to the pci attachment. Cardbus is a derived class of pci so all pci
drivers are automatically available for matching against cardbus devices.
Reviewed by: imp
aic7xxx_pci.c:
When performing our register test, be careful
to avoid resetting the chip when pausing the
controller. The test reads the HCNTRL register
and then writes it back with the PAUSE bit
explicitly set. If the last write to the controller
before our probe is to reset it, the CHIPRST
bit will still be set, so we must mask it off
before the PAUSE operation. On some chip versions,
we cannot access registers for a few 100us after
a reset, so this inadvertant reset was causing PCI
errors to occur on the read to check for paused
status.
Submitted by: gibbs
Add two new arguments to bus_dma_tag_create(): lockfunc and lockfuncarg.
Lockfunc allows a driver to provide a function for managing its locking
semantics while using busdma. At the moment, this is used for the
asynchronous busdma_swi and callback mechanism. Two lockfunc implementations
are provided: busdma_lock_mutex() performs standard mutex operations on the
mutex that is specified from lockfuncarg. dftl_lock() is a panic
implementation and is defaulted to when NULL, NULL are passed to
bus_dma_tag_create(). The only time that NULL, NULL should ever be used is
when the driver ensures that bus_dmamap_load() will not be deferred.
Drivers that do not provide their own locking can pass
busdma_lock_mutex,&Giant args in order to preserve the former behaviour.
sparc64 and powerpc do not provide real busdma_swi functions, so this is
largely a noop on those platforms. The busdma_swi on is64 is not properly
locked yet, so warnings will be emitted on this platform when busdma
callback deferrals happen.
If anyone gets panics or warnings from dflt_lock() being called, please
let me know right away.
Reviewed by: tmm, gibbs
have completed across the bus but not to the host before
processing of an exception condition (busfree, bus reset,
etc.). When flushing the controller of completed commands,
we also look for packetized commands that have completed
with good status and are stored in the "good status fifo".
The hardware will post to the good status fifo even if
data for that command is still active in a FIFO. In
one particular failure case, a command outstanding on the
bus reconnected, transferred data into a FIFO, and provided
good status while the host driver was processing an expected
busfree event (PPR message negotiation). This resulted in
an entry in the good status fifo that we completed, but
since the sequencer was paused, the data in the data FIFO
for this command had never been transferred to the host.
Once the busfree processing was complete, the sequencer
was unpaused, and the data completed its transfer to the
host. In some instances, the client for the data was notified
of the completion and attempted to view the data before
it arrived. This case only occurred during FreeBSD's
multi-target probe of the SCSI bus while some devices are
negotiating to go packetized and some devices are already
running in packetized.
The fix is to run and FIFOs active with a context in the
good status fifo to completion before completing the command
to the SCSI layer. This requies duplicating the FIFO rundown
operations in the host driver that would usually be handled
by the firmware, but there is no other alternative.
Don't blindly shutdown the SCB dma engine when restarting
the sequencer. We may be killing an operation that is
not supposed to be cancelled. The cases where we need to
shutdown these dma engines are already handled elsewhere in
the driver.
Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
Add softc flag to indicate that we have seen at
least one selection since the last bus reset or
SE/LVD bus change.
aic79xx.c:
Fix a few style nits.
In ahd_update_pending_scbs(), only touch card registers
once we have found an SCB that needs to be updated.
This removes lots of clutter from PCI traces taken of
error recovery performed by the driver.
Short circuit the first selection iocell workaround handler
if we've run once since the last bus reset or iocell change.
This also removes clutter from PCI traces.
Note if completions are pending in the qoutfifo when we dump
card state.
Add a comment in ahd_clear_critical_sections() about
our need to leave ENBUSFREE set in SIMODE1 while single
stepping.
Re-arrange some delay loops so that we always perform
a read after any register write and before the delay.
This should make the delay loop more accurate.
When completing message processing for a packetized
commention, return the controller to a state where
invalid non-packetized phases will still cause protocol
violations. These are the same operations as those
performed in the clear_target_state routine in the
firmware.
Now that we have a chip with working ABORTPENDING
support (the 7901B), comment out the automatic use
of this feature until we can adequately test it.
The previous checkin updated the bug mask for the
7901B so this code was exercised.
When resetting the bus, perform an ahd_flush_device_writes()
call so that our reset assertion delay is acurately
timed from when the reset bit is written to the controller.
Remove an old comment that no longer applies.
Fix a jump in our unexpected non-packetized phase
handler to use an explicit lable. The old code
had a hardcoded jump offset that was off by one
instruction.
Add a 7901A specific feature definition.
aic79xx_pci.c:
Split out the general aic790X setup into it's own
setup handler that works on single and dual controllers.
Adjust all other PCI setup handlers to initialize the
chips basic features and type before calling the generic
handler.
Turn off a few Rev B workarounds that are not required
on the 7901B.
of the contents of the CCSCBCTL register into our
local varaible. The other bits are used in later tests.
This avoids a potential deadlock in ahd_run_qoutfifo()
if we happen to catch the DMA engine in just the right
state.
Devices below may experience a change in geometry.
* Due to a bug, aic(4) never used extended geometry. Changes all drives
>1G to now use extended translation.
* sbp(4) drives exactly 1 GB in size now no longer use extended geometry.
* umass(4) drives exactly 1 GB in size now no longer use extended geometry.
For all other controllers in this commit, this should be a no-op.
Looked over by: scottl
if it was already enabled. We don't want to set it
when it shouldn't be set, we just don't want to
inadvertantly turn it off. This should fix a recent
report of the aic7xxx driver repeatedly complaining of
"unexpected busfree while idle" in one configuration.
successfully mapping our registers. This
avoids the disabling of memory mapped I/O
just because some other driver probe happened
to touch our registers.
This drive delays going async after receiving a WDTR
message. We now send an SDTR message after a WDTR even
if our goal is to go async. This should work even for
confused devices.
If we get an unexpected busfree when attempting a WDTR
or SDTR, only set the goal negotiation parameters we were
trying to negotiate to off. This means that should a WDTR
message fail, we will still try an SDTR if our goal is
non-async.
Fix a few more places where we were looking at goal.period
instead of goal.offset for determining if we should be
negotiating sync. This should not have any impact on
our behavior, but the offset is more definitive and should
be used.
aic79xx.c:
aic79xx.h:
aic79xx_pci.c:
aic7xxx.c:
aic7xxx.h:
aic7xxx_pci.c:
Switch ah?_reset() to take an additional "reinit" argument.
Use this instead of init_level to determin if the chip
should be fully reinitialized after a chip reset. This
is required so that ah?_shutdown() can reset the chip
without side-effects.
aic79xx.c:
Implement ahd_suspend() and ahd_resume().
aic7xxx.c:
Change ahc_loadseq() to *not* restart the sequencer.
This brings the loadseq behavior in line with that
of the 7902 driver and also simplifies the init routine.
Correct the resume routine to enable interrupts and
restart the sequencer.
Use the special LUNLEN_SINGLE_LEVEL constant for
post Rev A4 hardware for single byte luns. Without
this change, Rev B hardware would place the single
byte of lun data in byte 0 of the lun structure when
it should be in byte 1. Since there are few if any
devices on the market that support multiple luns in
target mode, the corrupted lun field (which was only
corrupted for non-zero luns) wasn't hurting us.
Approved by: re (rwatson)
aic79xx.h:
aic79xx.reg:
Return the SCB_TAG field to 16byte alignment.
It seems that on some PCI systems, SCBs are not
transferred correctly to the controller with
the previous placement of the SCB_TAG field.
Approved by: re (rwatson)
BUS_DMASYNC_ definitions remain as before. The does not change the ABI,
and reverts the API to be a bit more compatible and flexible. This has
survived a full 'make universe'.
Approved by: re (bmah)
aic79xx.c:
In ahd_handle_ign_wide_residue():
o Use SCB_XFERLEN_ODD SCB field to determine transfer
"oddness" rather than the DATA_COUNT_ODD logic.
SCB_XFERLEN_ODD is toggled on every ignore wide
residue message so that multiple ignore wide residue
messages for the same transaction are properly supported.
o If the sg list has been exausted, the sequencer
doesn't bother to update the residual data count
since it is known to be zero. Perform the zeroing
manually before calculating the remaining data count.
o Use multibyte in/out macros instead of shifting/masking
by hand.
aic79xx_inline.h:
In ahd_setup_scb_common(), setup the SCB_XFERLEN_ODD field.
aic79xx.reg:
Use the SCB_TASK_ATTRIBUTE field as a bit field in the
non-packetized case. We currently only define one bit,
SCB_XFERLEN_ODD.
Remove the ODD_SEG bit field that was used to carry the odd
transfer length information through the SG cache. This
is obviated by SCB_XFERLEN_ODD field.
Remove the DATA_COUNT_ODD scratch ram byte that was used
dynamicaly compute data transfer oddness. This is obviated
by SCB_XFERLEN_ODD field.
aic79xx.seq:
Remove all updates to the DATA_COUNT_ODD scratch ram field.
Remove all uses of ODD_SEG. These two save quite a few
sequencer instructions.
Use SCB_XFERLEN_ODD to validate the end of transfer
ignore wide residue message case.
aic7xxx.c:
In ahc_handle_ign_wide_residue():
o Use SCB_XFERLEN_ODD SCB field to determine transfer
"oddness" rather than the DATA_COUNT_ODD logic.
SCB_XFERLEN_ODD is toggled on every ignore wide
residue message so that multiple ignore wide residue
messages for the same transaction are properly supported.
o If the sg list has been exausted, the sequencer
doesn't bother to update the residual data count
since it is known to be zero. Perform the zeroing
manually before calculating the remaining data count.
o Ensure that SG_LIST_NULL is cleared in the
residual sg pointer for "mid-transfer" ignore
wide residue cases.
o Use multibyte in/out macros instead of shifting/masking
by hand.
aic7xxx.h:
Modify the SCB_GET_LUN() macro to mask the lun hardware
SCB field with LID. This leaves two bits in the LUN
field that can be used for other purposes.
aic7xxx.reg:
Change LID to be 0x3F. This is the maximum supported
lun size for non-packetized SCSI. Map the top bit
of the lun to SCB_XFERLEN_ODD. The host must set
this bit whenever a transfer is an odd length.
Remove the ODD_SEG bit field that was used to carry the odd
transfer length information through the SG cache. This
is obviated by SCB_XFERLEN_ODD field.
Remove the DATA_COUNT_ODD scratch ram byte that was used
dynamicaly compute data transfer oddness. This is obviated
by SCB_XFERLEN_ODD field.
aic7xxx.seq:
Be more careful in our handling of the SCB_LUN field. It
must be masked with LID if only lun information is desired.
Remove all updates to the DATA_COUNT_ODD scratch ram field.
Remove all uses of ODD_SEG. These two save quite a few
sequencer instructions.
Use SCB_XFERLEN_ODD to validate the end of transfer
ignore wide residue message case.
aic7xxx_inline.h:
In ahc_queue_scb(), setup the SCB_XFERLEN_ODD field.
Approved by: RE
FAILDIS in the SEQCTL register, not the HCNTRL register.
aic7xxx.c:
Remeber SEQCTL settings in the "seqctl" field of our
softc. seqctl defaults to just having FASTMODE set,
but the bus attachments can override this.
aic7xxx.h:
Add the seqctl softc field.
aic7xxx_pci.c:
Update the seqctl softc field and manually update SEQCTL
when to many PCI errors occur
Approved by: RE
to be more efficient by having the sequencer copy the
single byte of valid lun data into the long lun field.
aic79xx.c:
Memset our hardware SCB to 0 so that untouched
fields don't confuse diagnostic output. With the
old method for handling the Rev A bug, if the long
lun field was not 0, this could result in bogus
lun information being sent to drives.
Use the same SCB transfer size for all chip types
now that the long lun is not DMA'ed to the chip.
aic79xx.seq:
Add code to copy lun information for Rev.A hardware.
aic79xx_inline.h:
Remove host update of the long_lun field on every
packetized command.
Sort IDs based on chip type.
Remove IROC IDs. We'll switch to using the IROC masks
if/when we want to start attaching to IROC controllers.
Approved by: RE
Switch to handling bad SCSI status as a sequencer interrupt
instead of having the kernel proccess these failures via
the completion queue. This is done because:
o The old scheme required us to pause the sequencer and clear
critical sections for each SCB. It seems that these pause
actions, if coincident with a sequencer FIFO interrupt, would
result in a FIFO interrupt getting lost or directing to the
wrong FIFO. This caused hangs when the driver was stressed
under high "queue full" loads.
o The completion code assumed that it was always called with
the sequencer running. This may not be the case in timeout
processing where completions occur manually via
ahd_pause_and_flushwork().
o With this scheme, the extra expense of clearing critical
sections is avoided since the sequencer will only self pause
once all pending selections have cleared and it is not in
a critical section.
aic79xx.c
Add code to handle the new BAD_SCB_STATUS sequencer
interrupt code. This just redirects the SCB through
the already existing ahd_complete_scb() code path.
Remove code in ahd_handle_scsi_status() that paused
the sequencer, made sure that no selections where
pending, and cleared critical sections. Bad
status SCBs are now only processed when all of these
conditions are true.
aic79xx.reg:
Add the BAD_SCB_STATUS sequencer interrupt code.
aic79xx.seq:
When completing an SCB upload to the host, if
we are doing this because the SCB contains non-zero
SCSI status, defer completing the SCB until there
are no pending selection events. When completing
these SCBs, use the new BAD_SCB_STATUS sequencer
interrupt. For all other uploaded SCBs (currently
only for underruns), the SCB is completed via the
normal done queue. Additionally, keep the SCB that
is currently being uploaded on the COMPLETE_DMA_SCB
list until the dma is completed, not just until the
DMA is started. This ensures that the DMA is restarted
properly should the host disable the DMA transfer for
some reason.
In our RevA workaround for Maxtor drives, guard against
the host pausing us while trying to pause I/O until the
first data-valid REQ by clearing the current snapshot
so that we can tell if the transfer has completed prior
to us noticing the REQINIT status.
In cfg4data_intr, shave off an instruction before getting
the data path running by adding an entrypoint to the
overrun handler to also increment the FIFO use count.
In the overrun handler, be sure to clear our LONGJMP
address in both exit paths.
Perform a few sequencer optimizations.
aic79xx.c:
Print the full path from the SCB when a packetized
status overrun occurs.
Remove references to LONGJMP_SCB which is being
removed from firmware usage.
Print the new SCB_FIFO_USE_COUNT field in the
per-SCB section of ahd_dump_card_state(). The
SCB_TAG field is now re-used by the sequencer,
so it no longer makes sense to reference this
field in the kernel driver.
aic79xx.h:
Re-arrange fields in the hardware SCB from largest
size type to smallest. This makes it easier to
move fields without changing field alignment.
The hardware scb tag field is now down near the
"spare" portion of the SCB to facilitate reuse
by the sequencer.
aic79xx.reg:
Remove LONGJMP_ADDR.
Rearrange SCB fields to match aic79xx.h.
Add SCB_FIFO_USE_COUNT as the first byte
of the SCB_TAG field.
aic79xx.seq:
Add a per-SCB "Fifos in use count" field and use
it to determine when it is safe (all data posted)
to deliver status back to the host. The old method
involved polling one or both FIFOs to verify that
the current task did not have pending data. This
makes running down the GSFIFO very cheap, so we
will empty the GSFIFO in one idle loop pass in
all cases.
Use this simplification of the completion process
to prune down the data FIFO teardown sequencer for
packetized transfers. Much more code is now shared
between the data residual and transfer complete cases.
Correct some issues in the packetized status handler.
It used to be possible to CLRCHN our FIFO before status
had fully transferred to the host. We also failed to
handle NONPACKREQ phases that could occur should a CRC
error occur during transmission of the status data packet.
Correct a few big endian issues:
aic79xx.c:
aic79xx_inline.h:
aic79xx_pci.c:
aic79xx_osm.c:
o Always get the SCB's tag via the SCB_GET_TAG acccessor
o Add missing use of byte swapping macros when touching
hscb fields.
o Don't double swap SEEPROM data when it is printed.
Correct a big-endian bug. We cannot assign a
o When assigning a 32bit LE variable to a 64bit LE
variable, we must be explict about how the words
of the 64bit LE variable are initialized. Cast to
(uint32_t*) to do this.
aic79xx.c:
In ahd_clear_critical_section(), hit CRLSCSIINT
after restoring the interrupt masks to avoid what
appears to be a glitch on SCSIINT. Any real SCSIINT
status will be persistent and will immidiately
reset SCSIINT. This clear should only get rid of
spurious SCSIINTs.
This glitch was the cause of the "Unexpected PKT busfree"
status that occurred under high queue full loads
Call ahd_fini_scbdata() after shutdown so that
any ahd_chip_init() routine that might access
SCB data will not access free'd memory.
Reset the bus on an IOERR since the chip doesn't
seem to reset to the new voltage level without
this.
Change offset calculation for scatter gather maps
so that the calculation is correct if an integral
multiple of sg lists does not fit in the allocation
size.
Adjust bus dma tag for data buffers based on 39BIT
addressing flag in our softc.
Use the QFREEZE count to simplify ahd_pause_and_flushworkd().
We can thus rely on the sequencer eventually clearing ENSELO.
In ahd_abort_scbs(), fix a bug that could potentially
corrupt sequencer state. The saved SCB was being
restored in the SCSI mode instead of the saved mode.
It turns out that the SCB did not need to be saved at all
as the scbptr is already restored by all subroutines
called during this function that modify that register.
aic79xx.c:
aic79xx.h:
aic79xx_pci.c:
Add support for parsing the seeprom vital product
data. The VPD data are currently unused.
aic79xx.h:
aic79xx.seq:
aic79xx_pci.c:
Add a firmware workaround to make the LED blink
brighter during packetized operations on the H2A.
aic79xx_inline.h:
The host does not use timer interrupts, so don't
gate our decision on whether or not to unpause
the sequencer on whether or not a timer interrupt
is pending.
aic7xxx.h:
Split out core chip initialization into ahc_chip_init().
This will allow us to reset the chip correctly at times
other than initial chip setup.
aic7770.c
aic7xxx_pci.c:
Flesh out bus chip init methods for our two
bus attachments and use these, in addition to
bus suspend/resume hooks to get the core in
better shape for handling these events.
When disabling PCI parity error checking, use FAILDIS.
Although the chip docs indicate that clearing PERRESPEN
should also work, it does not.
Auto-disable pci parity error checking after informing
the user of AHC_PCI_TARGET_PERR_THRESH number of parity
errors observed as a target.
aic7xxx.h:
aic7xxx_pci.c
aic7770.c
aic7xxx.c
Add the instruction_ram_size softc field.
Remove the now unused stack_size softc field.
Modify ahc_loadseq to return a failure code
and to actually check the downloaded instruction
count against the limit set in our softc.
Modify callers of ahc_loadseq to handle load
failures as appropriate.
Set instruction RAM sizes for each chip type.
aic7xxx_pci.c:
Add some delay in the aic785X termination
control code. This may fix problems with
the 2930.
Be consistent in how we access config space
registers. 16bit registers are accessed using
16bit ops.
aic7xxx.c:
Correct spelling errors.
Have ahc_force_renegotiation() take a devinfo as is done
in the U320 driver. Use this argument to correct a bug
in the selection timeout handler where we forced a renegotiation
with the last device that had set SAVED_SCSIID. SAVED_SCSIID
is only updated once a selection is *sucessfull* and so is
stale for any selection timeout.
Cleanup the setup of the devinfo for busfree events. We
now use this devinfo for a call to ahc_force_renegotiation()
at the bottom of the routine, so it must be initialized in
all cases.
In ahc_pause_and_flushwork(), adjust the loop so that it
will exit in the hot-eject case even if the INT_PEND mask
is something other than 0xFF (as it is in this driver).
Correct a wrapping string constant.
Call ahc_fini_scbdata() after shutdown so that
any ahc_chip_init() routine that might access
SCB data will not access free'd memory.
Correctly setup our buffer tag to indicate that 39bit
addressing is available if in 39bit addressing mode.
Rearrange some variable declarations based on
type size.
aic7xxx.c
aic7xxx.h:
aic7xxx.reg:
Consistently use MAX_OFFSET for the user max syncrate
set from non-volatile storage. This ensures that the
offset does not conflict with AHC_OFFSET_UNKNOWN.
Change AHC_OFFSET_UNKNOWN to 0xFF. This is
a value that the curr->offset can never be,
unlike '0' which we previously used. This
fixes code that only checks for a non-zero
offset to determine if a sync negotiation
is required since it will fire in the unknown
case even if the goal is async.
Change MAX_OFFSET to 0x7f which is the max
offset U160 aic7xxx controllers can negotiate.
This ensures that curr->offset will not
match AHC_OFFSET_UNKNOWN.
aic7xxx_inline.h:
Have our inline interrupt handler return with a value
indicating whether we serviced a real interrupt. This
is required for Linux support.
Return earlier if the interrupt is not for us.
Include read streaming in the PPR flags we display in diagnostics.
In ahd_reset(), set the known mode after our initial pause prior to
setting the mode. We can't just set the mode directly because the
current mode, after the pause, is most likely unknown and setting the
mode when the saved mode is unknown will trigger an assertion in
the mode debug code.
Complete an audit for SCB RAM reads. These reads must be performed
via the special ahd_in?_scbram() methods so we can perform a
Rev A. PCI-X workaround.
Remove a superfluous mode save operation that was performed just
prior to a call to ahd_clear_critical_section(). The saved mode
was never restored and wouldn't have been valid anyway since the
mode could change while single stepping out of a critical section.
aic79xx.h:
Add new BUG definition AHD_PCIX_SCBRAM_RD_BUG.
aic79xx_inline.h:
Update ahd_inb_scbram routine to check for AHD_PCIX_SCBRAM_RD_BUG
and only apply the workaround if this bug is active. The old code
applied the workaround in all cases.
aic79xx_pci.c:
Set AHD_PCIX_SCBRAM_RD_BUG for the A4.
Remove an attempted saved_modes call in ahd_pci_test_register_access().
Saving the modes can only occur when we are paused, but the call was
happening before the chip was known to be paused. Restoring the
modes doesn't make sense either since the code makes no assumptions
about the state of the sequencer until the first time the mode is set
by the driver. This happens after the registers are successfully
mapped.
Clear the LQICRC_NLQ status should it pop up after we have
already handled the SCSIPERR. During some streaming operations
this status can be delayed until the stream ends. Without this
change, the driver would complain about a "Missing case in
ahd_handle_scsiint".
In the LQOBUSFREE handler...
Don't return the LQOMGR back to the idle state until after
we have cleaned up ENSELO and any status related to this
selection. The last thing we need is the LQO manager starting
another select-out before we have updated the execution queue.
It is not clear whether the LQOMGR would, or would not
start a new selection early.
Make sure ENSELO is off prior to clearing SELDO by flushing
device writes.
Move assignment of the next target SCB pointer inside of
an if to make the code clearer. The effect is the same.
Dump card state in both "Unexpected PKT busfree" paths.
In ahd_reset(), set the chip to SCSI mode before reading SXFRCTL1.
That register only exists in the SCSI mode. Also set the mode
explicitly to the SCSI mode after chip reset due to paranoia.
Re-arrange code so that SXFRCTL1 is restored as quickly after the
chip reset as possible.
S/G structurs must be 8byte aligned. Make this official by saying
so in our DMA tag.
Disable CIO bus stretch on MDFFSTAT if SHVALID is about to come
true. This can cause a CIO bus lockup if a PCI or PCI-X error
occurs while the stretch is occurring - the host cannot service
the PCI-X error since the CIO bus is locked out and SHVALID will
never resolve. The stretch was added in the Rev B to simplify the
wait for SHVALID to resolve, but the code to do this in the open
source sequencer is so simple it was never removed.
Consistently use MAX_OFFSET for the user max syncrate set from
non-volatile storage. This ensures that the offset does not
conflict with AH?_OFFSET_UNKNOWN.
Have ahd_pause_and_flushwork set the mode to ensure that it has
access to the registers it checks. Also modify the checking of
intstat so that the check against 0xFF can actually succeed if
the INT_PEND mask is something other than 0xFF. Although there
are no cardbus U320 controllers, this check may be needed to
recover from a hot-plug PCI removal that occurs without informing
the driver.
Fix a typo. sg_prefetch_cnt -> sg_prefetch_align. This fixes
an infinite loop at card initialization if the cacheline size is 0.
aic79xx.h:
Add AHD_EARLY_REQ_BUG bug flag.
Fix spelling errors.
Include the CDB's length just after the CDB pointer in the DMA'ed
CDB case.
Change AH?_OFFSET_UNKNOWN to 0xFF. This is a value that the
curr->offset can never be, unlike '0' which we previously used.
This fixes code that only checks for a non-zero offset to
determine if a sync negotiation is required since it will fire
in the unknown case even if the goal is async.
aic79xx.reg:
Add comments for LQISTAT bits indicating their names in the 7902
data book. We use slightly different and more descriptive names
in the firmware.
Fix spelling errors.
Include the CDB's length just after the CDB pointer in the DMA'ed
CDB case.
aic79xx.seq:
Update comments regarding rundown of the GSFIFO to reflect reality.
Fix spelling errors.
Since we use an 8byte address and 1 byte length, shorten the size
of a block move for the legacy DMA'ed CDB case from 11 to 9 bytes.
Remove code that, assuming the abort pending feature worked, would
set MK_MESSAGE in the SCB's control byte on completion to catch
invalid reselections. Since we don't see interrupts for completed
selections, this status update could occur prior to us noticing the
SELDO. The "select-out" queue logic will get confused by the
MK_MESSAGE bit being set as this is used to catch packatized
connections where we select-out with ATN. Since the abort pending
feature doesn't work on any released controllers yet, this code was
never executed.
Add support for the AHD_EARLY_REQ_BUG. Don't ignore persistent REQ
assertions just because they were asserted within the bus settle delay
window. This allows us to tolerate devices like the GEM318 that
violate the SCSI spec.
Remove unintentional settnig of SG_CACHE_AVAIL. Writing this bit
should have no effect, but who knows...
On the Rev A, we must wait for HDMAENACK before loading additional
segments to avoid clobbering the address of the first segment in
the S/G FIFO. This resolves data-corruption issues with certain
IBM (now Hitachi) and Fujitsu U320 drives.
Rearrange calc_residual to avoid an extra jmp instruction.
On RevA Silicon, if the target returns us to data-out after we
have already trained for data-out, it is possible for us to
transition the free running clock to data-valid before the required
100ns P1 setup time (8 P1 assertions in fast-160 mode). This will
only happen if this L-Q is a continuation of a data transfer for
which we have already prefetched data into our FIFO (LQ/Data
followed by LQ/Data for the same write transaction). This can
cause some target implementations to miss the first few data
transfers on the bus. We detect this situation by noticing that
this is the first data transfer after an LQ (LQIWORKONLQ true),
that the data transfer is a continuation of a transfer already
setup in our FIFO (SAVEPTRS interrupt), and that the transaction
is a write (DIRECTION set in DFCNTRL). The delay is performed by
disabling SCSIEN until we see the first REQ from the target.
Only compile in snapshot savepointers handler for RevA silicon
where it is enabled.
Handle the cfg4icmd packetized interrupt. We just need to load
the address and count, start the DMA, and CLRCHN once the transfer
is complete.
Fix an oversight in the overrun handler for packetized status
operations. We need to wait for either CTXTDONE or an overrun
when checking for an overrun. The previous code did not wait
and thus could decide that no overrun had occurred even though
an overrun will occur on the next data-valid req. Add some
comment to this section for clarity.
Use LAST_SEG_DONE instead of LASTSDONE for testing transfer
completion in the packetized status case. LASTSDONE may come up
more quickly since it only records completion on the SCSI side,
but since LAST_SEG_DONE is used everywhere else (and needs to be),
this is less confusing.
Add a missing invalidation of the longjmp address in the non-pack
handler. This code needs additional review.
aic79xx_inline.h:
Fix spelling error.
aic79xx_osm.c:
Set the cdb length for CDBs dma'ed from host memory.
Add a comment indicating that, should CAM start supporting cdbs
larger than 16bytes, the driver could store the CDB in the status
buffer.
aic79xx_pci.c:
Add a table entry for the 39320A.
Added a missing comma to an error string table.
Fix spelling errors.
Add a constant for the controller's stack size and the
maximum scsi offset.
aic7xxx.seq:
Style nit. The source is implied to be the destination
unless overridden in an "and" instruction.
Update target mode code for changes in identify seen
sequencer flags.
aic7xxx_pci.c:
Ensure that the PCIERRGENDIS bit is set in the
PCIERRGEN config space register. Perhaps this
is a reason for the spurios parity errors reported
on U160 controllers.
Honor the AHC_NO_BIOS_INIT flag.
Allow PCI interrupt reporting to be disabled,
by clearing the PERRRESEN bit in the command
register. This option is now enabled via a new
softc flag: AHC_DISABLE_PCI_PERR.
Disable SERR and pause the controller prior to performing
our mmapped I/O test. This should handle the case of
controllers that do not "auto-access pause". For legacy
controllers, use SCB ram instead of scratch ram since
the latter may contain settings left over from the BIOS
that we will use if an seeprom is not found.
Make use of new ahc_inl/outl() inlines.
aic7xxx.h:
Reformat a few comments to follow driver style.
Add a controller flags that indicate that a controller
has not been initialized by the BIOS and whether to
disable PCI parity errors..
Remove stack probing softc members.
Add a few more syncrate constants that are useful in speed
fallback calculations.
Add the SHOW_MASKED_ERRORS debug flag.
aic7xxx.h:
aic7xxx.c:
Implement the SCB_SILENT flag. This is useful for
hushing up the driver during DV or other operations
that we expect to cause transmission errors. The
messages will still print if the SHOW_MASKED_ERRORS
debug option is enabled.
aic7xxx_inline.h:
Implement ahc_[in|out][w|l|q]. This removes the need
for manual 'or and shift" type operations throughout
the driver.
aic7xxx.c:
Move SELTO dignostic so that the SCB is still valid
when we use it for printing path information.
If we are narrow, limit syncrate to Ultra2.
Don't clobber ppr_options when forcing a renegotiation.
The current ppr_options may be referenced while queuing
new commands. Don't set our width to unknown when forcing
negotiation on narrow controllers. This will confuse the
negotiation code into negotiating with a wide message on
narrow controllers.
Add an "asserting atn" diagnostic with controller/target
information.
Remove the probe_stack code. The stack is always
4 deep on legacy controllers, so probing is pointless.
This also avoids an issue where probing the stack would
upset the aic7770.
In ahc_reset(), record whether or not we found the
controller in a reset state. If the controller was
already reset, assume that no BIOS has initialized
the controller and ignore left over scratch ram
settings.
Fix an ifdef bug that caused sequencer debugging to
be enabled always.
Clear the ultraenb flag in our tstate during startup.
The ultraenbled'ness of a device is recorded in the user
transfer settings. tstate->ultraenb bitmask indicates
which devices we have negotiated an ultra speed with.
Just after initialization, we are async. Setting the
ultraenb flag while async seems to be harmless, but it
was confusing to see the ULTRAENB flag set in the SCB.
Enhance residual diagnostic to indicate if the residual
if for sense information or normal data transfers.
Indicate the features, bugs, and flags set in the softc
that are used to control firmware patch download when
booting verbose.
In ahc_dump_card_state() fix a logic reversal. The
SCSIPHASE register only exists on U160 controllers.
The SCSISIGI register exists on all controllers. Not
the other way around. Also print out the ERROR register.
Allow ahc_dump_card_state() to be called when the sequencer
is not paused. Add dump card state markers as in the U320
driver.
