Teach the dot module about the new location these includes moved to (as part
of r240684) and clean things up a bit.
Reviewed by: adrian (co-mentor)
Approved by: adrian (co-mentor)
impossible to use LQR/ECHO. They return want_magic instead.
With this change it is now possible to use
enable lqr
set lqrperiod 5
enable echo
set echoperiod 5
in your ppp.conf file.
MFC after: 3 days
- Disable the support for the second channel on twin-channel EISA cards as
the current incarnation can't possibly work correctly (it hasn't worked
since switching to new-bus where new-bus allocates the softc). If anyone
bothers to test this again it can be fixed properly and brought back.
- Use device_printf() and device_get_nameunit() instead of adv_name().
- Remove use of explicit bus space handles and tags.
- Use PCI bus accessors and helper routines rather than accessing
config registers directly.
- Handle failures from adv_attach().
Tested by: no one (hope it works)
virtqueue: Fix non-indirect virtqueues
We really must walk the entire descriptor chain in order
to append the to be free'd chain to the existing free
chain.
Submitted by: Bryan Venteicher (bryanv@daemoninthecloset.org)
Reported by: cognet
It is required to store extra recovery requests in case of bus resets.
On ATA/SATA this fixes assertion panics on HEAD with INVARIANTS enabled or
possible memory corruptions otherwise if timeout/reset happens when device
CCB queue is already full.
Reported by: gibbs@
MFC after: 1 week
This change will enable IPMI access on 5717/5718/5719/5720 and 5761
controllers. Because ASF is not available when APE firmware is
present, bge_allow_asf tunable is ignored when driver detects APE
firmware. Also bge(4) no longer performs two resets(one blind
reset and the other reset with firmware in mind) in device attach.
Now bge(4) performs a reset with enough information in bge_reset().
The APE firmware also needs special handling to make suspend/resume
work but it was not implemented yet.
With this change, bge(4) should work on any 5717/5718/5719/5720
controllers. Special thanks to Mike Hibler at Emulab who setup
remote debugging on Dell R820. Without his help I couldn't be able
to address several issues happened on Dell Rx20 systems. And many
thanks to Broadcom for continuing to support FreeBSD!
Submitted by: davidch (initial version)
H/W donated by: Broadcom
Tested by: many
Tested on: Del R820/R720/R620/R420/R320 and HP Proliant DL 360 G8
handling(jumbo, wire speed etc) in brgphy_reset(). Touching
BRGPHY_MII_AUXCTL register seems to confuse APE firmware such that
it couldn't establish a link.
BGE_PCI_PCISTATE register before issuing global reset. After
issuing reset, it reads BGE_PCI_PCISTATE register again and
compares the saved register value and current value. It was used to
know whether the global reset operation was completed or not.
Unfortunately, this logic caused several issues on recent BCM5717/
5718/5719 and BCM5720 controllers. It seems APE firmware accesses
some registers while global reset is in progress such that reading
BGE_PCI_PCISTATE register after reset does not yield old pre-reset
state value. This resulted in consuming too much time in global
reset and sometimes it couldn't successfully complete reset.
The BGE_MISCCFG_RESET_CORE_CLOCKS of BGE_MISC_CFG register is
self-clearing bit so driver is able to know the reset completion.
But the core-lock reset will disable indirect/flat/standard access
modes such that driver cannot poll BGE_MISCCFG_RESET_CORE_CLOCKS
bit of BGE_MISC_CFG register. So just wait enough time for
core-clock reset to complete.
Data sheet says driver should wait 100us for PCI/PCI-X devices and
100ms for PCIe devices. I chose 1ms for PCI/PCI-X since this value
was used for many years in bge(4). For PCIe devices, use 100ms as
recommended by data sheet.
bge_chipinit() also cleared BGE_MAC_MODE register which shall clear
firmware configured mode information. I think this will result in
losing ASF/IPMI link in device attachment. Let bge_reset() honor
firmware configured BGE_MAC_MODE register and don't announce driver
is UP in bge_reset(). Firmware should have control over driver until
it's fully initialized by driver.
While I'm here, enable workaround for PCI-X BCM5704 A0 in
bge_reset(). This will prevent internal arbitration logic from
switching to the other DMA engine after a retry cycle.
set not-NULL during SIM registration and set to UMASS_GONE on destruction.
Debug messages there look broken for at least 9 years, as they dereference
softc value that was just checked to be equal to NULL.
- Remove magic pointer value UMASS_GONE and use simple NULL instead.
Found by: Clang Static Analyzer
When creating MCAsmBackend pass the CPU string as well. In X86AsmBackend
store this and use it to not emit long nops when the CPU is geode which
doesnt support them.
Fixes PR11212.
Pull in r164133 from upstream clang trunk:
Follow up on llvm r164132.
This should prevent illegal instructions when building world on Geode
CPUs (e.g. Soekris).
MFC after: 3 days
Prevents a lockup when queried a deliberately constructed combination
of records. [CVE-2012-5166]
For more information: https://kb.isc.org/article/AA-00801
division by zero later if event timer's minimal period is above one second.
For now it is just a theoretical possibility.
Found by: Clang Static Analyzer
returns zero while request status is not CAM_REQ_CMP. That could cause
partial device attach or other unexpected results.
Found by: Clang Static Analyzer
enabled. This eliminates one mtx_lock() per each routing lookup thus improving
performance in several cases (routing to directly connected interface or routing
to default gateway).
Icmp redirects should not be used to provide routing direction nowadays, even
for end hosts. Routers should not use them too (and this is explicitly restricted
in IPv6, see RFC 4861, clause 8.2).
Current commit changes rnh_machaddr function to 'stock' rn_match (and back) for every
AF_INET routing table in given VNET instance on drop_redirect sysctl change.
This change is part of bigger patch eliminating rte locking.
Sponsored by: Yandex LLC
MFC after: 2 weeks
While here, change ISCI_LED to ISCI_PHY since conceptually the hardware
ties the LEDs to a phy and the LEDs for a given phy cannot be controlled
independently.
Submitted by: Paul Maulberger <Paul.Maulberger at gmx.de> (with modifications)
