- Alignment issues:
* Add missing __packed attributes + padding across all drivers; in
most places there was an assumption that padding will be always
minimally suitable; in few places - e.g., in urtw(4) / rtwn(4) -
padding was just missing.
* Add __aligned(8) attribute for all Rx radiotap headers since they can
contain 64-bit TSF timestamp; it cannot appear in Tx radiotap headers, so
just drop the attribute here. Refresh ieee80211_radiotap(9) man page
accordingly.
- Since net80211 automatically updates channel frequency / flags in
ieee80211_radiotap_chan_change() drop duplicate setup for these fields
in drivers.
Tested with Netgear WG111 v3 (urtw(4)), STA mode.
MFC after: 2 weeks
Mainly focus on files that use BSD 3-Clause license.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
connectivity interact with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to pluknet@, Oliver Hartmann,
Olivier Cochard, gjb@, mmoll@, op@ and lev@, who also participated in
testing.
Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
* 286410
* 286413
* 286416
The initial commit broke a variety of debug and features that aren't
in the GENERIC kernels but are enabled in other platforms.
with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to Olivier Cochard, gjb@, mmoll@,
op@ and lev@, who also participated in testing. Details here:
https://wiki.freebsd.org/projects/ifnet/net80211
Still, drivers: ndis, wtap, mwl, ipw, bwn, wi, upgt, uath were not
tested. Changes to mwl, ipw, bwn, wi, upgt are trivial and chances
of problems are low. The wtap wasn't compilable even before this change.
But the ndis driver is complex, and it is likely to be broken with this
commit. Help with testing and debugging it is appreciated.
Differential Revision: D2655, D2740
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
This framework allows drivers to abstract the rate control algorithm and
just feed the framework with the usable parameters. The rate control
framework will now deal with passing the parameters to the selected
algorithm. Right now we have AMRR (the default) and RSSADAPT but there's
no way to select one with ifconfig, yet.
The objective is to have more rate control algorithms in the net80211
stack so all drivers[0] can use it. Ideally, we'll have the well-known
sample rate control algorithm in the net80211 at some point so all
drivers can use it (not just ath).
[0] all drivers that do rate control in software, that is.
Reviewed by: bschmidt, thompsa, weyongo
MFC after: 1 months
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
Broadcom BCM43xx chipsets. This driver uses the v3 firmware that
needs to be fetched separately. A port will be committed to create
the bwi firmware module.
The driver matches the following chips: Broadcom BCM4301, BCM4307,
BCM4306, BCM4309, BCM4311, BCM4312, BCM4318, BCM4319
The driver works for 802.11b and 802.11g.
Limitations:
This doesn't support the 802.11a or 802.11n portion of radios.
Some BCM4306 and BCM4309 cards don't work with Channel 1, 2 or 3.
Documenation for this firmware is reverse engineered from
http://bcm.sipsolutions.net/
V4 of the firmware is needed for 11a or 11n support
http://bcm-v4.sipsolutions.net/
Firmware needs to be fetched from a third party, port to be committed
# I've tested this with a BCM4319 mini-pci and a BCM4318 CardBus card, and
# not connected it to the build until the firmware port is committed.
Obtained from: DragonFlyBSD, //depot/projects/vap
Reviewed by: sam@, thompsa@
