and use this when masking/unmasking interrupts.
Maintain a mapping from (iopaic number, int pin) tuple to irq number,
and use this when configuring devices and programming the ioapics.
Previous code assumed that irq number was equal to int pin number, and
that the ioapic number was 0.
Don't let an AP enter _cpu_switch before all local apics are initialized.
Add a sysctl 'machdep.cs_recv_delay' to specify how long to wait after
receiving a packet in order to check for a subsequent (back-to-back)
packet. The cs8900 has a very small receive buffer, so this helps avoid
overflows at the cost of some extra CPU overhead.
Submitted by: Oleg Sharoiko <os@rsu.ru>, MIHIRA "Sanpei" Yoshiro <sanpei@sanpei.org>
for the Lite2 fix for always returning EIO in dead_read().
Cleaned up the cdevswitch initializers for all tty drivers.
Removed explicit calls to ttsetwater() from all (tty) drivers. ttsetwater()
is now called centrally for opens, not just for parameter changes.
The check for dropping unicast packets not sent to our ethernet
address is after the bpf tap, but not conditioned on it. All packets
received should get handed to bpf, and unicast packets not to us (mac)
should get dropped whether or not there is a bpf listener. I believe
that the common optimization that the interface is in hw promisc mode
iff there is a bpf listener is in general wrong, but more frequently
so on wavelans.
I think Max's fix makes bpf listeners not see unicast packets sent to
others, but I'm not sure.
One can argue that checking on MOD_ENAL is wrong, but the code only
drops packets that shouldn't be received. The correctness condition
is that it be run whenever unicast packets without our mac address can
be received.
PR: kern/7144
Submitted by: Greg Troxel <gdt@ir.bbn.com>
for 1 second's worth of input) and larger tty output buffers. The
interrupt-level buffers are still too small for speeds above 115200
bps (only a little too small for 230400 bps if RTS flow control is
enabled).
Don't call ttsetwater() explicitly in open(). It is now called for
the TTYDISC l_open() and should be static.
Don't attempt to register the cdevsw more than once.
I don't have access to a real VT220 to verify this against.
However, I'm committing the patch in `good faith' because
(a) getting hold of a real VT220 is going to be increasingly difficult
the longer the PR sits around,
(b) some one was troubled enough to in a PR and
(c) the fix is minor and has no other implications.
PR: 7559
Submitted by: Christian Weisgerber <naddy@mips.rhein-neckar.de>
of invariants to cyattach().
Fixed minor bugs:
- cyparam() returned without restoring the ipl in the error cases. This
was harmless because cyparam() is always called at spltty().
- one check for "rev. J or higher" actually checked for precisely rev. J.
swapped RTS/DTR). Merge the vendor's modification of the 2.2.6-release
version into -current for reference. Will be cleaned up in next commit.
Obtained from: ftp://ftp.cyclades.com/pub/cyclades/cyclom-y/freebsd/2.2.6/cyy226.tar.gz
instead of at compile time using ifdefs.
Use _swi_null instead of dummycamisr. CAM and dpt should call
register_swi() instead of hacking on ihandlers[] directly.
in ddb) which I broke by changing %8[l]x to %8p. Hacked the central
printf routine to not add an "0x" prefix for %p formats if the field
width is nonzero. The tables are still horribly misformatted on
64-bit machines.
Use %p instead of %8p to print pointers when the field width isn't
important.
chip.
It has been observed that the problem is most apparent:
a) in notebook computers,
b) and/or in the systems with C&T video chips.
Define the new configuration option SC_BAD_FLICKER in the kernel
configuration file to remove outb()/outw() calls in question.
DOS partition type 15 (Extended DOS, LBA) as a container for
DOS logical volumes, so the appropriate slices (e.g. sd1s5)
are not initialized.
PR: 7549
PR: 4120
Reviewed by: phk
Submitted by: Jim Mattson <jmattson@sonic.net>
- ppbus now supports PLIP via the if_plip driver
- ieee1284 infrastructure added, including parallel-port PnP
- port microsequencer added, for scripting the sort of port I/O
that is common with parallel devices without endless calls up and down
through the driver structure.
- improved bus ownership behaviour among the ppbus-using drivers.
- improved I/O chipset feature detection
The vpo driver is now implemented using the microsequencer, leading to
some performance improvements as well as providing an extensive example
of its use.
Reviewed by: msmith
Submitted by: Nicolas Souchu <Nicolas.Souchu@prism.uvsq.fr>
saver and splash screen can all work properly with syscons. Note that
the splash screen option (SC_SPLASH_SCREEN) does not work yet, as it
requires additional code from msmith.
- Reorganized the splash screen code to match the latest development
in this area.
- Delay screen switch in `switch_scr()' until the screen saver is
stopped, if one is running,
- Start the screen saver immediately, if any, when the `saver' key is
pressed. (There will be another commit for `kbdcontrol' to support
this keyword in the keymap file.)
- Do not always stop the screen saver when mouse-related ioctls
are called. Stop it only if the mouse is moved or buttons are
clicked; don't stop it if any other mouse ioctls are called.
2. Added provision to write userland screen savers. (Contact me if you
are interested in writing one.)
- Added CONS_IDLE, CONS_SAVERMODE, and CONS_SAVERSTART ioctls to
support userland screen savers.
3. Some code clean-ups.
the screen mode is changed even if another vty has larger size.
Reallocate the buffer only when the new screen size is larger than
the current cut buffer size.
When bell is of "quiet" types, the console won't ring (or flush)
if the ringing process is in a background vty.
PR: i386/2853
- Modify the escape sequence 'ESC[=%d;%dB' so that bell pitch and
duration are set in hertz and msecs by kbdcontrol(1).
There will be a corresponding kbdcontrol patch.
PR: bin/6037
Submitted by: Kouichi Hirabayashi (kh@eve.mogami-wire.co.jp)
and DSO_NOLABELS flags prevent searching for slices and labels
respectively. Current drivers don't set these flags. When
DSO_NOLABELS is set, the in-core label for the whole disk is cloned
to create an in-core label for each slice. This gives the correct
result (a good in-core label for the compatibility slice) if
DSO_ONESLICE is set or only one slice is found, but usually gives
broken labels otherwise, so DSO_ONESLICE should be set if DSO_NOLABELS
is set.
- Call isa_dmadone() whenever necessary to stop DMA and/or free bounce
buffers. Undead DMA corrupted the malloc freelist fairly consistently
in the following configuration: SLICE kernel, 2 floppy drives, no disk
in fd0, disk in fd1.
- Don't call fdc_reset() from fd_timeout(). Doing so gave an "extra"
interrupt which was usually misinterpreted as being for completion
of the next FDC command; the interrupt for completion of the next
FDC command was then usually misinterpreted... There were further
complications for interrupts latched by the soft-spl mechanism so
that they were delivered after all the h/w interrupts went away.
This caused at least wrong head settle delays and may be why the
FreeBSD floppy driver seems to munch floppies more than most floppy
drivers. The reset was unnecessary anyway in cases that didn't have
the bug described next, since is was repeated a little later for
the IOTIMEDOUT state. The state machine has complications to handle
resets correctly, so just use it.
- Don't call retrier() from fd_timeout(). The IOTIMEDOUT state needs
to be processed next, and it isn't valid to set to that state if
retrier() has aborted the current transfer. Doing so caused null
pointer panics after the previous bug was fixed.
Improved error handling:
- If an i/o is aborted, arrange to reset in the state machine before
doing the next i/o. New fdc flag for this. This fixes spurious
warnings and lengthy busy-waiting for the next i/o.
- Split STARTRECAL into RESETCOMPLETE and STARTRECAL and only check
for the results from reset if we actually reset. This fixes spurious
warnings for other paths to STARTRECAL. [Oops, it may break reset
handling for motor-off resets.]
Cleanups in fd_timeout():
- Renamed to fd_iotimeout() to make it clearer that it is only used
for i/o.
- Don't handle the bp == 0 case. This case can't happen for i/o.
- Don't check for controller-busy. We know it must be.
- Don't print anything. retrier() already prints too much for normal
errors.
- Fudge the state differently so that the state machine advances
fdc->retry and the status is invalid (perhaps this should fudge a
valid state like the one for WP).
- Style fixes.
small part of a bug suite beginning in the SLICE probes but mostly in the
floppy driver. This is a quick fix: the auto case shouldn't be special;
DMA should also be stopped in isa_dma_release(); isa_dmastop() probably
shouldn't exist; common DMA registers should not be accessed without
locking.
controller reports a successful seek, it is very unlikely to report
seeking to a cylinder other than the one requested, but we check for
this, and botched the error handling for the requested_cylinder != 0
case. This error happened when the bug fixed in rev.1.52 of <sys/buf.h>
caused the head of buffer queue to change to one starting on a different
cylnder - the requested cylinder was found, but it wasn't what we
thought we requested. The fix is simply to arrange to reset the state
machine.
Corruption of the buffer queue seems to only have been a problem in the
floppy driver. Other drivers dequeue the head of the queue before doing
physical i/o on it, so the corruption at worse broke the elevator sort
order. Dequeueing breaks it anyway.
These asm statments are not quite as pessimal as when I complained
about them in rev.1.9 of audio.c. They seem to be only 40% slower
than the C version on P5's and the same speed on K6's.
interupt level events. This needs a lot of cleanup, but has been working
here for a month or two.. originally needed for CAM integration
but that hasn't happenned yet. The probing state machines for each
handler should be replaced by a more generic state-service. It's
still quite messy in there..
is the kernel part of my commits, the userlevel stuff will be done in
a separate commit. Add the ability to suspend as well as hibernate to
syscons. Create a new virtual key like hibernate for suspend. Update
apm_bios.h to define more apm bios goodies.
There is only cdevsw (which should be renamed in a later edit to deventry
or something). cdevsw contains the union of what were in both bdevsw an
cdevsw entries. The bdevsw[] table stiff exists and is a second pointer
to the cdevsw entry of the device. it's major is in d_bmaj rather than
d_maj. some cleanup still to happen (e.g. dsopen now gets two pointers
to the same cdevsw struct instead of one to a bdevsw and one to a cdevsw).
rawread()/rawwrite() went away as part of this though it's not strictly
the same patch, just that it involves all the same lines in the drivers.
cdroms no longer have write() entries (they did have rawwrite (?)).
tapes no longer have support for bdev operations.
Reviewed by: Eivind Eklund and Mike Smith
Changes suggested by eivind.
mmioctl() to fix hundreds of style bugs and a few error handling bugs
(don't check for superuser privilege for inappropriate ioctls, don't
check the input arg for the output-only MEM_RETURNIRQ ioctl, and don't
return EPERM for null changes).
`void *' arg. Fixed or hid most of the resulting type mismatches.
Handlers can now be updated locally (except for reworking their
global declarations in isa_device.h).
and don't depend on them being declared there. This will cause lots of
warnings for a few minutes until config is updated. Interrupt handlers
should never have been configured by config, and the machine generated
declarations get in the way of changing the arg type from int to void *.
over from the probe are now expected for incompatible UARTs that
deliver IRQs as a strobe (low) instead of a level (high).
Discard events on going-away devices too. Endless loops may have
been possible when an active pccard was removed.
or unsigned int (this doesn't change the struct layout, size or
alignment in any of the files changed in this commit, at least for
gcc on i386's. Using bitfields of type u_char may affect size and
alignment but not packing)).
FreeBSD/alpha. The most significant item is to change the command
argument to ioctl functions from int to u_long. This change brings us
inline with various other BSD versions. Driver writers may like to
use (__FreeBSD_version == 300003) to detect this change.
The prototype FreeBSD/alpha machdep will follow in a couple of days
time.
miscconfigured case) if the port is the console. This fixes several
bugs:
- if all sioprobe()s failed, then the console driver followed null
pointers in cdevsw[].
- if the sioprobe() for the console failed but another sioprobe()
succeeded, then init hung early when the console couldn't be
opened.
- it was silly for the console to not be there after printing boot
messages on it.
Bugs introduced by this are hopefully no worse than old ones caused
by forcing the success of the `cn' level probe.
Only complain about an irq mismatch in the probe if the configured
irq doesn't become active, and then print the bitmap of irqs that
became active (including clock irqs) instead of just the first
(not including clock irqs).
Bugs reported by: msmith
a test of the irq number, and made failure of this test non-fatal.
Removed related unused complications for the APIC_IO case. Removed the
no-test3 flag.
Deverbosified the failure messages for the other tests. Removed the
per-port verbose flag - just use the general verbose flag.
Clean up (or if antipodic: down) some of the msgbuf stuff.
Use an inline function rather than a macro for timecounter delta.
Maintain process "on-cpu" time as 64 bits of microseconds to avoid
needless second rollover overhead.
Avoid calling microuptime the second time in mi_switch() if we do
not pass through _idle in cpu_switch()
This should reduce our context-switch overhead a bit, in particular
on pre-P5 and SMP systems.
WARNING: Programs which muck about with struct proc in userland
will have to be fixed.
Reviewed, but found imperfect by: bde
i contains the contents of the EP_W0_CONFIG_CTRL register.
i was being used as the array index into an array on the stack.
j is initialized to 0 as it should be.
PR: kern/6757
Reviewed by: jmb
Submitted by: Stephane E. Potvin <sepotvin@videotron.ca>
update of cpu usage as shown by top when one process is cpu bound
(no system calls) while the system is otherwise idle (except for top).
Don't attempt to switch to the BSP in boot(). If the system was idle when
an interrupt caused a panic, this won't work. Instead, switch to the BSP
in cpu_reset.
Remove some spurious forward_statclock/forward_hardclock warnings.
but doesn't do much of anything with it. I added it to siopnp_ids[]
and it was found and recognized as a serial port.
PR: 6605
Reviewed by: phk
Submitted by: Dave Marquardt <marquard@zilker.net>
Support >8G drives in CHS mode. This is done by guesstimating the
cylinder count from the LBA size reported. It works on my shiny
new Maxtor 11.5G drive, YMMV.
Reports from users of other big drives (read Quantum bigfoot's)
are welcome...
This code will be turned on with the TWO options
DEVFS and SLICE. (see LINT)
Two labels PRE_DEVFS_SLICE and POST_DEVFS_SLICE will deliniate these changes.
/dev will be automatically mounted by init (thanks phk)
on bootup. See /sys/dev/slice/slice.4 for more info.
All code should act the same without these options enabled.
Mike Smith, Poul Henning Kamp, Soeren, and a few dozen others
This code does not support the following:
bad144 handling.
Persistance. (My head is still hurting from the last time we discussed this)
ATAPI flopies are not handled by the SLICE code yet.
When this code is running, all major numbers are arbitrary and COULD
be dynamically assigned. (this is not done, for POLA only)
Minor numbers for disk slices ARE arbitray and dynamically assigned.
is that the previous commit spammed a hacked 2.2-stable onto -current,
deleting the DMA support etc. (I guess that's one way of minimizing diffs
between -current and -stable.. :-] )
device. But with devfs, currently, /dev/psm0 is the blocking device
and /dev/npsm0 is the non-blocking one.
DEVFS must stay consistent with the older behaviour.
PR: 6260
Reviewed by: phk
Submitted by: Kapil Chowksey <kchowksey@hss.hns.com>
is a tremendous perf decrease due to the disabling of advanced
features such as DMA, Ultra DMA, and 32bit mode. This patch
might have been reported by someone else (I seem to remember
it.)
Use config flags 0x1000 to enable LBA mode. It should be enabled in
the BIOS too to avoid geometry confusion.
One catch though, I'm not sure all BIOS's uses the 64head/63secs
translation, all mine does but....
- Set the correct value scp->font_size in init_scp().
- Set scp->font_size to FONT_NONE for VGA_MODEX.
Interim fix for a font problem:
- A kludge to display the correct font on some video cards.
We should be able to load multiple fonts to the VGA plane #2 and switch
between fonts by setting the font select register in the VGA sequencer.
It appears that the current code isn't functioning as expected on
some VGA cards (I have reports on Millenium and Mach64 cards). This is
either a bug in syscons or a hardware compatibility problem ;-<
This kludge will always load only one font set at a time and always use
the font page #0 on the plane #2. It is an interim kludge until
we find the exact cause and solution.
Small adjustment for mouse cursor handling:
- Turn off the mouse cursor early when changing video modes.
Video mode switch fixes:
- Stop the screen saver when changing video modes.
- Enclose the critical section with a pair of spltty()/splx().
- A kludge to prevent scrn_update() from accessing video memory in less-
critical sections in video mode change; artificially turn on the
UNKNOWN_MODE flag.
PR: bin/5899, bin/5907
Tested by: ache and a couple of users
OKed by: sos
* Figure out UTC relative to boottime. Four new functions provide
time relative to boottime.
* move "runtime" into struct proc. This helps fix the calcru()
problem in SMP.
* kill mono_time.
* add timespec{add|sub|cmp} macros to time.h. (XXX: These may change!)
* nanosleep, select & poll takes long sleeps one day at a time
Reviewed by: bde
Tested by: ache and others
"time" wasn't a atomic variable, so splfoo() protection were needed
around any access to it, unless you just wanted the seconds part.
Most uses of time.tv_sec now uses the new variable time_second instead.
gettime() changed to getmicrotime(0.
Remove a couple of unneeded splfoo() protections, the new getmicrotime()
is atomic, (until Bruce sets a breakpoint in it).
A couple of places needed random data, so use read_random() instead
of mucking about with time which isn't random.
Add a new nfs_curusec() function.
Mark a couple of bogosities involving the now disappeard time variable.
Update ffs_update() to avoid the weird "== &time" checks, by fixing the
one remaining call that passwd &time as args.
Change profiling in ncr.c to use ticks instead of time. Resolution is
the same.
Add new function "tvtohz()" to avoid the bogus "splfoo(), add time, call
hzto() which subtracts time" sequences.
Reviewed by: bde
everything is contained inside #ifdef VM86, so this option must be
present in the config file to use this functionality.
Thanks to Tor Egge, these changes should work on SMP machines. However,
it may not be throughly SMP-safe.
Currently, the only BIOS calls made are memory-sizing routines at bootup,
these replace reading the RTC values.
- Implement proper EISA probing.
- Better support for the new transputer based host cards.
- use standard termios settings, one can use the intial/lock devices.
- use a simple bcopy since some cards/systems apparently don't support
32 bit accesses.
- hard reset and halt host card CPU prior to download in case of a soft
restart.
- recognize new remote module types (ASIC vs. CD1400 based)
- a number of cosmetic changes (my fault, not Nick's)
Submitted by: Nick Sayer <nsayer@quack.kfu.com>
Don't try to flush buffers if the drive says it has none.
More error checking and reporting.
Hack: if drive hangs, it can be reset by issuing a mt -f device offline.
I've been able to make several 4G backups. However there is still problems
with some configurations. It is not clear if it is hardware or driver
problems yet.
on the IOAPIC being connected to the 8254 timer interrupt.
Verify that timer interrupts are delivered. If they aren't, attempt
a fallback to mixed mode (i.e. routing the timer interrupt via the 8259 PIC).
interrupts are masked, and EOI is sent iff the corresponding ISR bit
is set in the local apic. If the CPU cannot obtain the interrupt
service lock (currently the global kernel lock) the interrupt is
forwarded to the CPU holding that lock.
Clock interrupts now have higher priority than other slow interrupts.
the signal handling latency for cpu-bound processes that performs very
few system calls.
The IPI for forcing an additional software trap is no longer dependent upon
BETTER_CLOCK being defined.
It does endeed work, but there is still some problems to solve.
I get a "nonrecovered data error" from time to time, but besides
this it has backed up several Gigs allready.
Please report any success/failure directly to me.
Thanks to Warner Losh for providing a drive to use in writing
this driver!
it runs at a constant frequency. This was less of an issue before,
because the TSC only interpolated in the HZ intervals, but now where
the timecounter is used all the way, this becomes much more visible.
Nit: Fix a printf which triggered the bde-filter.
signals delivered to a process writing to the audio device the
system: if you try
cat /dev/zero > /dev/dsp (or cat /dev/zero > /dev/pcaudio)
and press Ctrl-C : for a second or two the system appears to freeze
(e.g. the cursor will disappear if you move the mouse, xclock
blocks, etc.). I think that interrupts etc. still run so the problem
is not too terrible, but still annoying
[ The problems appears to also be in isa/pcaudio.c, though that is ignored ]
Submitted by: Luigi Rizzo <luigi@labinfo.iet.unipi.it>
Highlights:
* Simple model for underlying hardware.
* Hardware basis for timekeeping can be changed on the fly.
* Only one hardware clock responsible for TOD keeping.
* Provides a real nanotime() function.
* Time granularity: .232E-18 seconds.
* Frequency granularity: .238E-12 s/s
* Frequency adjustment is continuous in time.
* Less overhead for frequency adjustment.
* Improves xntpd performance.
Reviewed by: bde, bde, bde
select/poll and DEVFS changes, which are limited to an include/define
in sound.h and the actual select/poll implementation in sound.c
[ This commit is blind, but the code is similar enough that there will
hopefully be no problems. ]
The differences Terrys patch and this patch are:
* Remove a lot of un-needed comments.
* Don't put l_hotchar at the front of stuct linesw, there is no need to.
* Use the #defines for the hotchar in the SLIP and PPP line disciplines
with macros. This breaks if the functions are replaced by macros with
unsuitable semantics. Define a MAX() macro unconditionally instead.
max() is unsuitable since we need a constant expression. Don't define
MIN() - we never used min().
is "acquired". This fixes a TSC biasing error of about 10 msec when
pcaudio is active.
Update `time' before calling hardclock() when timer0 is being released.
This is not known to be important.
Added some delays in writertc(). Efficiency is not critical here, unlike
in rtcin(), and we already use conservative delays there.
Don't touch the hardware when machdep.i8254_freq is being changed but
the maximum count wouldn't change. This fixes jitter of up to 10 msec
for most small adjustments to machdep.i8254_freq. When the maximum
count needs to change, the hardware should be adjusted more carefully.
this using option "-b" to the boot blocks. It is smartest to compile
a font into your kernel (See LINT), but not mandatory, but apart from
the cursor you will see nothing on the screen until you load a font.
This mode allows XF86_VGA16 to run in 800x600 mode on otherwise unsupported
graphics hardware.
A number of buglets in the cursor handling in syscons may become
visible this way.
actually faster (more than 20% faster for zeroing 1 MB at boot time).
This fixes pessimized copying and zeroing on K6's and perhaps on other
CPUs that are misclassified as i586's.
mode switch in ioctl.
Possibly related to PR: kern/4271
- A kludge: initialize scp->xpixel and ypixel even in the text mode.
If the console enters the `unknown' graphics mode via the ioctl KDSETMODE
(KD_GRAPHICS), these fields are not set (because syscons cannot know
the correct values), but set_mouse_pos() need to refer to these field
to adjust the mouse position.
- Turn off MOUSE_VISIBLE when switching video mode by ioctl.
- another new option: SC_MOUSE_CHAR
Define the first character code of four consecutive codes to be used for
the mouse cursor. Default codes are 0xd0 through 0xd3. Beware that
if you decide to use any codes outside the range of 0xc0-0xdf,
the mouse cursor may not look good, because of the way VGA displays
characters in 9-dot-wide character cells.
Requested by several people.
(This patch was tested by a person who recently reported, in the -current
ML, a page fault problem in the kernel (draw_mouse_iamge()) after
X server shutdown. The patch cured his problem.)
Don't touch/update the screen while manipulating font data.
Possibly related to PR: kern/4271
- Set up VGA in alphanumeric mode rather than graphics mode when
loading font into video memory. This will drastically reduce flicker.
PR: bin/2977
- Set up scp->font_size properly during video mode switch caused by
ioctl.
separate routine: scupdate() called from scrn_timer().
- Make sure that the screen is updated for the low-level console
routines sccngetc() and sccncheckc(). A new routine, sccnupdate(),
is introduced and will call scupdate() above.
Requested by: bde and msmith
OKed by: sos
from the low-level console routines sccngetc() and sccncheckc().
Submitted by: bde (a long time ago)
- Don't try to ring bell and immediately return from do_bell() while
device probe is in progress at boot time; the timeout queue is not
functional yet.
PR: kern/2424
- Stop running the screen saver after panic() is called: check
if `panicstr' is non-NULL during scrn_timer().
PR: kern/5314
- A new option: SC_DISABLE_REBOOT
The reboot key (usually Ctl-Alt-Del) will be ignored if this option
is defined. You may still have the reboot key defined in the keymap and
it won't cause error when the keymap is loaded, but it will be quietly
treated as nop.
OKed by: sos
prematurely when there was a hole (for a cdrom or an unused
interface) in the sequence of wd drives. This caused non-free
wd units to be probed as atapi drives. There was no problem
provided the atapi probe failed correctly.
All known versions of this drive (firmware 21.* and 23.*) will lock up
if presented with a read/write request of > 64 blocks. In the presence
of such a unit, I/O requests of > 64 blocks are fragmented to avoid
this.
This introduce an xxxFS_BOOT for each of the rootable filesystems.
(Presently not required, but encouraged to allow a smooth move of option *FS
to opt_dontuse.h later.)
LFS is temporarily disabled, and will be re-enabled tomorrow.
so that existing programs which were compiled before the introduction
of the new mouse code and use these ioctls will run unmodified.
Suggested by msmith.
This is Junichi's v1.0 driver.
NOTE: Major device numbers have been changed to avoid conflict with other
FreeBSD 3.0 devices. The new numbers should be considered "official."
This driver is still considered "beta" quality, although we have been
playing with it. Please submit bugs to junichi and myself.
Submitted by: junichi@astec.co.jp
(accent_key + space does still print the accent letter too, as in
the previous commit.)
Requested by a couple of users.
- Clear the accent flag when the next_screen key is pressed.
- Added some comment lines regarding accent key processing.
This will not make any of object files that LINT create change; there
might be differences with INET disabled, but hardly anything compiled
before without INET anyway. Now the 'obvious' things will give a
proper error if compiled without inet - ipx_ip, ipfw, tcp_debug. The
only thing that _should_ work (but can't be made to compile reasonably
easily) is sppp :-(
This commit move struct arpcom from <netinet/if_ether.h> to
<net/if_arp.h>.
- IIR_TXRDY is never off even if reading a IIR register.
- Know as PIAFS "Palido 321S", "DC-*S" oemed by Sharp corp.
2. Omiting a restrict probing if it's already probed by pccardd.
Note: Define a new id_flags as follows
0x40000 - NO PROBE (Already probed as serial)
0x80000 - Has a bogus IIR_TXRDY register
Sato Junichi <junichi@astec.co.jp>
Nrihiro Kumagai <kuma@slab.tnr.sharp.co.jp>
Hirao Tetsuya <ai.cs.fujitsu.co.jp>
Toshiharu Asai <asai@mbc.infoshere.or.jp>
Shin'ya Kumabuchi <kumabu@t3.rim.or.jp>
Freebsd-users-jp@jp.freebsd.orgbsd-nomads@ai.cs.fujitsu.co.jp
With a keymap with accent key definitions loaded to syscons, you press
an accent key followed by a regular letter key to produce an accented
letter. Press an accent key followed by the space bar to get the
accent letter itself.
Code is based on the ideas and work by jmrueda@diatel.upm.es and
totii@est.is.
PR: i386/4016
console.h
- Defined structures and constants for accent (dead) keys.
syscons.c, kbdtables.h
- When an accent key is pressed, set the corresponding index to
`accents'. If the next key is the space key, produce the accent char
itself. Otherwise search the accent key map entry, indexed by
`accents', for a matching pair of a regular char and an accented char.
- Added ioctl functions to set and get the accent key map (PIO_DEADKEYMAP
and GIO_DEADKEYMAP).
necessary to call it when the tty layer's output state has not been
changed, but siostop() sometimes changes the TS_BUSY state and then
calls comstart() mainly for its side effect of calling ttwwakeup().
need to do it directly, since ttwwakeup() is always called just before
returning from rpstart(). The brokenness was waking up the wrong address
after clearing TS_SO_OLOWAT. It's not clear how processes waiting for
output to drain below low water ever got woken up.
Found by: when I fixed longstanding warts in output watermark
handling, this was the only driver that knew too much
(anything) about the watermarks
It failed to recognize the PCI bus in a system that had only an
old chip-set (class code 000000) and a Cyclom multiport serial
card on PCI bus 0, but no VGA card or disk or network controller.
PR: i386/5300
Submitted by: Nickolay N. Dudorov <nnd@itfs.nsk.su>
The #ifdef IPXIP in netipx/ipx_if.h is OK (used from ipx_usrreq.c and
ifconfig.c only).
I also fixed a typo IPXTUNNEL -> IPTUNNEL (and #ifdef'ed out the code
inside, as it never could have compiled - doh.)
- A nonprofiling version of s_lock (called s_lock_np) is used
by mcount.
- When profiling is active, more registers are clobbered in
seemingly simple assembly routines. This means that some
callers needed to save/restore extra registers.
- The stack pointer must have space for a 'fake' return address
in idle, to avoid stack underflow.
(mutant) Crystal CSS4236 chip on the Intel PR440FX SMP motherboard.
XXX this uses some rather ugly PnP bootstrap code that is *NOT* compatable
with 'controller pnp0' or *ANY* other PnP devices. If you use some other
PnP devices, enabling css0 will burn your house down. :-] The
"simplified" PnP init sequence directly blats your config(8) settings onto
the chip. I'm pretty sure 'css0' will conflict with 'mss0', this whole
area desperately needs a cleanup.
I have been using the following with some success on the PR440FX:
controller snd0
device css0 at isa? port 0x534 irq 5 drq 1 flags 0x08 vector adintr
device opl0 at isa? port 0x388
device mpu0 at isa? port 0x330 irq 10 vector mpuintr
Wrappered and enabled by the define BETTER_CLOCK (on by default in smpyests.h)
apic_vector.s also contains a small change I (smp) made to eliminate
the double level INT problem. It seems stable, but I haven't the tools
in place to prove it fixes the problem.
Reviewed by: smp@csn.net
Submitted by: Tor Egge <Tor.Egge@idi.ntnu.no>
MS IntelliMouse, Kensington Thinking Mouse, Genius NetScroll,
Genius NetMouse, Genius NetMouse Pro, ALPS GlidePoint, ASCII
MieMouse, Logitech MouseMan+, FirstMouse+
- The `psm' driver is made to recognize various models of PS/2 mice
and enable their extra features so that their additional buttons and
wheel/roller are recognized. The name of the detected model will be
printed at boot time.
- A set of new ioctl functions are added to the `psm', `mse' and
`sysmouse' drivers so that the userland program (such as the X server)
can query device information and change driver settings.
- The wheel/roller movement is handled as the `Z' axis movement by the
mouse drivers and the moused daemon. The Z axis movement may be mapped
to another axis movement or buttons.
- The mouse drivers support a new, standard mouse data format,
MOUSE_PROTO_SYSMOUSE format which can encode x, y, and x axis movement
and up to 10 buttons.
/sys/i386/include/mouse.h
- Added some fields to `mousestatus_t' to store Z axis movement
and flag bits.
- Added the field `model' to `mousehw_t' to store mouse model code.
Defined model codes.
- Extended `mousemode_t'.
- Added new protocols and some constants for them.
- Added new ioctl functions and structures.
- Removed obsolete ioctl definitions.
/sys/i386/include/console.h
- Added `dz' field to the structure `mouse_data' to pass Z axis movement
to `syscons/sysmouse'.
- Removed LEFT_BUTTON, MIDDLE_BUTTON and RIGHT_BUTTON. Use button bits
defined in `mouse.h' instead.
/sys/i386/isa/psm.c
- Added a set of functions to detect various mice which have additional
features (wheel and buttons) unavailable in the standard PS/2 mouse.
- Refined existing ioctl functions and added new ones. Most important
of all is MOUSE_SETLEVEL which manipulates the output level of the driver.
While the output level remains zero, the output from the `psm' driver is
in the standard PS/2 mouse format (three bytes long). When the level
is set to one, the `psm' driver will send data in the extended format.
At the level two the driver uses the format which is native to the
connected mouse is used. (Meaning that the output from the device is
passed to the caller as is, unmodified.) The `psm' driver will pass
such extended data format as is to the caller if the output level is
two, but emulates the standard format if the output level is zero.
- Added kernel configuration flags to set initial resolution
(PSM_CONFIG_RESOLUTION) and acceleration (PSM_CONFIG_ACCEL).
- Removed the compile options PSM_ACCEL, PSM_CHECKSYNC and PSM_EMULATION.
Acceleration ratio is now specified by the kernel configuration flags
stated above. Sync check logic is refined and now standard.
The sync check can be turned off by the new kernel configuration flags
PSM_CONFIG_NOCHECKSYNC (0x100). PSM_EMULATION has been of little use.
- Summer clean up :-) Removed unused code and obsolete comments.
/sys/i386/isa/mse.c
- Created mseioctl() to deal with ioctl functions MOUSE_XXXX.
Most importantly, the MOUSE_SETLEVEL ioctl will change the
output format from the 5 byte format to the new, extended format
so that the caller can take advantage of Z axis movement and additional
buttons.
- Use constants defined in `mouse.h' rather than magic numbers.
/sys/i386/isa/syscons.c
- Changed scioctl() to reflect the new `console.h' and some of the new
ioctls defined in `mouse.h'. Most importantly, the MOUSE_SETLEVEL
ioctl will change the `sysmouse' output format from the MouseSystems
5 byte format to the new, extended format so that the caller can
take advantage of Z axis movement and additional buttons.
- Added support for double/triple click actions of the left button and
single click action of the right button in the virtual console. The
left button double click will select a word under the mouse pointer.
The triple click will select a line and the single click of the right
button will extend the selected region to the current position of
the mouse pointer. This will make the cut/paste support more compatible
with xterm.
/sys/i386/isa/kbdio.h
- Added PSM_INTELLI_ID.
make isa_dmacascade, isa_dmastart, isa_dmadone, and find_isadev MUCH
easier to be found by starting them at the beginging of the line...
remove braces inside of ifdef RESOURCE_CHECK... found by % in vi...
Here are the remanding changes required to support the Ensoniq
Soundscape using FreeBSD 3.0-current.
Notes:
1) ad1848_init already has code to detect if DMA_DUPLEX should
be set so it is not necessary (and is in fact a mistake) to
hard code setting it. Not all soundcards (i.e. the current
sscape driver) are capable of using DMA_DUPLEX.
2) The other changes are hopefully self explanatory. Feel free
to let me know if you need additional information.
Submitted by: john@feith.com (John Wehle)
"high resolution" profiling. The available clocks are:
- the i8254 clock
- on non-SMP i586's and i686's: the TSC
- on systems with I586_PMC_GUPROF configured, and PERFMON configured
and available: all the performance counters.
This is unfinshed (there are problems with locking out the PERFMON
device driver, and with losing calibration after switching the clock),
but better than static configuration or writing to kmem.
Changed ifdefs to avoid generating code for non-working option
combinations.
there is a natural place to initialize `safepri' in a future commit.
Spinoffs:
- spl0() gets called in the unlikely event that isa is not configured.
- configure() has better control over enabling interrupts.
- it is now less unclear that interrupts aren't actually enabled early.
Rev.1.48 of autoconf.c seems to have done the opposite of what was
intended - moving the isa_configure() call delayed the spl0() side
effect.
Added some comments about the bogons. Removed the splhigh() call since
it is a no-op.
checking the BIOS video mode paramter table. Now syscons uses the
parameter table even if some bits in the table are different from the
current VGA register settings.
Even if comp_vgaregs() finds that the BIOS video parameter table looks
totally unfamiliar to it, syscons allows the user to change the
current video mode to some modes which are based on the VGA 80x25
mode. They are VGA 80x30, VGA 80x50, VGA 80x60. In this case the user
will be warned, during boot, that video mode switching is only
paritally supported on his machine.
PR: bin/4477
this mouse can correctly operate only in the high resolution mode.
If the mouse pointer jumps to the top or left edge or the top-left
corner of the screen, try defining PSM_MSCKLUDGE in the kernel
configuration file. This option will put the mouse in the high
resolution mode during device initialization.
and don't include <sys/fcntl.h>. (The select -> poll changes replaced
fcntl macros by poll macros.)
Use <machine/*.h> instead of <i386/include/*.h>.
Fail the probe instead of crashing in the unlikely event that malloc()
fails.
Fixed #include order. <i386/isa/isa_device.h> will soon be a prerequisite
for <i386/isa/pnp.h>. Including both in alphebetical order gets this
right naturally.
years and gives a "laugh"able number of compile-time errors (see the
comment). main() just printed the struct sizes. This can be done
better by compiling with -g and reading off the sizes from the stabs.
Sorted #includes.
Fixed an unsigned vs signed comparison.
actually offsets, they are offsets scaled by dividing by 2^cy_align.
I use different values for cy_align since the -current values are
unnaturally scaled, so I need different offsets, and the wrong
offsets got committed.
Reported by: nnd@itfs.nsk.su (N.Dudorov)
This corresponds to Voxware 3.5-alpha-<something> and Amancio's guspnp21.
There was a bit of a FUBAR during the commmit, so not all files are
mentioned in this commit's mail.
X-rant: I have just started to _*HATE*_ CVS...
changes:
o rip the old select from his distribution to prevent extra pollution
o the code now uses audio dma, helps reduce clicks
o improved card support, should work in full duplex on sb16 cards
o add better voxware ioctl support pointed out by Joao Carlos Mendes
Luis <jonny@coppe.ufrj.br>
o remove an unused file that I included for more complete history
o and MANY other changes
I have personally tested this code with a CS4237 based card and an AWE32
(non-PnP). Both cards worked fine in 8bit and 16bit mode.
Very rudimentary, lots of error checks missing, but it works.
Dont do an ls on two different CD's though, it will eat your
changer mechanism for lunch :), this clearly needs some more
thought. Until then this will enable those with changers to
mount their multible CD's and doing "sensible" work....
Thanks to Andrew Gordon <arg@arg1.demon.co.uk> for donating a drive
(a NEC CDR-C251 4x4) that makes this possible to develop.
to define it by including <sys/kernel.h>. That broke PC-CARD
support for this driver, producing the dreaded "device allocation
failed" message. Surprisingly, the missing include caused only
two compiler warnings. The compilation still "succeeded" anyway.
in <machine/cpu.h>. Moved the declarations to <machine/cputypes.h>.
Fixed style bugs in the moved code. Fixed everything that depended on
the nested include. Don't include <machine/cpu.h> (in the changed files)
unless something in it is used directly.
usage at 0x100. Quoted Justin's quotation from the manual as well, to
explain the technical background.
PR: kern/4559
Submitted by: Stephen J. Roznowski <sjr@home.net>
use a Linker Set. Note, if a driver is loaded as an LKM if will have
to use the function call, but since none of the existing drivers
are loadable, this made things cleaner and boot messages nicer.
Obtained from: PAO-970616
flicker won't occur when set_border() is called.
- Properly restore the border color when switching virtual consoles.
Pointed out by: tony@dell.com
OKed by: sos
* Kill individual drivers 'suspend' routines, since there's no simple/safe
way to suspend/resume a card w/out going through the complete probe
at initialization time.
* Default to using the apm_pccard_resume sysctl code, which basically
pretends the card was removed, and then re-inserted. Suspend/resume
is now 'emulated' with a fake insert/removal. (Hence we no longer
need the driver-specific suspend routines.)
follow.
* Rename/reorder all of the pccard structures, change many of the member
names to be descriptive, and follow more closely other 'bus' drivers
naming schemes.
* Rename a bunch of parameter and local variable names to be more
consistant in the code.
* Renamed the PCCARD 'crd' device to be the 'card' device
* KNF and make the code consistant where it was obvious.
* ifdef'd out some unused code
check the value and caused kernel panic when a large value was given.
- Move the configuration option SC_HISTORY_SIZE from syscons.h to
syscons.c.
- Define the maximum total number of history lines of all consoles.
It is SC_HISTORY_SIZE*MAXCONS or 1000*MAXCONS; whichever is larger.
CONS_HISTORY will allow the user to set the history size up to
SC_HISTORY_SIZE unconditionally (or the current height of the console
if it is larger than SC_HISTORY_SIZE). If the user requests a larger
buffer, it will be granted only if the total number of all allocated
history lines and the requested number of lines won't exceed the maximum.
- Don't free the previous history buffer and leave the history buffer
pointer holding a invalid pointer. Set the pointer to NULL first, then
free the buffer.
PR: bin/4592
for a couple of external CD's (notably the Sony PRD-650).
Note: In order to get my CD recognized, I had to configure the CD under
Win95, but it seems to work now even if I turn it off.
Submitted by: PAO [minor mods by me]
floppy drive #0, regardless of what the CMOS says. This is intended
as a bandaid for those plagued with Compaq's idea to not announce the
floppy drive on their `Aero' notebook.
Using the device flags is not very nice (in particular since they
aren't per-drive but per-controller), but still looks a lot better to
me than the disgusting guesswork hack that was recently posted to
-hackers.
Doc update will follow shortly.
i was at it, do no longer insist on `PCVT_FREEBSD' being declared in
the config file, but default it to a reasonable value.
More cleanup to follow, but this part is safe for RELENG_2_2, too.
Distribute all but the most fundamental malloc types. This time I also
remembered the trick to making things static: Put "static" in front of
them.
A couple of finer points by: bde
shown to be harmful in that it results in the card not being detected
properly on warmboot due to the station address failing to be read
correctly from the NVRAM.
much like the scancode mode.
However the keys that (for no good reason) returns extension codes
etc, are translated into singlebyte codes.
Needed by libvgl. This makes life ALOT easier, also the XFree86
folks could use this.
It seems I didn't count my 0's properly when adding the new masks into
icu_vector.s pushing SWI_AST_MASK off the end of the array and screwing
up the indexing for SWI_CLOCK_MASK.
Fix the bug icu_vector.s and also reformat the code in both icu_vector.s and
apic_vector.s so that it will be much harder to make the same mistake in
the future.
Submitted by: Bruce Evans <bde@zeta.org.au>
machine generates an NMI for each floating point error, just like an old XT.
Since it is ISA only, reading the EISA status port yields 0xff, which would
give a spurious EISA panic. The simplest thing to do is to ignore the 0xff.
- some addition of comments (for readability)
- iso-2022 G0 designation support. This does almost nothing. Just for
avoiding garbled screen when got "ESC ( B".
(how about G1/2/3 designation? I'm not sure)
