I am not sure what for it was done. Now open routine should automatically
fall back to read-only if open for writing is impossible. In such case
attempt to upgrade to write sounds strange.
MFC after: 1 week
This change fixes some amount of -Wsign-conversion and -Wconversion warnings
and sets correct sizes for some variables (as a result, some loop counters
were touched too).
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3763
This removes the need for manually changing this flag for Google Chrome
users. It also improves compatibility with Linux applications running under
Linuxulator compatibility layer, and possibly also helps in porting software
from Linux.
Generally speaking, the flag allows applications to create the shared memory
segment, attach it, remove it, and then continue to use it and to reattach it
later. This means that the kernel will automatically "clean up" after the
application exits.
It could be argued that it's against POSIX. However, SUSv3 says this
about IPC_RMID: "Remove the shared memory identifier specified by shmid from
the system and destroy the shared memory segment and shmid_ds data structure
associated with it." From my reading, we break it in any case by deferring
removal of the segment until it's detached; we won't break it any more
by also deferring removal of the identifier.
This is the behaviour exhibited by Linux since... probably always, and
also by OpenBSD since the following commit:
revision 1.54
date: 2011/10/27 07:56:28; author: robert; state: Exp; lines: +3 -8;
Allow segments to be used even after they were marked for deletion with
the IPC_RMID flag.
This is permitted as an extension beyond the standards and this is similar
to what other operating systems like linux do.
MFC after: 1 month
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3603
reads and writes.
PR: kern/198405
Submitted by: Matthew D. Fuller <fullermd at over-yonder dot net>
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3679
* Shuffle the kernel to be at the beginning
* Give the kernel 2mb, the rootfs 6mb, and 'mib0' the rest
* put the cfg parition just before the ART calibration data for the
wifi part in the SoC
* .. and make sure ART points to the right 64k region.
I've updated the freebsd-wifi-build wiki the instructions on using this.
If someone has an AP135 with 8MB SPI flash then this won't work; everything
minus the big mib0 partition is just a bit over 8MB. Come see me if this
ever happens (you'll likely just have to shrink the rootfs and the kernel
a little in order to make it fit.)
Tested:
* AP135 reference board.
This is roughly the iw_cxgbe equivalent of
be13b2dff8
-----------------
RDMA/cxgb4: Connect_request_upcall fixes
When processing an MPA Start Request, if the listening endpoint is
DEAD, then abort the connection.
If the IWCM returns an error, then we must abort the connection and
release resources. Also abort_connection() should not post a CLOSE
event, so clean that up too.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
-----------------
Submitted by: Krishnamraju Eraparaju at chelsio dot com.
This was off because the net80211 aggregation code was using the same
state pointers for both fast frames and ampdu tx support which led to some
pretty unfortunate panic-y behaviour.
Now that net80211 doesn't panic, let's flip this back on.
It doesn't (yet) do the horrific sounding thing of A-MPDU aggregates
of fast frames; that'll come next. It's a pre-requisite to supporting
AMSDU + AMPDU anyway, which actually speeds things up quite considerably
(think packing lots of little ACK frames into a single AMSDU.)
Tested:
* QCA955x SoC, AP mode
* AR5416, STA mode
* AR9170, STA mode (with local fast frame patches)
these functions are thin wrappers around calling the hardware-layer driver,
but some of them do sanity checks and return an error. Since the hardware
layer can only return IIC_Exxxxx status values, the iicbus helper functions
must also adhere to that, so that drivers at higher layers can assume that
any non-zero status value is an IIC_Exxxx value that provides details about
what happened at the hardware layer (sometimes those details are important
for certain slave drivers).
errno values that are at least vaguely equivelent. Also add a new status
value, IIC_ERESOURCE, to indicate a failure to acquire memory or other
required resources to complete a transaction.
The IIC_Exxxxxx values are supposed to communicate low-level details of the
i2c transaction status between the lowest-layer hardware driver and
higher-layer bus protocol and device drivers for slave devices on the bus.
Most of those slave drivers just return all status values from the lower
layers directly to their callers, resulting in crazy error reporting from a
user's point of view (things like timeouts being reported as "no such
process"). Now there's a helper function to make it easier to start
cleaning up all those drivers.
Make it clearer what each one means in the comments that define them.
IIC_BUSBSY was used in many places to mean two different things, either
"someone else has reserved the bus so you have to wait until they're done"
or "the signal level on the bus was not in the state I expected before/after
issuing some command".
Now IIC_BUSERR is used consistantly to refer to protocol/signaling errors,
and IIC_BUSBSY refers to ownership/reservation of the bus.
one specific problem: the driver didn't check for ACK/NAK after writing a
slave address byte to the bus, and some slaves signal that they are busy
(such as when completing an internal write to flash memory) by sending a
NAK in response to being addressed.
While working on that problem I discovered that the driver's handling of
error conditions in general didn't match the state transition diagram in
the reference manual, and making that right resulted in a lot of code
reorganization.
Along the way various other changes also happened...
- Remove a mutex that wasn't protecting anything.
- Remove some mystery DELAY()s, document the few that remain.
- Use pause_sbt(9) to yield the processor for the bulk of the time it
takes to transfer each byte rather than busy-polling the whole time.
- Disable the controller when no transfers are in progress; since we
don't operate in slave mode, there's no reason to run the hardware.
- Remove a bunch of unecessary code from probe().
Simplifying maintainance and options (only one place to deal with MK_DMAGENT)
This also makes packaging base less intrusive by getting a single point where
to add tags.
with the current behaviour of calling "distribution" in the etc target.
This allows mergemaster/etcupdate to still work when some configuration will be
moved to be handled in the same directories their source code lives in.
perform a stop operation on the bus if there was an error, otherwise the
bus will remain hung forever. Consistantly use 'if (error != 0)' style in
the function.
Enable and fix warnings during the build.
Although CMake adds warning flags, they are ignored in the libc++ headers
because the headers '#pragma system header' themselves.
This patch disables the system header pragma when building libc++ and fixes
the warnings that arose.
The warnings fixed were:
1. <memory> - anonymous structs are a GNU extension
2. <functional> - anonymous structs are a GNU extension.
3. <__hash_table> - Embedded preprocessor directives have undefined behavior.
4. <string> - Definition is missing noexcept from declaration.
5. <__std_stream> - Unused variable.
This should fix building world (in particular libatf-c++) with -std=c++11.
Reported by: Oliver Hartmann <ohartman@zedat.fu-berlin.de>
Without this, the signals are shown seemingly randomly in the output before
the final summary is shown. This is especially noticeable when there is
not much output from the application being traced.
Discussed with: jhb
Relnotes: yes
[SLP] Vectorize for all-constant entries.
This should fix libc++'s iostream initialization SIGBUSing on amd64,
whenever the global cout symbol is not aligned to 16 bytes.
Some further explanation: libc++'s iostream.cpp contains the definitions
of std::cout, std::cerr and so on. These global objects are effectively
declared with an alignment of 8 bytes. When an executable is linked
against libc++.so, it can sometimes get a copy of the global object,
which is then at the same alignment.
However, with clang 3.7.0, the initialization of these global objects
will incorrectly use SSE instructions (e.g. movdqa), whenever the
optimization level is high enough, and SSE is enabled, such as on amd64.
When any of these objects is not aligned to 16 bytes, this will result
in a SIGBUS during iostream initialization. In contrast, clang 3.6.x
and earlier took the 8 byte alignment into consideration, and avoided
SSE for those particular operations.
After bisecting of upstream changes, I found that the above revision
caused the change of this behavior, so I am reverting it now as a
workaround, while a discussion and test case is being prepared for
upstream.
