Add support for the "snps,dis_rxdet_inp3_quirk" quirk needed
at least on SolidRun's HoneyComb.
Reviewed by: manu, mw
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D32921
Currently, to support 64-byte contexts, xhci_ctx_[gs]et_le(32|64) take a
pointer to the field within a 32-byte context and, if 64-byte contexts
are in use, compute where the 64-byte context field is and use that
instead by deriving a pointer from the 32-byte field pointer. This is
done by exploiting a combination of 64-byte contexts being the same
layout as their 32-byte counterparts, just with 32 bytes of padding at
the end, and that all individual contexts are either in a device
context or an input context which itself is page-aligned. By masking out
the low 4 bits (which is the offset of the field within the 32-byte
contxt) of the offset within the page, the offset of the invididual
context within the containing device/input context can be determined,
which is itself 32 times the number of preceding contexts. Thus, adding
this value to the pointer again gets 64 times the number of preceding
contexts plus the field offset, which gives the offset of the 64-byte
context plus the field offset, which is the address of the field in the
64-byte context.
However, this involves a fair amount of lying to the compiler when
constructing these intermediate pointers, and is rather difficult to
reason about. In particular, this is problematic for CHERI, where we
compile the kernel with subobject bounds enabled; that is, unless
annotated to opt out (e.g. for C struct inheritance reasons where you
need to be able to downcast, or containerof idioms), a pointer to a
member of a struct is a capability whose bounds only cover that field,
and any attempt to dereference outside those bounds will fault,
protecting against intra-object buffer overflows. Thus the pointer given
to xhci_ctx_[gs]et_le(32|64) is a capability whose bounds only cover the
field in the 32-byte context, and computing the pointer to the 64-byte
context field takes the address out of bounds, resulting in a fault when
later dereferenced.
This can be cleaned up by using a different abstraction. Instead of
doing the 32-byte to 64-byte conversion on access to the field, we can
do the conversion when getting a pointer to the context itself, and
define proper 64-byte versions of contexts in order to let the compiler
do all the necessary arithmetic rather than do it manually ourselves.
This provides a cleaner implementation, works for CHERI and may even be
slightly more performant as it avoids the need to mess with masking
pointers (which cannot in the general case be optimised by compilers to
be reused across accesses to different fields within the same context,
since it does not know that the contexts are over-aligned compared with
the C ABI requirements).
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D32554
When EVDEV_SUPPORT was introduced, the USB transfers may be running
after the main FIFO is closed. In connection to this a race may appear
which can lead to use-after-free scenarios. Fix this for all FIFO
consumers by initializing and resetting the FIFO queues under the
lock used by the client. Then the client driver will see an empty
queue in all cases a race may appear.
Found by: pho@
MFC after: 1 week
Sponsored by: NVIDIA Networking
While IEEE80211_R_BAND was defined, there was no place to store the
band. Add a field for that, adjust ieee80211_lookup_channel_rxstatus()
to require it, and update drivers passing "R_{FREQ|IEEE}" in already to
provide the band as well. For the moment keep the fall-back code
requiring all three fields.
Sponsored by: The FreeBSD Foundation
MFC after: 3 days
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D30662
Change the probe return value from BUS_PROBE_DEFAULT to BUS_PROBE_GENERIC
given this is the "generic" attach method. This allows individual
drivers using XHCI generic but needing their own intialisation to
gain priority for attaching over the generic implementation.
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D32257
When a usb device is detached, usb_pc_dmamap_destroy() called
bus_dmamap_destroy() while the map was still loaded. That's harmless on x86
architectures, but on all other platforms it causes bus_dmamap_destroy() to
return EBUSY and leak away any memory resources (including bounce buffers)
associated with the mapping, as well as any allocated map structure itself.
This change introduces a new is_loaded flag to the usb_page_cache struct to
track whether a map is loaded or not. If the map is loaded,
bus_dmamap_unload() is called before bus_dmamap_destroy() to avoid leaking
away resources.
MFC after: 7 days
Differential Revision: https://reviews.freebsd.org/D32208
We can now set promisc and allmulti modes.
Filtering of given multicast addresses is not supported.
Changing the mode is done by sending a command described in:
"USB CDC Subclass Specification for Ethernet Devices v1.2, section 6.2.4".
This means that at least in theory this feature should work with all
modems that are using this driver.
This fixes Huawei E3372h-320 running new firmware in "HiLink" mode.
Previously it would reset a few seconds after its mode was changed
with "usb_modeswitch".
Setting RX filter to default value at the end of attach function
fixed that.
Sponsored by: Stormshield
Obtained from: Semihalf
Differential revision: https://reviews.freebsd.org/D31766
MFC after: 2 weeks
Reviewed by: hps
After switching the dongle to the Huawei alternate mode(modem mode)
with usb_modeswitch the serial interfaces had all of their ids set to
0xFF.
After modifying umodem to work with that it attached successfully and
I've managed to configure device with standard AT commands to get
internet connection.
folder, only keeping the zero length packet API introduced in sys/dev/usb
after more reports of USB serial devices not supporting ZLPs.
Reported by: mav@
MFC after: 1 week
Sponsored by: NVIDIA Networking
port devices. If it gets eaten it is fine. Many USB device side implementations
don't properly support the clear endpoint halt command and if they do, data is lost
because the transmit FIFO is typically reset when this command is received.
Tested by: jmg
MFC after: 1 week
Sponsored by: NVIDIA Networking
xpt_bus_register and xpt_bus_deregister returns a hybrid error that's
neither a cam_status, nor an errno, but a mix of both. Update
xpt_bus_register and xpt_bus_deregister to return an errno. The vast
majority of current users compare against zero, which can also be
spelled CAM_SUCCESS. Nobody uses CAM_FAILURE, so remove that symbol
to prevent comfusion (nothing returns it either).
Where the return value is saved, ensure that the variable 'error' is
used to store an errno and 'status' is used to store a cam_status where
it makes the code clearer (usually just in functions that already mix
and match). Where the return value isn't used at all, avoid storing it
at all.
Reviewed by: scottl@, mav@ (earlier version)
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D30860
This makes it more usable in that dhclient will autolaunch from devd
now when cdce devices are plugged in.. It also sets the baudrate, but
this isn't exported via tools, and CDCE doesn't have a good way to
specify the media type, so there isn't a good way to tell userland
what the speed is currently...
Reviewed by: hps
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D30625
Now that the upper layers all go through a layer to tie into these
information functions that translates an sbuf into char * and len. The
current interface suffers issues of what to do in cases of truncation,
etc. Instead, migrate all these functions to using struct sbuf and these
issues go away. The caller is also in charge of any memory allocation
and/or expansion that's needed during this process.
Create a bus_generic_child_{pnpinfo,location} and make it default. It
just returns success. This is for those busses that have no information
for these items. Migrate the now-empty routines to using this as
appropriate.
Document these new interfaces with man pages, and oversight from before.
Reviewed by: jhb, bcr
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D29937
Use the accessor function to get the softc for this sim. This also drops
an unneeded cast.
Sponsored by: Netflix
Reviewed by: mav@, hselasky@
Differential Revision: https://reviews.freebsd.org/D30360
The second set of USB transfer is requested by hkbd(4) and
should improve HID keyboard handling in kdb and panic contexts.
MFC after: 1 week
Reviewed by: hselasky
Differential revision: https://reviews.freebsd.org/D30486
Which happens when USB transfer setup is failed.
MFC after: 1 week
PR: 254974
Reviewed by: hselasky
Differential revision: https://reviews.freebsd.org/D30485
This fixes inability to start USB xfers in a case when FIFO has been
already open()-ed but no read() or poll() calls has been issued yet.
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D30343
This fixes lose of evdev events after moused has been killed.
While here use bitwise operations for UMS_EVDEV_OPENED flag.
Reviewed by: hselasky
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D30342
behind USB HUBs are detected and the USB reset counter logic will kick in
preventing enumeration of continuously failing ports.
Submitted by: phk@
Tested by: bz@
PR: 237666
MFC after: 1 week
Sponsored by: Mellanox Technologies // NVIDIA Networking
says it should be max 10 milliseconds.
This may fix some USB enumeration issues:
> usbd_req_re_enumerate: addr=3, set address failed! (USB_ERR_IOERROR, ignored)
> usbd_setup_device_desc: getting device descriptor at addr 3 failed,
Found by: Zhichao1.Li@dell.com
MFC after: 1 week
Sponsored by: Mellanox Technologies // NVIDIA Networking
0 milliseconds and 2 seconds inclusivly. Some style fixes while at it.
The USB specification has minimum values and maximum values,
and not only minimum values.
MFC after: 1 week
Sponsored by: Mellanox Technologies // NVIDIA Networking
Since then, the FreeBSD USB stack has got proper USB RNDIS support.
PR: 254345
MFC after: 1 week
Sponsored by: Mellanox Technologies // NVIDIA Networking
similarly to the Linux driver, by a tunable read only sysctl.
Submitted by: Oleg Sidorkin <osidorkin@gmail.com>
PR: 254884
MFC after: 1 week
Sponsored by: Mellanox Technologies // NVIDIA Networking
- Make frontends call unified CTL core method ctl_datamove_done()
to report move completion. It allows to reduce code duplication
in differerent backends by accounting DMA time in common code.
- Add to ctl_datamove_done() and be_move_done() callback samethr
argument, reporting whether the callback is called in the same
context as ctl_datamove(). It allows for some cases like iSCSI
write with immediate data or camsim frontend write save one context
switch, since we know that the context is sleepable.
- Remove data_move_done() methods from struct ctl_backend_driver,
unused since forever.
MFC after: 1 month
Ignore fantom keyboard state reports entirelly rather than ignore
RollOver states for each key separatelly. Latter results in spurious
release/push pairs of events on each fantom keyboard state report.
Reported by: Jan Martin Mikkelsen <janm_AT_transactionware_DOT_com>
Submitted by: Jan Martin Mikkelsen (initial version)
PR: 253249
MFC after: 1 week
This adds a new sysctl to Wellspring Touchpad driver for controlling
Z-Axis (2-finger vertical scroll) direction "hw.usb.wsp.z_invert".
Submitted by: James Wright <james.wright_AT_digital-chaos_DOT_com>
Reviewed by: wulf
PR: 253321
Differential revision: https://reviews.freebsd.org/D28521
usbhid(4) is disabled by default to avoid conflicts with existing USB HID
drivers. To enable it place following lines to /boot/loader.conf:
hw.usb.usbhid.enable=1
usbhid_load="YES"
Suggested by: jhb
Reviewed by: hselasky
Differential revision: https://reviews.freebsd.org/D28124
When detaching the if_ure(4) driver, the TX active USB transfer array may
point to freed USB transfers. Given that the number of USB transfers is
very low, simply start all transfers every time there is a packet to
keep safe from use-after-free.
PR: 252608
MFC after: 1 week
Sponsored by: Mellanox Technologies // NVIDIA Networking
which installs /dev/uhid# alias to hidraw character device for
compatibility with some existing uhid(4) users like Firefox.
As side effect it renames traditional uhid(4) driver to hidraw
to make possible using of common unit number allocator.
Requested by: Greg V <greg_unrelenting.technology>
Reviewed by: hselasky (as part of D27992)
This driver provides raw access to HID devices through uhid(4)-compatible
interface and is based on pre-8.x uhid(4) code. Unlike uhid(4) it does
not take devices in to monopoly ownership and allows parallel access
from other drivers.
hidraw supports Linux's hidraw-compatible interface as well.
Reviewed by: hselasky
Differential revision: https://reviews.freebsd.org/D27992
This change implements hid_if.m methods for HID-over-USB protocol [1].
Also, this change adds USBHID_ENABLED kernel option which changes
device_probe() priority and adds/removes PnP records to prefer usbhid
over ums, ukbd, wmt and other USB HID device drivers and vice-versa.
The module is based on uhid(4) driver. It is disabled by default for
now due to conflicts with existing USB HID drivers.
[1] https://www.usb.org/sites/default/files/hid1_11.pdf
Reviewed by: hselasky
Differential revision: https://reviews.freebsd.org/D27893
Also hide shim code added in a previous commit under COMPAT_USBHID12.
Note: it is enough to add -DCOMPAT_USBHID12 to CFLAGS to compile old
code with new HID subsystem, but it is not enough to link it at runtime.
HID dependency has to be added explicitly with MODULE_DEPEND macro.
Reviewed by: manu, hselasky (as part of D27887)
This does an import of quirk stubs, debugging macros from USB code and
numerous usage constants used by dependent drivers.
Besides, this change renames some functions to get a better matching
with userland library and NetBSD/OpenBSD HID code. Namely:
- Old hid_report_size() renamed to hid_report_size_max()
- New hid_report_size() calculates size of given report rather than
maximum size of all reports.
- hid_get_data_unsigned() renamed to hid_get_udata()
- hid_put_data_unsigned() renamed to hid_put_udata()
Compat shim functions are provided in usbhid.h to make possible compile
of legacy code unmodified after this change.
Reviewed by: manu, hselasky
Differential revision: https://reviews.freebsd.org/D27887
It will be used by the upcoming HID-over-i2C implementation. Should be
no-op, except hid.ko module dependency is to be added to affected drivers.
Reviewed by: hselasky, manu
Differential revision: https://reviews.freebsd.org/D27867
hid_locate() currently ignores all HID items which tagged as constant,
i.e. bit 0 of main item data is set to 1. See p.6.2.2.4 of
hid1_11.pdf [1]. Such an items are unconditionally treated as
byte-alignment padding. While that may be right decision for input and
output reports that is wrong for features reports. Feature reports can
contain constant capabilities e.g. 'Contact Count Maximum'.
See: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=232040
Remove check for constant from hid_locate() to make possible parsing of
such a reports.
[1] https://www.usb.org/sites/default/files/documents/hid1_11.pdf
Reviewed by: hselasky
Obtained from: sysutils/iichid
Differential Revision: https://reviews.freebsd.org/D27747
Code changes in this commit were obtained from straight from OpenBSD's
uplcom.c with almost no modification, the list of chip names and USB
IDs was obtained from Linux.
Differential Revision: https://reviews.freebsd.org/D27952
Submitted by: tomli_tomli.me (Yifeng Li)
MFC after: 1 week
Sponsored by: Mellanox Technologies // NVIDIA Networking
The firmware header loaded into an rsu(4) device has to be customized
to reflect device settings. The driver was overwriting the header
from the shared firmware image before sending it to the device. If
two devices attached at the same time with different settings, one
device could potentially get a corrupted header. The recent changes
in a095390344 exposed this bug in the
form of a panic as the firmware blobs are now marked read-only in
object files and mapped read-only by the kernel.
To avoid the bug, change the driver to allocate a copy of the firmware
header on the stack that is initialized before writing it to the
device.
PR: 252163
Reported by: vidwer+fbsdbugs@gmail.com
Tested by: vidwer+fbsdbugs@gmail.com
Reviewed by: hselasky, bz, emaste
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D27850
If LED state is set through evdev interface, than asynchronous nature
of USB transfer callback can lead to change of order of events echoed
back to userland as it causes LED events to be echoed with some lag.
Fix that with echoing of LED events synchronously in ioctl handler.
Reviewed by: hselasky
Obtained from: sysutils/iichid
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D27750
Unlike AT keyboards, HID devices are able to send all pc105 key
states within a single report. Let evdev to transmit all key state
changes within a single report too.
Reviewed by: hselasky
Obtained from: sysutils/iichid
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D27749
Add support for LAN found on Thinkpad USB-C and Thunderbolt Gen 2
docking stations.
Submitted by: ali.abdallah@suse.com
MFC after: 1 week
Sponsored by: Mellanox Technologies // NVIDIA Networking
Hardware timestamp reporting is disabled by default as it produces many
extra events which are not handled by consumers like libinput.
Add hw.usb.wmt.timestamps=1 tunable to loader.conf to enable it.
Obtained from: sysutils/iichid
In Hybrid mode, the number of contacts that can be reported in one
report is less than the maximum number of contacts that the device
supports. For example, a device that supports a maximum of 4
concurrent physical contacts, can set up its top-level collection to
deliver a maximum of two contacts in one report. If four contact
points are present, the device can break these up into two serial
reports that deliver two contacts each.
Obtained from: sysutils/iichid
These Mini-Box LCDs are using Microchip components and sub-licensed product
IDs. Whilst here, update the constant names and descriptions for the products
to use the names listed on the manufacturer's website rather than vague ones.
The picoLCD 4x20 is named that on the manufacturer's website so prefer that
name, even though linux-usb.org lists it with the numbers reversed as one might
expect.
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D27670
- Use a uintptr_t cast to get the virtual address of a pointer in
USB_P2U() instead of a ptrdiff_t.
- Add offsets to a char * pointer directly without roundtripping the
pointer through a ptrdiff_t in USB_ADD_BYTES().
Reviewed by: imp, hselasky
Obtained from: CheriBSD
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D27581
Move initialization of num_altsetting under USB_CFG_INIT, else
there will be a page fault when enumerating USB devices.
PR: 251856
MFC after: 1 week
Submitted by: Ma, Horse <Shichun.Ma@dell.com>
Sponsored by: Mellanox Technologies // NVIDIA Networking
Allow setting the alternate interface number to fail when there is only
one alternate setting present, to comply with the USB specification.
Refactor how iface->num_altsetting is computed.
Bump the __FreeBSD_version due to change of core USB structure.
PR: 251856
MFC after: 1 week
Submitted by: Ma, Horse <Shichun.Ma@dell.com>
Sponsored by: Mellanox Technologies // NVIDIA Networking
Limit the number of alternate settings to 256.
Else the alternate index variable may wrap around.
PR: 251856
MFC after: 1 week
Submitted by: Ma, Horse <Shichun.Ma@dell.com>
Sponsored by: Mellanox Technologies // NVIDIA Networking
Some USB WLAN devices have "on-board" storage showing up as umass
and making the root mount wait for a very long time.
The WLAN drivers know how to deal with that an issue an eject
command later when attaching themselves.
Introduce a quirk to not probe these devices as umass and avoid
hangs and confusion altogether.
Reviewed by: hselasky, imp
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D27434
Replace MAXPHYS by runtime variable maxphys. It is initialized from
MAXPHYS by default, but can be also adjusted with the tunable kern.maxphys.
Make b_pages[] array in struct buf flexible. Size b_pages[] for buffer
cache buffers exactly to atop(maxbcachebuf) (currently it is sized to
atop(MAXPHYS)), and b_pages[] for pbufs is sized to atop(maxphys) + 1.
The +1 for pbufs allow several pbuf consumers, among them vmapbuf(),
to use unaligned buffers still sized to maxphys, esp. when such
buffers come from userspace (*). Overall, we save significant amount
of otherwise wasted memory in b_pages[] for buffer cache buffers,
while bumping MAXPHYS to desired high value.
Eliminate all direct uses of the MAXPHYS constant in kernel and driver
sources, except a place which initialize maxphys. Some random (and
arguably weird) uses of MAXPHYS, e.g. in linuxolator, are converted
straight. Some drivers, which use MAXPHYS to size embeded structures,
get private MAXPHYS-like constant; their convertion is out of scope
for this work.
Changes to cam/, dev/ahci, dev/ata, dev/mpr, dev/mpt, dev/mvs,
dev/siis, where either submitted by, or based on changes by mav.
Suggested by: mav (*)
Reviewed by: imp, mav, imp, mckusick, scottl (intermediate versions)
Tested by: pho
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D27225
