting and/or rewrap the whole prototype in some cases.
This is because calls with M_WAIT (now M_TRYWAIT) may not wait
forever when nothing is available for allocation, and may end up
returning NULL. Hopefully we now communicate more of the right thing
to developers and make it very clear that it's necessary to check whether
calls with M_(TRY)WAIT also resulted in a failed allocation.
M_TRYWAIT basically means "try harder, block if necessary, but don't
necessarily wait forever." The time spent blocking is tunable with
the kern.ipc.mbuf_wait sysctl.
M_WAIT is now deprecated but still defined for the next little while.
* Fix a typo in a comment in mbuf.h
* Fix some code that was actually passing the mbuf subsystem's M_WAIT to
malloc(). Made it pass M_WAITOK instead. If we were ever to redefine the
value of the M_WAIT flag, this could have became a big problem.
before adding/removing packets from the queue. Also, the if_obytes and
if_omcasts fields should only be manipulated under protection of the mutex.
IF_ENQUEUE, IF_PREPEND, and IF_DEQUEUE perform all necessary locking on
the queue. An IF_LOCK macro is provided, as well as the old (mutex-less)
versions of the macros in the form _IF_ENQUEUE, _IF_QFULL, for code which
needs them, but their use is discouraged.
Two new macros are introduced: IF_DRAIN() to drain a queue, and IF_HANDOFF,
which takes care of locking/enqueue, and also statistics updating/start
if necessary.
