VideoCore reports garbage in viewport geometry fields unless
viewport was set previously by earlier stage boot loader. So
when booting FreeBSD kernel directly from VideoCore's start.elf
framebuffer intialization fails due to invalid vxres, vyres
values. Make sure we request viewport to be equal to physical
resolution
Submitted by: Sylvain Garrigues <sylvain@sylvaingarrigues.com>
write to the End of Interrupt (EOI) register before handling the interrupt.
This should be a noop as it will be set for all edge triggered interrupts,
however this will not be the case for MSI interrupts. These are also edge
triggered, however we should not write to the EOI register until later in
arm_gic_pre_ithread.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
support MSI and MSI-X interrupts, however intrng needs updates before this
can happen.
For now we just attach the driver until the MSI API is ready.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D5950
- Pre-buffer audio data to VideoCore so there are no audible glitches when
driver is too late to provide samples
- Start actual playback when there is some prebuffered audio,
it fixes audible noisy click in the beginning of playback
- Use #defines instead of hardcoded values where appropriate
- Fix copy-pasted comment
PR: 208678
value that can't ever be in an inconsistant intermediate state even when
some other thread is in the middle of writing the value/register.
Locking of the hardware remains in the few places that do r-m-w operations.
Locking of metadata access is restricted to places using memcpy or sprintf
to modify the metadata.
oddly separated from related functionality. This just moves some blocks
of code around so that setup_intr and teardown_intr are near each other
again, and likewise for enable/disable_intr. No functional changes.
The PLL_X, base CPU frequency source, doesn't have a bypass switch and thus
we must use another frequency source for CPU while changing its frequency.
PLL_P is ideal for this, it runs at 480MHz and CPU can be clocked at this
frequency at any CPU voltage.
many SoCs these two are the same, however there is no requirement for this
to be the case, e.g. on the ARM Juno we boot on what the GIC thinks of as
CPU 2, but FreeBSD numbers it CPU 0.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
a child of it. This is done in conformity with Linux dts files and
as preparation for rework of BCM2836 interrupt controller for INTRNG.
Reviewed by: gonzo
Differential Revision: https://reviews.freebsd.org/D5807
universal.
(1) New struct intr_map_data is defined as a container for arbitrary
description of an interrupt used by a device. Typically, an interrupt
number and configuration relevant to an interrupt controller is encoded
in such description. However, any additional information may be encoded
too like a set of cpus on which an interrupt should be enabled or vendor
specific data needed for setup of an interrupt in controller. The struct
intr_map_data itself is meant to be opaque for INTRNG.
(2) An intr_map_irq() function is created which takes an interrupt
controller identification and struct intr_map_data as arguments and
returns global interrupt number which identifies an interrupt.
(3) A set of functions to be used by bus drivers is created as well as
a corresponding set of methods for interrupt controller drivers. These
sets take both struct resource and struct intr_map_data as one of the
arguments. There is a goal to keep struct intr_map_data in struct
resource, however, this way a final solution is not limited to that.
(4) Other small changes are done to reflect new situation.
This is only first step aiming to create stable interface for interrupt
controller drivers. Thus, some temporary solution is taken. Interrupt
descriptions for devices are stored in INTRNG and two specific mapping
function are created to be temporary used by bus drivers. That's why
the struct intr_map_data is not opaque for INTRNG now. This temporary
solution will be replaced by final one in next step.
Differential Revision: https://reviews.freebsd.org/D5730
separate driver. Add support for activating clock and hwreset resources
for these devices when the EXT_RESOURCES option is present.
Reviewed by: andrew, mmel, Emmanuel Vadot <manu@bidouilliste.com>
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D5749
This driver works in PIO mode for now, interrupts are available only when
FIFO is enabled. The FIFO cannot be used with arbitrary sizes which defeat
its general use.
At some point we can add DMA transfers where the FIFO can be more useful.
Tested on uBMC (microBMC) and BBB.
Sponsored by: Rubicon Communications (Netgate)
different ID space than the kernel. Because of this we need to read the
ID from the hardware. The hardware will provide this value to the CPU by
reading any of the first 8 Interrupt Processor Targets Registers.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D5706
- in atags
- in DT blob (by using 'fdt chosen' U-Boot command)
The command line must start with guard's string 'FreeBSD:' and can contain
list of comma separated kenv strings. Also, boot modifier strings from
boot.h are recognised and parsed into boothowto.
The command line must be passed from U-Boot by setting of bootargs variable:
'setenv bootargs FreeBSD:boot_single=1,vfs.root.mountfrom=ufs:/dev/ada0s1a'
followed by 'fdt chosen' (only for DT based boot)
- Don't convert atags address passed from U-Boot. It's real physical
address (and we have 1:1 mapping).
- Size of tags is encoded in words, not in bytes
This allow us to boot FreeBSD kernel (using uImage encapsulation) directly
from U-boot using 'bootm' command or by Android fastboot loader.
For now, kernel uImage must be marked as Linux, but we can add support for
FreeBSD into U-Boot later.
controller IPI provider.
New struct intr_ipi is defined which keeps all info about an IPI:
its name, counter, send and dispatch methods. Generic intr_ipi_setup(),
intr_ipi_send() and intr_ipi_dispatch() functions are implemented.
An IPI provider must implement two functions:
(1) an intr_ipi_send_t function which is able to send an IPI,
(2) a setup function which initializes itself for an IPI and
calls intr_ipi_setup() with appropriate arguments.
Differential Revision: https://reviews.freebsd.org/D5700
