gone rule. Optimise use of channels so that when a channel
is not ready another channel is used. Instead of using the SOF interrupt
use the system timer to drive the host statemachine. This might
give lower throughput and higher latency, but reduces the CPU usage
significantly. The DWC OTG host mode support should not be considered
for serious USB host controller applications. Some problems are still
seen with LOW speed USB devices.
of the DWC OTG is very simple in PIO mode, and we need to re-transmit
data when NAK is received among other things. We probably will need
to implement some kind of rate limitation on the NAK-ing.
The DWC OTG host mode support should still be considered
experimental. Isochronous support for DWC OTG is not
fully implemented. Some code added derives from
Aleksandr Rybalko's dotg.c driver.
"device_free_softc()" and "device_claim_softc()",
to allow USB serial drivers refcounting the softc.
These functions are used to grab the softc from
auto-free and to free the softc back to the correct
malloc type, respectivly.
Discussed with: jhb
MFC after: 2 weeks
make maintaining this driver from the documentation easier in the future.
This is a mostly mechanical change.
In uslcom_param(), move the zeroing of the final two fields of the
flowctrl structure outside of the "if CRTSCTS" section - not only were
they being zeroed in both the clauses, but these two fields have nothing
to do with hardware flow control anyway.
in SUPER-speed mode, USB 3.0.
This feature has not been tested yet, due to lack of hardware.
This feature is useful when implementing protocols like UASP,
USB attached SCSI which promises higher USB mass storage throughput.
This patch also implements support for hardware processing of endpoints
for increased performance. The switching to hardware processing
of an endpoint is done via a callback to the USB controller driver. The
stream feature is implemented like a variant of a hardware USB protocol.
USB controller drivers implementing device mode needs to be updated to
implement the new "xfer_stall" USB controller method and remove the
"xfer" argument from the "set_stall" method.
The API's toward existing USB drivers are preserved. To setup a USB transfer
in stream mode, set the "stream_id" field of the USB config structure to
the desired value.
The maximum number of BULK streams is currently hardcoded and limited to 8
via a define in usb_freebsd.h.
All USB drivers should be re-compiled after this change.
LibUSB will be updated next week to support streams mode. A new IOCTL to
setup BULK streams as already been implemented. The ugen device nodes
currently only supports stream ID zero.
The FreeBSD version has been bumped.
MFC after: 2 weeks
the device_detach() function doesn't block on UCOM device
drivers until the TTY handle is closed by the userspace
application. This is implemented by a postpone of the
softc free where the UCOM structures reside until the
TTY references are gone.
Discussed with: kib, ed
MFC after: 2 weeks
Extend the callback table of UCOM to include a
"ucom_free" function pointer which is called when
all refs on a UCOM super structure is gone.
Implement various helper functions to handle
refcounting and draining on the UCOM super
structure.
Implement macro which can be used in device
drivers to avoid module unload before all
pending TTY references are gone.
The UCOM API is backwards compatible after this
change and device drivers require no changes
to function with this change. Only a recompilation
of UCOM device drivers is required. The FreeBSD
version has been bumped in that regard.
Discussed with: kib, ed
MFC after: 2 weeks
that the wrong UART reference clock will be used for a few of the IDs.
It is currently not possible to figure that out because the Linux FTDI
driver detects this run-time and not compile time based on the bcdDevice
field of the USB device descriptor. Some of the ID's in usbdevs are not
sorted according to the product ID value. Please feel free to fix this.
I'm out of my xemacs magic today.
This syncronises us with the linux kernel at kernel.org (HEAD).
MFC after: 2 weeks
Use the interface number from the USB interface descriptor
like in the other USB serial drivers. These numbers are not
supposed to be different, though in theory they can. Make sure
that the driver then uses the interface number given by the USB
descriptor, and not the logical index of the USB stack.
For the future:
Whenever the term "index" is used in the USB code, it refers to
a number computed by the USB stack.
Whenever the term "number" is used in the USB code, it refers to
a number in a USB descriptor.
MFC after: 2 weeks
support for only the first port, but the CP2105 can have multiple ports.
Although this allowed the first port to mostly work on multi port devices,
there could be issues with this arrangement.
Update the man page to reflect support for both ports and the CP2105.
Many thanks to Silicon Labs (www.silabs.com) for providing a CP2105-EK
dev board for testing.
MFC after: 2 weeks
list of supported devices with the union of:
NetBSD src/sys/dev/usb/uslsa.c 1.18
OpenBSD src/sys/dev/usb/uslcom.c 1.24
Linux source/drivers/usb/serial/cp210x.c HEAD
Remove duplicate JABLOTRON PC60B entry.
Note that some of the devices added here are multi-port devices. The
uslcom(4) driver currently only supports the first port on such devices.
Update the man page to reflect the full list of supported devices.
Remove two caveats from the CAVEATS section, as both listed caveats no
longer apply. Add a caveat about multi-port devices.
MFC after: 2 weeks
- The USLCOM_SET_BAUD_DIV command (0x01)
- The USLCOM_SET_BAUD_RATE command (0x13)
Devices based on the CP1204 will only accept the latter command, and ignore
the former. As the latter command works on all chips that this driver
supports, switch to always using it.
A slight confusion here is that the previously used command was incorrectly
named USLCOM_BAUD_RATE - even though we no longer use it, rename it to
USLCOM_SET_BAUD_DIV to closer match the name used in the datasheet.
This change reflects a similar change made in the Linux driver, which was
submitted by preston.fick at silabs.com, and has been tested on all of the
uslcom(4) devices I have to hand.
MFC after: 2 weeks
one device (support for Motorola cables), this syncronises us with:
OpenBSD src/sys/dev/usb/uplcom.c 1.56
NetBSD src/sys/dev/usb/uplcom.c 1.73
Linux kernel.org HEAD
MFC after: 1 week
The function keys on a Microsoft Natural Egronomic Keyboard 4000 have been
repurposed as "Help", "Undo", "Redo" etc., and a special "F Lock" key is
required to return them to their normal purpose.
This change enables the UQ_KBD_BOOTPROTO quirk for the MS Natural 4000
keyboard to get the keys working again. More extensive changes to the USB
keyboard infrastructure would be needed to fully support the "F Lock" mode
and the extended keys on this keyboard.
PR: usb/116947
Approved by: hselasky@
This includes adding support for skipping FTDI interfaces used for JTAG
leaving them for userland and just attaching to the RS232 half, similarly
to how the corresponding Linux drivers handles these kind of adapters.
While at it, sort uftdi_devs and return BUS_PROBE_SPECIFIC (because
uftdi_probe() alters the instance variables for better or worse as do
other probe routines of USB drivers) instead of 0.
- Remove duplicated entries for BeagleBone.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
- Remove some stray lines.
MFC after: 3 days
Supermicro LCD screen modules seem to not support accessing reports through
the control pipes, but working fine with the interrupt pipes.
Sponsored by: iXsystems, Inc.
MFC after: 1 week
deterministically handled after the corresponding PHY drivers when
loaded as modules. Otherwise, when these MAC/PHY driver pairs are
compiled into a single module probing the PHY driver may fail. This
makes r151438 and r226154 actually work. [1]
Reported and tested by: yongari (fxp(4))
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
Submitted by: jhb [1]
MFC after: 3 days
This will give you more bandwidth for isochronous
FULL speed applications connected through a
High Speed HUB.
This patch has been tested with XHCI and EHCI.
MFC after: 1 week
and not asynchronously. This fixes problems related to USB system
suspend and resume. It is assumed that we are always allowed to sleep
from the device_suspend() method.
MFC after: 1 week
Submitted by: jkim
Code should just use the devtoname() function to obtain the name of a
character device. Also add const keywords to pieces of code that need it
to build properly.
MFC after: 2 weeks
primitives by breaking stop_scheduler into a per-thread variable.
Also, store the new td_stopsched very close to td_*locks members as
they will be accessed mostly in the same codepaths as td_stopsched and
this results in avoiding a further cache-line pollution, possibly.
STOP_SCHEDULER() was pondered to use a new 'thread' argument, in order to
take advantage of already cached curthread, but in the end there should
not really be a performance benefit, while introducing a KPI breakage.
In collabouration with: flo
Reviewed by: avg
MFC after: 3 months (or never)
X-MFC: r228424
Currently the code is not built by any modules. That will
be fixed later. The Atmel ARM bus interface file part of this
commit is just for sake of example. All registers and bits are
declared like macros and not C-structures like in official
Synopsis header files. This driver mostly origins from the
musb_otg.c driver in FreeBSD except that the chip specific
programming has been replaced by the one for DWC 2.0 USB OTG.
Some parts related to system suspend and resume have been left
like empty functions for the future. USB suspend and resume is
fully supported.
This change is designed to let USB keyboard work in the panic context
with stop_scheduler_on_panic=1. Most of change consists of removing
mtx_owned() checks where they can be easily avoided. Some additional
lock cleanup is performed along the way.
A list of the smaller changes:
- newbus methods should be executed with Giant already held, just assert
this
- kbd methods called in the non-polling context should be executed with
Giant already held, just assert this
- Giant is recursive, so we should just take it where we must have it,
without redundant checks if we already have it
- thanks to recent syscons changes we don't need to go through the hoops
to detect if kernel is going to poll us; polling mode is now clearly
separated from non-polling mode
- at present the polling mode can be entered by only one thread
- document special cases in greater detail
Please note that the ukbd code and underlying USB code still lve
dangerously in the kdb context by trying to obtain various locks
including the Giant. If any of those locks are already held by the
stopped threads, then the things would blow up.
Another limitation of the ukbd driver is that it is detached before a
system enters the halt state.
With this commit we can enable kern.stop_scheduler_on_panic by default,
that should not introduce any regressions.
Reviewed by: hselasky
MFC after: 3 months
X-MFC after: r228424, r228760
When SCHEDULER_STOPPED() is true the mtx_owned() call may return
an unexpected and thus meaningless result.
So, in the code paths that can be reached when SCHEDULER_STOPPED() is true
we need to protect the mtx_owned() calls with the SCHEDULER_STOPPED()
checks and ensure that an appropriate branch is taken in each case.
Reviewed by: hselasky
MFC after: 3 months
X-MFC after: r228424
At the moment grab and ungrab methods of all console drivers are no-ops.
Current intended meaning of the calls is that the kernel takes control of
console input. In the future the semantics may be extended to mean that
the calling thread takes full ownership of the console (e.g. console
output from other threads could be suspended).
Inspired by: bde
MFC after: 2 months
This patch should remove the need for kldunload of USB
controller drivers at suspend and kldload of USB controller
drivers at resume.
This patch also fixes some build issues in avr32dci.c
MFC after: 2 weeks
It appears this device fails if sent a SYNCHRONIZE_CACHE command, so add
quirk to avoid sending it.
I will follow up with Micron on this issue, and will adjust the quirk if
necessary based on their feedback.
Reviewed by: hselasky@
transfer statemachine. This work is about using a single
state variable instead of multiple state bits as input
for the USB statemachine to determine what to do in the
various parts of the code. No APIs towards USB device
drivers or USB host controller drivers will be changed.
MFC after: 1 month
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
to the kernel's pause() function. The pause() function can now be used
when cold != 0. Also assert that the timeout in system ticks must be
positive.
Suggested by: Bruce Evans
MFC after: 1 week
to kern/subr_bus.c. Simplify this function so that it no longer
depends on malloc() to execute. Identify a few other places where
it makes sense to use device_delete_all_children().
MFC after: 1 week
cp2103 usb-to-serial chip.
- This patch also makes the line status polling asynchronous, to reduce
the time needed to change the GPIO pins.
Submitted by: JD Louw
MFC after: 1 week
- Make it easier to port the USB code to other platforms by only using
one set of memory functions for clearing and copying memory. None of
the memory copies are overlapping. This means using bcopy() is not
required.
- Fix a compile warning when USB_HAVE_BUSDMA=0
- Add missing semicolon in avr32dci.
- Update some comments.
MFC after: 1 week
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
controller.
AX88772B data sheet does not show detailed information about
checksum offloading related things. It seems the controller has
lots of options to support checksum offloading but I failed to
understand why this feature requires so much complex controller
configuration and status bits.
One of major difference between AX88772B and its predecessor is
AX88772B uses a new RX header format when RX checksum offloading is
enabled. It also requires the received length of a frame should be
multiple of 4. Controller will pad necessary bytes to make the
length of received frame to be multiple of 4. It is driver's
responsibility to offset this pad bytes.
Note, AX88772B could be configured to get partial checksum value in
in RX header. This mode uses different RX header format and
currently we don't use that fature.
This change makes axe(4) use driver specific MII attach handler to
override uether(9)'s default MII attach and announce flow-control
capability for AX88178/AX88772A/AX88772B to PHY drivers. It seems
original AX88772 also supports flow-control but I didn't enable it
due to lack of test/access to the controller. The flow-control
threshold parameter is loaded from EEPROM and there is no way to
override this value without reprogramming EEPROM. For AX88772B,
TX/RX IP/TCP/UDP checksum offloading is announced to network stack.
IPv6 and PPPoE checksum offloading is also supported by controller
but we have no way to take advantage of these features.
Driver already knows PHY address so make PHY driver know that
information and remove unnecessary PHY address check used in
miibus_readreg/miibus_writereg callbacks. Also announce AX88178,
AX88772A and AX88772B support VLAN over-sized frame.
While I'm here clean up headers and remove axe_start() in
axe_init() because the link wouldn't be available right after media
change.
handler such that driver can announce interface capabilities and
can do its own MII attach. Currently all USB ethernet controllers
have no way to establish a link with pause capabilities. Lack of
checksum offloading support also was one of reason to bring this
change in.
This change adds a couple of wrappers to USB ethernet drivers
(uether_ifmedia_upd, uether_init and uether_start). All exported
functions in uether has prefix uether_ so I think it's more
consistent to have wrappers that follow the convention.
This change preserves ABI/KPI so it should be safe to merge this
change to stable/8.
While I'm here add missing __FBSDID and clean up headers.
Reviewed by: hselasky
Because driver is accessing a common MII structure in
mii_pollstat(), updating user supplied structure should be done
before dropping a driver lock.
Reported by: Karim (fodillemlinkarimi <> gmail dot com)
on the largest multi-write size.
From the submitter:
==
I looked further into the magic 88-byte threshold after which the bug
occurs. It turns out that figure included the 24-byte tx_desc, and up
to 64 bytes of beacon frame (header+data).
rum_write_multi doesn't seem happy with writing >64 bytes at a time to
the MAC register. If I break it up into separate calls (e.g. bytes
0-63, then bytes 64-65, written at the appropriate offset) I see the
proper beacon frames being transmitted now.
==
Submitted by: Steven Chamberlain <steven@pyro.eu.org>
MFC after: 3 days
Check for this case and just return, so that the UCOM unit number zero is
not accidentially freed.
Submitted by: Danish FreeBSD user at EuroBSDcon 2011
MFC after: 3 days
drivers that only ever attach to a particular MAC driver, i.e. inphy(4),
ruephy(4) and xlphy(4), to the directory where the respective MAC driver
lives and only compile it into the kernel when the latter is also there,
also removing it from miibus.ko and moving it into the module of the
respective MAC driver.
- While at it, rename exphy.c, which comes from NetBSD where the MAC driver
it corresponds to also is named ex(4) instead of xl(4) but that in FreeBSD
actually identifies itself as xlphy(4), and its function names accordingly
for consistency.
- Additionally while at it, fix some minor style issues like whitespace
in the register headers and add multi-inclusion protection to inphyreg.h.
CAM.
Desriptor sense is a new sense data format that originated in SPC-3. Among
other things, it allows for an 8-byte info field, which is necessary to
pass back block numbers larger than 4 bytes.
This change adds a number of new functions to scsi_all.c (and therefore
libcam) that abstract out most access to sense data.
This includes a bump of CAM_VERSION, because the CCB ABI has changed.
Userland programs that use the CAM pass(4) driver will need to be
recompiled.
camcontrol.c: Change uses of scsi_extract_sense() to use
scsi_extract_sense_len().
Use scsi_get_sks() instead of accessing sense key specific
data directly.
scsi_modes: Update the control mode page to the latest version (SPC-4).
scsi_cmds.c,
scsi_target.c: Change references to struct scsi_sense_data to struct
scsi_sense_data_fixed. This should be changed to allow the
user to specify fixed or descriptor sense, and then use
scsi_set_sense_data() to build the sense data.
ps3cdrom.c: Use scsi_set_sense_data() instead of setting sense data
manually.
cam_periph.c: Use scsi_extract_sense_len() instead of using
scsi_extract_sense() or accessing sense data directly.
cam_ccb.h: Bump the CAM_VERSION from 0x15 to 0x16. The change of
struct scsi_sense_data from 32 to 252 bytes changes the
size of struct ccb_scsiio, but not the size of union ccb.
So the version must be bumped to prevent structure
mis-matches.
scsi_all.h: Lots of updated SCSI sense data and other structures.
Add function prototypes for the new sense data functions.
Take out the inline implementation of scsi_extract_sense().
It is now too large to put in a header file.
Add macros to calculate whether fields are present and
filled in fixed and descriptor sense data
scsi_all.c: In scsi_op_desc(), allow the user to pass in NULL inquiry
data, and we'll assume a direct access device in that case.
Changed the SCSI RESERVED sense key name and description
to COMPLETED, as it is now defined in the spec.
Change the error recovery action for a number of read errors
to prevent lots of retries when the drive has said that the
block isn't accessible. This speeds up reconstruction of
the block by any RAID software running on top of the drive
(e.g. ZFS).
In scsi_sense_desc(), allow for invalid sense key numbers.
This allows calling this routine without checking the input
values first.
Change scsi_error_action() to use scsi_extract_sense_len(),
and handle things when invalid asc/ascq values are
encountered.
Add a new routine, scsi_desc_iterate(), that will call the
supplied function for every descriptor in descriptor format
sense data.
Add scsi_set_sense_data(), and scsi_set_sense_data_va(),
which build descriptor and fixed format sense data. They
currently default to fixed format sense data.
Add a number of scsi_get_*() functions, which get different
types of sense data fields from either fixed or descriptor
format sense data, if the data is present.
Add a number of scsi_*_sbuf() functions, which print
formatted versions of various sense data fields. These
functions work for either fixed or descriptor sense.
Add a number of scsi_sense_*_sbuf() functions, which have a
standard calling interface and print the indicated field.
These functions take descriptors only.
Add scsi_sense_desc_sbuf(), which will print a formatted
version of the given sense descriptor.
Pull out a majority of the scsi_sense_sbuf() function and
put it into scsi_sense_only_sbuf(). This allows callers
that don't use struct ccb_scsiio to easily utilize the
printing routines. Revamp that function to handle
descriptor sense and use the new sense fetching and
printing routines.
Move scsi_extract_sense() into scsi_all.c, and implement it
in terms of the new function, scsi_extract_sense_len().
The _len() version takes a length (which should be the
sense length - residual) and can indicate which fields are
present and valid in the sense data.
Add a couple of new scsi_get_*() routines to get the sense
key, asc, and ascq only.
mly.c: Rename struct scsi_sense_data to struct
scsi_sense_data_fixed.
sbp_targ.c: Use the new sense fetching routines to get sense data
instead of accessing it directly.
sbp.c: Change the firewire/SCSI sense data transformation code to
use struct scsi_sense_data_fixed instead of struct
scsi_sense_data. This should be changed later to use
scsi_set_sense_data().
ciss.c: Calculate the sense residual properly. Use
scsi_get_sense_key() to fetch the sense key.
mps_sas.c,
mpt_cam.c: Set the sense residual properly.
iir.c: Use scsi_set_sense_data() instead of building sense data by
hand.
iscsi_subr.c: Use scsi_extract_sense_len() instead of grabbing sense data
directly.
umass.c: Use scsi_set_sense_data() to build sense data.
Grab the sense key using scsi_get_sense_key().
Calculate the sense residual properly.
isp_freebsd.h: Use scsi_get_*() routines to grab asc, ascq, and sense key
values.
Calculate and set the sense residual.
MFC after: 3 days
Sponsored by: Spectra Logic Corporation
Import the rest of HID improvements from the branch:
- improve report descriptor parser in libusbhid to handle several kinds of
reports same time;
- add to the libusbhid API two functions wrapping respective kernel IOCTLs
for reading and writing reports;
- tune uhid IOCTL interface to allow reading and writing arbitrary report,
when multiple supported by the device;
- teach usbhidctl to set output and feature reports;
- make usbhidaction support all the same item names as bhidctl.
Sponsored by: iXsystems, inc.
This change fixes a race in device side mode during clear-stall from
host, which can cause data to be sent too early on the given
endpoint.
Approved by: re (kib)
MFC after: 1 week
patch modifies makesyscalls.sh to prefix all of the non-compatibility
calls (e.g. not linux_, freebsd32_) with sys_ and updates the kernel
entry points and all places in the code that use them. It also
fixes an additional name space collision between the kernel function
psignal and the libc function of the same name by renaming the kernel
psignal kern_psignal(). By introducing this change now we will ease future
MFCs that change syscalls.
Reviewed by: rwatson
Approved by: re (bz)
We are allocating some kilobytes of extra memory during USB device enumeration.
This does not change alot under FreeBSD, but makes sense for various embedded
operating systems using the FreeBSD USB stack, which have less memory
resources available.
Approved by: re (kib)
MFC after: 1 week
is retrieved after a failed SCSI command to continue normal
operation. Else this sense information is retrived at the next
SCSI command.
Approved by: re (kib)
Reported by: Alex Kozlov
MFC after: 1 week
PR: usb/160299
which does not support the no synchronize cache SCSI command.
The __FreeBSD_version version macro has been bumped and
external kernel modules needs to be recompiled after
this patch.
Approved by: re (kib)
MFC after: 1 week
PR: usb/160299
device having the same name like a previous one is not created before the old
one is gone. This fixes some panics due to asserts in the devfs code which
were added recently.
Approved by: re (kib)
MFC after: 1 week
ID. This fixes USB_SET_IMMED call (synchronous operation) of the uhid(4)
driver on devices with single report ID.
Reviewed by: hselasky
Approved by: re (kib)
MFC after: 1 week
coordinates, such as digitizers and touch-screens, leaving these devices
to uhid(4) and user-level. Specially patched xf86-input-mouse driver can
handle them, that isn't done and can't be done properly with ums(4)
because of mouse(4) protocol limitations.
Approved by: re (kib)
Back in 2009 I changed the ABI of the GIO_KEYMAP and PIO_KEYMAP ioctls
to support wide characters. I created a patch to add ABI compatibility
for the old calls, but I didn't get any feedback to that.
It seems now people are upgrading from 8 to 9 they experience this
issue, so add it anyway.
supports IPv4/IPv6 checksum offloading and VLAN tag insertion/
stripping as well as WOL. Because uether does not provide a way
to announce driver specific offload capabilities to upper stack,
checksum offloading support needs more work and will be done in
future.
Special thanks to ASIX for donating sample hardware.
H/W donated by: ASIX Electronics
Reviewed by: hselasky
system timer is stopped during shutdown and that the pause() statement in ukbd
causes infinite hang in this regard. The fix is to use mi_switch() instead of
pause() to do the required task switch to ensure that the required USB processes
get executed.
Reported by: Mike_Karels@mcafee.com
MFC after: 1 week
setting (either default or if supported as set by SIOCSIFFIB, e.g.
from ifconfig).
Submitted by: Alexander V. Chernikov (melifaro ipfw.ru)
Reviewed by: julian
MFC after: 2 weeks
