close PR #13757, however I'm waiting on user feedback before declaring the
PR officially closed. Among other things, this improves UDP transmit
performance, and tx underruns are now detected and the TX start threshold
adjusted accordingly.
had to get the ML 6692 PHY driver working correctly, which is harder than
it sounds. "Bitrate" ThunderLAN devices should still be supported (i.e
the older 10Mbps Netflex 3/P, which use the TNETE110 chip that has no
MII support). The ThunderLAN has an internal PHY which makes things a
little complicated, but these are the basic rules:
- For devices with just the ThunderLAN, the internal PHY is used to
provide 10baseT, and 10base5/10baseT support. Autonegotiation will
work, but only with 10baseT links. The only thing that really gets
negotiated is whether the link is full or half duplex.
- For devices with the ThunderLAN and an external 10/100 PHY (like the
Compaq Netelligent 100Mbps cards, or the internal Netflex 3/P with
100Mbps upgrade daughter card), the external PHY is used for 10baseT
and 100baseTX modes. The internal PHY is still used to support
10base5/10base2, though you have to select them manual with ifconfig.
- For devices with the ThunderLAN and the ML6692 PHY, both the internal
and external PHYs are used, though it will appear as though the 6692
PHY will be used to support 10baseT and 100baseTX modes. In reality,
the internal PHY will be used for 10baseT, but this fact will be hidden
from the user. The 10base5/10base2 modes can also be selected manually
as with above.
been booted works too -- very neat. However I don't want the system to
stop for 5 seconds when the MII autoprobe is triggered in the xl and
tl drivers since that's lame. Instead, only use the hard delay when
we've been cold booted. If not, use the timeout mechanism instead.
(The SysKonnect driver doesn't use the same autonegotiation scheme, so
no change is required there.)
compiles cleanly on the Alpha. (On the alpha, the port type is an int,
not a short).
Cast a couple of pointers to ints via 'uintptr_t' rather than 'unsigned
int' since uintptr_t is long (64 bit) on Alpha, as are pointers.
#define COMPAT_PCI_DRIVER(name,data) DATA_SET(pcidevice_set,data)
.. to 2.2.x and 3.x if people think it's worth it. Driver writers can do
this if it's not defined. (The reason for this is that I'm trying to
progressively eliminate use of linker_sets where it hurts modularity and
runtime load capability, and these DATA_SET's keep getting in the way.)
- Change to the same transmit scheme as the PNIC driver.
- Dynamically set the cache alignment, and set burst size the same as
the PNIC driver in mx_init().
- Enable 'store and forward' mode by default. This is the slowest option
and it does reduce 100Mbps performance somewhat, but it's the most
reliable setting I can find. I'm more interested in having the driver
work reliably than trying to squeeze the best performance out of it.
The reason I'm doing this is that on *some* systems you may see a lot
of transmit underruns (which I can't explain: these are *fast* test
systems) and these errors seem to cause unusual and decidedly
non-tulip-like behavior. In normal 10Mbps mode, performance is fine
(you can easily saturate a 10Mbps link).
Also tweak some of the other drivers:
- Increase the size of the TX ring for the Winbond, ASIX, VIA Rhine
and PNIC drivers.
- Set a larger value for ifq_maxlen in the ThunderLAN driver. The setting
of TL_TX_LIST_CNT - 1 is too low (the ThunderLAN driver only allocates
20 transmit descriptors, and I don't want to fiddle with that now
because the ThunderLAN's descriptor structure is an oddball size
compared to the others).
the alpha. Now the ThunderLAN driver works on the alpha (both my
sample cards check out.) Update the alpha GENERIC config to include
ThunderLAN driver now that I've tested it.
- When trying to map ports, if mapping TL_PCI_LOIO or TL_PCI_LOMEM fails,
try mapping the other one. Apparently, some ThunderLAN parts swap these
two registers while others don't.
- Add support for bitrate (non-MII) PHYs. If no MII-based PHY is found,
program the chip for bitrate mode. This is required for the TNETE110
part, which doesn't have MII support. (It's also obsolete, but there
are still some people out there who have them.) With this change and the
change above, the Compaq Netflex-3/P 10baseT/BNC board works correctly.
(Thanks to Matthew Dodd for getting me one of these cards.)
- Convert to bus_space_foo() for register accesses.
- Add changes to support FreeBSD/Alpha. I still have to actually test
this in my Alpha box so I'm not going to update /sys/alpha/conf/GENERIC
yet.
address, account for cards which report the Texas Instruments PCI vendor ID
in addition to Compaq and Olicom. (I don't actually have a card that
reports the TI vendor/device ID, but it appears that some Racore adapters
work this way, and failing to account for it when we have the ID listed
in the supported devices list is a bug.)
apparently possible) event that the transmit start routine is
called with and empty if_snd queue, bail out instead of dereferencing
unilitialized transmit list pointers and panicking.
and increase the tx interrupt threshold to 4. This fixes performance
problems on slower systems.
Also fix a mind-o in the rx ring init routine: I used the TX
constant instead of the RX. This isn't a problem as long as the
rings are the same size, but if they aren't hijinx will ensue.
memory mapped mode. There are some laptop docking stations with
built-in tlan chips where memory mapped mode doesn't work correctly.
Pointed out by: jmb
PHYs in tl_attach(). This is mainly to suck away any possible stray
interrupts.
This prevents an intermittent problem on some systems where the adapter
probes correctly but yields a device timeout (and possible subsequent adapter
check) when configured. When I originally tested the driver, I ifconfig'ed
the interface after the system had already been booted and didn't notice
any problems, but when configuring the interface immediately at startup,
it would occasionally timeout and hang, until an adapter check interrupt
came along and reset things again. I'm not exactly sure if this is a
general problem of just something peculiar to this hardware (there are
three devices, including the tlan, all on IRQ 11) but the extra reset
shouldn't hurt anything. (It works fine with my 100Mbps Olicom adapter too.)
Thanks to Mark Taylor from Cybernet (mtaylor@cybernet.com) for allowing
me remote access to a Compaq system for debugging purposes.
changes:
- Cleaned up register access macros so that they work like the XL
driver macros (you can switch from PIO to memory-mapped mode
using a single #define -- default is still memory mapped mode).
The old 'struct overlayed onto the memory mapped register space'
cruft has been removed.
- Improved multicast filter code. The ThunderLAN has four entry
perfect filter table in addition to the 64-bit hash table: we need
one of the perfect filter entries for the station address, but we
can use the other three for multicast filtering. We arrange to put
the first three multicast group addresses in the perfect filter
slots so that commonly joined groups like the all hosts group and
the all routers group can be filtered without using up bits in the
hash table.
Note: in FreeBSD 3.0, multicast groups are stored in a doubly
linked list, however new entries are added at the head of the list
(thereby pushing existing entries down towards the tail). We want
to update the filter starting from the oldest entry to the newest
since the all hosts group is always joined first. This means we
really want to start from the tail of the list, not the head, but
to find the tail we first have to traverse the list all the way to
the end and then add entries working backwards. This is a bit of a
kludge and could be inefficient if the list is long.
- Cleaned up autonegotiation code: tl_autoneg() wasn't always setting
modes correctly.
- Cleaned up ifmedia update and status routines as well.
- Added tl_hardreset() routine to initialize the internal PHY according
to the ThunderLAN manual.
- Did away with the kludge where PHYs were treated as separate logical
interfaces. This didn't really work, especially in the case of the
newer Olicom 2326 adapters which use a Micro Linear ML6692 PHY which
provides only 100Mbps support, relying on the internal PHY for 10Mbps
support (both PHYs share the RJ45 port, with the 6692 doing all the
autonegotiation work). This kludge resulted from my misunderstanding
of the operation of the Compaq Netelligent Dual Port card (the tlan
manual mentions multiple channels, but in a different context; this
got me a little confused). The driver has been reported to work
correctly with the dual port card.
- Added dio_getbit/dio_setbit/dio_read/dio_write functions which carefully
set the ThunderLAN's indirectly accessed internal registers. This makes
the EEPROM reading code more reliable.
Hopefully I won't have to touch this again before 3.0 goes out the door.
I plan to import the 2.2.x version sometime this week.
Approved-by: jkh
- probe for PHYs by checking the BMSR (phy status) register instead
of the vendor ID register.
- fix the autonegotiation routine so that it figures out the autonegotiated
modes correctly.
- add tweaks to support the Olicom OC-2326 now that I've actually had
a chance to test one
o Olicom appears to encode the ethernet address in the EEPROM
in 16-bit chunks in network byte order. If we detect an
Olicom card (based on the PCI vendor ID), byte-swap the station
address accordingly.
XXX The Linux driver does not do this. I find this odd since
the README from the Linux driver indicates that patches to
support the Olicom cards came from somebody at Olicom; you'd
think if anyone would get that right, it'd be them. Regardless,
I accepted the word of the disgnoatic program that came bundled
with the card as gospel and fixed the attach routine to make
the station address match what it says.
o The version of the 2326 card that I got for testing is a
strange beast: the card does not look like the picture on
the box in which it was packed. For one thing, the picture
shows what looks like an external NS 83840A PHY, but the
actual card doesn't have one. The card has a TNETE100APCM
chip, which appears to have not only the usual internal
tlan 10Mbps PHY at MII address 32, but also a 10/100 PHY
at MII address 0. Curiously, this PHY's vendor and device ID
registers always return 0x0000. I suspect that this is
a mutant version of the ThunderLAN chip with 100Mbps support.
This combination behaves a little strangely and required the
following changes:
- The internal PHY has to be enabled in tl_softreset().
- The internal PHY doesn't seem to come to life after
detecting the 100Mbps PHY unless it's reset twice.
- If you want to use 100Mbps modes, you have to isolate
the internal PHY.
- If you want to use 10Mbps modes, you have to un-isolate
the internal PHY.
The latter two changes are handled at the end of tl_init(): if
the PHY vendor ID is 0x0000 (which should not be possible if we
have a real external PHY), then tl_init() forces the internal
PHY's BMCR register to the proper values.
cure the problems I was having with interrupts not being acknowledged
on time. This fixes a problem I observed where starting two ping -f
processes at 10Mbps would cause an adapter check due to TX GO commands
being issued before TXEOC interrupts were being acked.
Also fix a small problem with tl_start(): the mechanism I was using
to queue new packets onto the TX chain was bogus.
Change adapter check handler so that it resets card state after
tl_softreset() is stored.
Moved all EEPROM-related macro definitions into if_tlreg.h.
Don't allow an autoneg session to start until after the TX queue has
been drained, and don't transmit anything until after the autoneg
session is complete.
Also add support for two more Compaq ThunderLAN-based cards, and three
cards from Olicom which also use the ThunderLAN chip. The only thing
different about the Olicom cards is that they store the station address
at a different location within the EEPROM.
FreeBSD/alpha. The most significant item is to change the command
argument to ioctl functions from int to u_long. This change brings us
inline with various other BSD versions. Driver writers may like to
use (__FreeBSD_version == 300003) to detect this change.
The prototype FreeBSD/alpha machdep will follow in a couple of days
time.
I had a reason for doing this, but it violates the principle of least
astonishment. (At some point I may put this back but attach it to one of
the LINK flags so the behavior can be toggled on and off.)
Also replace my tl_calchash() with a much less disgusting and substantially
smaller one supplied by Bill Fenner.
These are probably generated by other PCI devices sharing the TLAN's
interrupt. The programmer's guide says to simply re-enable interrupts
and return if one of these is detected.
Prompted by bug report from: Bill Fenner
in -current is over, I'll put a 2.2.x specific version in the RELENG_2_2
branch. If somebody wants a 2.2 version of this driver now, they can check
out the previous version from CVS or ask me via e-mail.
Gee people, I didn't mean to stir up such a controversy. I just wanted
to make sure I could get this thing to work with both kernel versions
and didn't want to have to maintain two separate copies. All ya hadda
do was ask. :)
drivers here do and it also blows up in building GENERIC during
a release build if you try and include <osreldate.h> (which shot
my SNAP dead - argh!). Use __FreeBSD__ instead.
This driver supports the following cards/integrated ethernet controllers:
Compaq Netelligent 10, Compaq Netelligent 10/100, Compaq Netelligent 10/100,
Compaq Netelligent 10/100 Proliant, Compaq Netelligent 10/100 Dual Port,
Compaq NetFlex-3/P Integrated, Compaq NetFlex-3/P Integrated,
Compaq NetFlex 3/P w/ BNC, Compaq Deskpro 4000 5233MMX.
It should also support Texas Instruments NICs that use the ThunderLAN
chip, though I don't have any to test. If you've got a card that uses
the ThunderLAN chip but isn't listed in the PCI vendor/product list in
if_tl.c, try adding it and see what happens.
The driver supports any MII compliant PHY at 10 or 100Mbps speeds in
full or half duplex. (Those I've personally tested are the National
Semiconductor DP83840A (Prosignia server), the Level 1 LXT970 (Deskpro
desktop), and the ThunderLAN's internal 10baseT PHY.) Autonegotiation,
hardware multicast filtering, BPF and ifmedia support are included.
This chip is pretty fast; Prosignia servers with NCR SCSI, ThunderLAN
ethernet and FreeBSD make for a nice combination.
