1. rt_check() cleanup:
rt_check() is only necessary for some address families to gain access
to the corresponding arp entry, so call it only in/near the *resolve()
routines where it is actually used -- at the moment this is
arpresolve(), nd6_storelladdr() (the call is embedded here),
and atmresolve() (the call is just before atmresolve to reduce
the number of changes).
This change will make it a lot easier to decouple the arp table
from the routing table.
There is an extra call to rt_check() in if_iso88025subr.c to
determine the routing info length. I have left it alone for
the time being.
The interface of arpresolve() and nd6_storelladdr() now changes slightly:
+ the 'rtentry' parameter (really a hint from the upper level layer)
is now passed unchanged from *_output(), so it becomes the route
to the final destination and not to the gateway.
+ the routines will return 0 if resolution is possible, non-zero
otherwise.
+ arpresolve() returns EWOULDBLOCK in case the mbuf is being held
waiting for an arp reply -- in this case the error code is masked
in the caller so the upper layer protocol will not see a failure.
2. arpcom untangling
Where possible, use 'struct ifnet' instead of 'struct arpcom' variables,
and use the IFP2AC macro to access arpcom fields.
This mostly affects the netatalk code.
=== Detailed changes: ===
net/if_arcsubr.c
rt_check() cleanup, remove a useless variable
net/if_atmsubr.c
rt_check() cleanup
net/if_ethersubr.c
rt_check() cleanup, arpcom untangling
net/if_fddisubr.c
rt_check() cleanup, arpcom untangling
net/if_iso88025subr.c
rt_check() cleanup
netatalk/aarp.c
arpcom untangling, remove a block of duplicated code
netatalk/at_extern.h
arpcom untangling
netinet/if_ether.c
rt_check() cleanup (change arpresolve)
netinet6/nd6.c
rt_check() cleanup (change nd6_storelladdr)
Short description of ip_fastforward:
o adds full direct process-to-completion IPv4 forwarding code
o handles ip fragmentation incl. hw support (ip_flow did not)
o sends icmp needfrag to source if DF is set (ip_flow did not)
o supports ipfw and ipfilter (ip_flow did not)
o supports divert, ipfw fwd and ipfilter nat (ip_flow did not)
o returns anything it can't handle back to normal ip_input
Enable with sysctl -w net.inet.ip.fastforwarding=1
Reviewed by: sam (mentor)
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
drain routines are done by swi_net, which allows for better queue control
at some future point. Packets may also be directly dispatched to a netisr
instead of queued, this may be of interest at some installations, but
currently defaults to off.
Reviewed by: hsu, silby, jayanth, sam
Sponsored by: DARPA, NAI Labs
IP fast forwarding, SIOCGIFADDR, setting hardware address (not currently
enabled in cm driver), multicasts (experimental)
- add ARC_MAX_DATA, use IF_HANDOFF, remove arc_sprintf() and some unused
variables
- if_simloop logic is made more similar to ethernet
- drop not ours packets early (if we are not in promiscous mode)
Submitted by: mark tinguely (partially)
o on input don't strip the Ethernet header from packets
o input packet handling is now done with if_input
o track changes to ether_ifattach/ether_ifdetach API
o track changes to bpf tapping
o call ether_ioctl for default handling of ioctl's
o use constants from net/ethernet.h where possible
Reviewed by: many
Approved by: re
