makefs(1) has a number of signedness warnings (when built with higher
WARNS), most of which can be addressed by careful application of casts
in makefs itself.
There is one case where a signedness warning arises from the blksize
macro, so must be addressed in the macro itself.
Reviewed by: kib, mckusick
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D10589
Background:
The same VM object might be shared by multiple processes and the
mm_struct is usually freed when a process exits.
Grab a reference on the mm_struct while the vmap is in the
linux_vma_head list in case the first process which inserted a VM
object has exited.
Tested by: kwm @
MFC after: 1 week
Sponsored by: Mellanox Technologies
operate similarly, other than not needing the delayed invalidation.
It has been tested with artificial injection of vm_page_alloc failures
while running 'sort /dev/zero'.
Reviewed by: alc, kib
MFC after: 1 week
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D10574
Increase hw.psm.synaptics.min_pressure default value from 16 to 32
to nearly match Linux driver (30-35 hysteresis loop).
This makes libinput tap detection more reliable.
Reviewed by: gonzo
Approved by: gonzo (mentor)
MFC after: 2 weeks
It is already included via sys/systm.h
Reviewed by: gonzo
Approved by: gonzo (mentor)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10266
models. This change is based on Linux driver.
Determine logical trace size. It used for calculation of touch sizes
in surface units for MT-protocol type B evdev reports.
Reviewed by: gonzo
Approved by: gonzo (mentor)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10266
Linux does. It should not affect gesture processing in current state as it
ignores finger coords on 3-finger tap detection but it should make evdev
reports looking more Linux-alike.
Reviewed by: gonzo
Approved by: gonzo
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10266
This is done with discarding pointer movements rather then mouse packets
Reviewed by: gonzo
Approved by: gonzo (mentor)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10266
Elan hw v.4 touchpads often sends touchpad release packet right after
touchpad touch one. Most probably this happens due to PS/2 limited bandwith.
Reducing of tap_min_queue size to 1 makes multifinger tap detection
more reliable in this case.
Reviewed by: gonzo
Approved by: gonzo (mentor)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10266
Wait for all advertised head packets after status packet have been received.
This fixes rare but quite annoying issue in Elan hw v.4 touchpads support
when triple-finger taps are reported as double-finger taps under several
circumstances.
Reviewed by: gonzo
Approved by: gonzo (mentor)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10266
[PPC] When restoring R30 (PIC base pointer), mark it as <def>
This happened on the PPC32/SVR4 path and was discovered when building
FreeBSD on PPC32. It was a typo-class error in the frame lowering
code.
This fixes PR26519.
Reported by: Mark Millard
PR: 206990
MFC after: 3 days
Start with some words about linear address space and its layout, then
explain pointers models and ABIs, providing explanation to the
structure of the tables.
Reviewed by: emaste, imp
'Future-proof' cheri wording by: brooks
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D10596
races at least in its ioctl handler, and at the same time it creates
device entry with 0666 permissions.
To plug possible issues in it:
- Mark it as needing Giant.
- Switch device mode to 0600.
Submitted by: C Turt
Reviewed by: imp
MFC after: 1 week
Security: Possible double free in ioctl handler
With fstyp(8) being updated to detect exfat in base r312003, it seems
like a good time to add support for auto-mounting SDXC cards -- which
use exfat by default.
The user will need to locally compile and install sysutils/fusefs-exfat
for this to succeed; logs a message to that effect when not installed.
PR: 218743
Submitted by: eborisch+FreeBSD@gmail.com
MFC after: 2 weeks
sys/cam/scsi/scsi_all.h:
Add the SCSI Solid State Media log page (0x11) structure
definition. This gives the percentage used (in terms of
lifetime flash wear) of an SSD.
MFC after: 3 days
Sponsored by: Spectra Logic
From user report, the errors are seen:
error 1
error 1
gptzfsboot: error 1 lba 4294967288
gptzfsboot: error 1 lba 1
gptzfsboot: no ZFS pools located, can't boot
The first two errors above are from issuing INT13 EAX=0x4800, meaning we
need to check if EDD is available and use EAX=0x800 if not.
For an workaround I'm using the similar idea as in biosdisk.c - first probe
ah=8h, then check if we have EDD.
Note we would like to see the correct disk size info, but we *may*
get away with anything >64MB, so we could at least test 2 zfs pool labels
on whole disk setup and not to freak out the INT13 interface.
If we get away with initial disk probing, then we have partition sizes from
the partition table and we should be able to complete the disk probing.
Note: this update does not provide full fix to all errors, but we get
the drvsize() errors removed.
Reported by: Michael W. Lucas
Reviewed by: julian
Differential Revision: https://reviews.freebsd.org/D10591
Extended attributes and their particular implementation in linux are
different from FreeBSD so in this case we have started diverging from
the UFS EA implementation, which would be the natural reference.
Depending on future progress implementing ACLs this approach may change
but for now bring to the tree an implementation that is consistent and
can be tested.
Submitted by: Fedor Uporov
Differential Revision: https://reviews.freebsd.org/D10460
After FreeBSD SVN revision 236814, the pass(4) driver changed from
only doing error recovery when the CAM_PASS_ERR_RECOVER flag was
set on a CCB to sometimes doing error recovery if the passed in
retry count was non-zero.
Error recovery would happen if two conditions were met:
1. The error recovery action was simply a retry. (Which is most
cases.)
2. The retry_count is non-zero. (Which happened a lot because of
cut-and-pasted code.)
This explains a bug I noticed in with camcontrol:
# camcontrol tur da34 -v
Unit is ready
# camcontrol reset da34
Reset of 1:172:0 was successful
At this point, there should be a Unit Attention:
# camcontrol tur da34 -v
Unit is ready
No Unit Attention.
Try it again:
# camcontrol reset da34
Reset of 1:172:0 was successful
Now set the retry_count to 0 for the TUR:
# camcontrol tur da34 -v -C 0
Unit is not ready
(pass42:mps1:0:172:0): TEST UNIT READY. CDB: 00 00 00 00 00 00
(pass42:mps1:0:172:0): CAM status: SCSI Status Error
(pass42:mps1:0:172:0): SCSI status: Check Condition
(pass42:mps1:0:172:0): SCSI sense: UNIT ATTENTION asc:29,2 (SCSI bus reset occurred)
(pass42:mps1:0:172:0): Field Replaceable Unit: 2
There is the unit attention. camcontrol(8) has a default
retry_count of 1, in case someone sets the -E flag without
setting -C.
The CAM_PASS_ERR_RECOVER behavior was only broken with the
CAMIOCOMMAND ioctl, which is the synchronous pass(4) API. It has
worked as intended (error recovery is only done when the flag
is set) in the asynchronous API (CAMIOQUEUE ioctl).
sys/cam/scsi/scsi_pass.c:
In passsendccb(), when calling cam_periph_runccb(), only
specify the error routine when CAM_PASS_ERR_RECOVER is set.
share/man/man4/pass.4:
Document that CAM_PASS_ERR_RECOVER is needed to enable
error recovery.
Reported by: Terry Kennedy <TERRY@glaver.org>
PR: kern/218572
MFC after: 1 week
Sponsored by: Spectra Logic
name and unit number in camcontrol(8).
Previously camcontrol(8) only supported rescanning or resetting
devices specified by bus:target:lun. This is because for
rescanning at least, you don't have a peripheral name and unit
number (e.g. da4) for devices that don't exist yet.
That is still the case after this change, but in other cases, when
the device does exist in the CAM EDT (Existing Device Table), we
do a careful lookup of the bus/target/lun if the user supplies a
peripheral name and unit number to find the bus:target:lun and then
issue the requested reset or rescan.
The lookup is done without actually opening the device in question,
since a rescan is often done to make a device go away after it has
been pulled. (This is especially true for busses/controllers, like
parallel SCSI controllers, that don't automatically detect changes
in topology.) Opening a device that is no longer there to
determine the bus/target/lun might result in error recovery actions
when the user really just wanted to make the device go away.
sbin/camcontrol/camcontrol.c:
In dorescan_or_reset(), if the use hasn't specified a
numeric argument, assume he has specified a device. Lookup
the pass(4) instance for that device using the transport
layer CAMGETPASSTHRU ioctl. If that is successful, we can
use the returned bus:target:lun to rescan or reset the
device.
Under the hood, resetting a device using XPT_RESET_DEV is
actually sent via the pass(4) device anyway. But this
provides a way for the user to specify devices in a more
convenient way, and can work on device rescans when the
device is going away, assuming it still exists in the EDT.
sbin/camcontrol/camcontrol.8:
Update the man page for the rescan and reset subcommands
to reflect that you can now use a device name and unit
number with them.
Sponsored by: Spectra Logic
MFC after: 3 days
vnet_pf_uninit() is called through vnet_deregister_sysuninit() and
linker_file_unload() when the pf module is unloaded. This is executed
after pf_unload() so we end up trying to take locks which have been
destroyed already.
Move pf_unload() to a separate SYSUNINIT() to ensure it's called after
all the vnet_pf_uninit() calls.
Differential Revision: https://reviews.freebsd.org/D10025
ifconfig doesn't correctly infer mlx interfaces' module names, so it will
attempt to load the mlx(4) module even when not necessary.
Reported by: rstone
MFC after: 3 weeks
X-MFC-With: 317755
Sponsored by: Spectra Logic Corp
