linkers no longer raise an error when undefined weak symbols are
found, but relocate as if the symbol value was 0. Note that we do not
repeat the mistake of userspace dynamic linker of making the symbol
lookup prefer non-weak symbol definition over the weak one, if both
are available. In fact, kernel linker uses the first definition
found, and ignores duplicates.
Signature of the elf_lookup() and elf_obj_lookup() functions changed
to split result/error code and the symbol address returned.
Otherwise, it is impossible to return zero address as the symbol
value, to MD relocation code. This explains the mechanical changes in
elf_machdep.c sources.
The powerpc64 R_PPC_JMP_SLOT handler did not checked error from the
lookup() call, the patch leaves the code as is (untested).
Reported by: glebius
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
When the system has more than a single PCI domain, the bus numbers
are not unique, thus they cannot be used for "pci" device numbering.
Change bus numbers to -1 (i.e. to-be-determined automatically)
wherever the code did not care about domains.
Reviewed by: jhb
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3406
running thread.
It is currently implemented only on amd64 and i386; on these
architectures, it is implemented by raising an NMI on the CPU on which
the target thread is currently running. Unlike stack_save_td(), it may
fail, for example if the thread is running in user mode.
This change also modifies the kern.proc.kstack sysctl to use this function,
so that stacks of running threads are shown in the output of "procstat -kk".
This is handy for debugging threads that are stuck in a busy loop.
Reviewed by: bdrewery, jhb, kib
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D3256
The only operation which is prevented by the hold is the kernel stack
swapout for the faulted thread, which should be fine to allow.
Remove useless checks for NULL curproc or curproc->p_vmspace from the
trap_pfault() wrappers on x86 and powerpc.
Reviewed by: alc (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
pins, they specify the bank and the pin in two separated cells.
This allow the use of vendor's DTS definitions by adding a gpio map
routine that copes with that.
kernel configuration to A20.
There are other boards (namely the banana pi) that use exactly the same
devices.
Additionally, we are moving from static FDT support (DTB compiled
in-kernel) to DTB passed to kernel by the boot loader (ubldr). The u-boot
for these boards are already available on ports and as the crochet support
for these boards isn't committed yet, this should not bring any issues.
Discussed with: ian
If ARMv7 boots in HYP mode, switch to SVC32.
Reviewed by: ian
Submitted by: Wojciech Macek <wma@semihalf.com>
Jakub Palider <jpa@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Differential Revision: https://reviews.freebsd.org/D1810
Add a check to preload_search_info to make sure mod is set. Most of the
callers of preload_search_info don't check that the mod parameter is
set, which can cause page faults. While at it, remove some now unnecessary
checks before calling preload_search_info.
Sponsored by: Citrix Systems R&D
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D3440
operations always had to be aligned and sized to cache lines. On armv6
and later, cache maintenance operates on a cache line if any part of
the line is referenced in the operation, so we don't need extra code to
align the edges of the sync range.
Also, follow the rules from watchdog(9) about what values to return in
various situations (especially, don't touch *error when asked to set a
non-zero timeout that isn't achievable on the hardware).
Also, move the READ/WRITE bus space access macros from the header into the
source file, and rename them to RD2/WR2 to make it clear they're 16-bit
accessors. (READ/WRITE just don't seem like good names to be in a public
header file.)
ARM_ARCH >= 7, use the dmb() macro defined in machine/atomic.h
Submitted by: Steve Kiernan <stevek@juniper.net>
Reviewed by: imp@
Differential Revision: https://reviews.freebsd.org/D3355
redoing it as a separate driver. Now that each hardware timer is handled by
a separate instance of the timer driver, it no longer makes sense to bundle
the pps driver with the regular timecounter code. (When all 8 timers were
handled by one driver there was no choice about this.)
Split the hardware register definitions out to their own file, so that the
new pps driver (coming in a separate commit later) can share them.
With the PPS driver gone, the question of which hardware timer to use for
what purpose becomes much easier (some instances can't do the PPS capture).
Now we can just hardcore timer2 for eventtimer and timer3 for timecounter.
This also now only instantiates devices for the 2 hardware timers actually
used to implement eventtimer and timecounter. This is required so that
other drivers can come along and attach to other hardware timers to provide
other functionality. (In addition to PPS, this hardware can also do PWM
stuff, general pulse width and frequency measurements, etc. Maybe some
day we'll have drivers for those things.)
given the hardware name.
The ti,hwmods property is used (among other things) to associate an fdt node
with a specific instance of some hardware. For example given a device node
that contains the property ti,hwmods = "timer3", if you call this passing
"timer" as the hwmod string to look for it would return 3.
initial thread stack is not adjusted by the tunable, the stack is
allocated too early to get access to the kernel environment. See
TD0_KSTACK_PAGES for the thread0 stack sizing on i386.
The tunable was tested on x86 only. From the visual inspection, it
seems that it might work on arm and powerpc. The arm
USPACE_SVC_STACK_TOP and powerpc USPACE macros seems to be already
incorrect for the threads with non-default kstack size. I only
changed the macros to use variable instead of constant, since I cannot
test.
On arm64, mips and sparc64, some static data structures are sized by
KSTACK_PAGES, so the tunable is disabled.
Sponsored by: The FreeBSD Foundation
MFC after: 2 week
vm_offset_t pmap_quick_enter_page(vm_page_t m)
void pmap_quick_remove_page(vm_offset_t kva)
These will create and destroy a temporary, CPU-local KVA mapping of a specified page.
Guarantees:
--Will not sleep and will not fail.
--Safe to call under a non-sleepable lock or from an ithread
Restrictions:
--Not guaranteed to be safe to call from an interrupt filter or under a spin mutex on all platforms
--Current implementation does not guarantee more than one page of mapping space across all platforms. MI code should not make nested calls to pmap_quick_enter_page.
--MI code should not perform locking while holding onto a mapping created by pmap_quick_enter_page
The idea is to use this in busdma, for bounce buffer copies as well as virtually-indexed cache maintenance on mips and arm.
NOTE: the non-i386, non-amd64 implementations of these functions still need review and testing.
Reviewed by: kib
Approved by: kib (mentor)
Differential Revision: http://reviews.freebsd.org/D3013
This config is already building all modules, so we don't need the
MODULES_EXTRA definition. It was also causing problems to users who
rely on MODULES_OVERRIDE to do the right thing.
Discussed with: ian
Some of FDT blobs for AM335x-based devices use pinmux pullup/pulldown
flag to setup initial GPIO ouputp value, e.g. 4DCAPE-43 sets LCD DATAEN
signal this way. It works for Linux because Linux driver does not enforce
pin direction until after it's requested by consumer. So input with pullup
flag set acts as output with GPIO_HIGH value
Reviewed by: loos
This is a clean-up patch from a serie delivering support for
Annapurna Labs Alpine PoC.
The HAL files have already been added to sys/contrib/alpine-hal
so there is no need for them in the platform directory.
This patch removes obsolete files.
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Differential Revision: https://reviews.freebsd.org/D3248
in lockstat.ko. This means that lockstat probes now have typed arguments and
will utilize SDT probe hot-patching support when it arrives.
Reviewed by: gnn
Differential Revision: https://reviews.freebsd.org/D2993
If KSTACK_PAGES was changed to anything alse than the default,
the value from param.h was taken instead in some places and
the value from KENRCONF in some others. This resulted in
inconsistency which caused corruption in SMP envorinment.
Ensure all places where KSTACK_PAGES are used the opt_kstack_pages.h
is included.
The file opt_kstack_pages.h could not be included in param.h
because was breaking the toolchain compilation.
Reviewed by: kib
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3094
o Return the real hardware state in gpio_pin_getflags() instead of keep
the last state in an internal table. Now the driver returns the real
state of pins (input/output and pull-up/pull-down) at all times.
o Use a spin mutex. This is required by interrupts and the 1-wire code.
o Use better variable names and place parentheses around them in MACROS.
o Do not lock the driver when returning static data.
Tested with gpioled(4) and DS1820 (1-wire) sensors on banana pi.
provide a semantic defined by the C11 fences with corresponding
memory_order.
atomic_thread_fence_acq() gives r | r, w, where r and w are read and
write accesses, and | denotes the fence itself.
atomic_thread_fence_rel() is r, w | w.
atomic_thread_fence_acq_rel() is the combination of the acquire and
release in single operation. Note that reads after the acq+rel fence
could be made visible before writes preceeding the fence.
atomic_thread_fence_seq_cst() orders all accesses before/after the
fence, and the fence itself is globally ordered against other
sequentially consistent atomic operations.
Reviewed by: alc
Discussed with: bde
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
change to GMAC easier on A20 SoCs.
On A10 only the EMAC controller is available (fast ethernet), but on A20
there is also GMAC a high (or better) performant controller (gigabit
ethernet).
On A20 the both controllers uses the same pins to talk to the ethernet PHY
(MII or RGMII) and they can be selected by the GPIO pin mux.
There is work in progress to bring in GMAC support.
The Allwinner SoC has an AHCI device on its internal main bus rather
than the PCI bus. This SoC is somewhat underdocumented, and its SATA
controller is no exception. The methods to support this chip were
harvested from the Linux Allwinner SDK, and then constants invented to
describe what's going on based on low-level constants contained in the
SATA standard and guess work.
This SoC requires a specific AHCI channel setup in order to start the
operations on the channel properly.
Clock setup and AHCI channel setup idea came from NetBSD.
Tested on Cubieboard 2 and Banana pi (and attachment on Cubieboard by
Pratik Singhal).
Differential Revision: https://reviews.freebsd.org/D737
Submitted by: imp
Reviewed by: imp, ganbold, mav, andrew
DMA handles all data transfers up to 128K or 16 segments and fallback to
pio mode when DMA requirements are not met.
The read performance has improved greatly while the write performance also
showed some improvement but seems limited by the card type and quality.
Submitted by: Pratik Singhal <pratiksinghal@freebsd.org>
Sponsored by: Google Summer of Code 2015
Tested on: A10 (cubieboard) and A20 (cubieboard 2 and banana pi)
- Add driver for TDA19988 HDMI framer
- Add simple interface to communicate with HDMI sink: read EDID and set videomode
- Add event-based API to notify LCD controller when HDMI sink is available
- Add HDMI framer node and add refernce to it to lcdc node. This part of
DTS tree is custom and does not match Linux DTS because Linux uses
combination of pseudo-node in DTS and hardcoded driver information
that does not map to our model.
consumers can configure clock frequency
- Add ti_prcm_clk_set_source_freq wrapper for clk_set_source_freq
- Add am335x_clk_set_arm_disp_freq function to control pixel clock
frequency for LCD and HDMI output. Both of them are sensitive
to frequency skews and we need to get pixel clock matching requested
frequency as close to possible
drivers, one for fdt, one for acpi. It then uses this to decide if it will
use fdt or acpi.
The GICv2 (interrupt controller) and Generic Timer drivers have been
updated to handle both cases.
As this is early code we still need FDT to find the kernel console, and
some parts are still missing, including PCI support.
Differential Revision: https://reviews.freebsd.org/D2463
Reviewed by: jhb, jkim, emaste
Obtained from: ABT Systems Ltd
Relnotes: Yes
Sponsored by: The FreeBSD Foundation
This will require for AArch64 as we dont have modules yet.
Sponsored by: HEIF5
Sponsored by: ARM Ltd.
Differential Revision: https://reviews.freebsd.org/D1997
Thread credentials are maintained as follows: each thread has a pointer to
creds and a reference on them. The pointer is compared with proc's creds on
userspace<->kernel boundary and updated if needed.
This patch introduces a counter which can be compared instead, so that more
structures can use this scheme without adding more comparisons on the boundary.
charger configuration and provide some basic control knobs to
set charger voltage and dump config on boot. Two loader tunables
have been added:
o hw.am335x_pmic.bootverbose set to 1 to get more info on the
boot;
o hw.am335x_pmic.vo: set to charger voltage to be applied on
kernel initialization time, supported values are "4.10V",
"4.15V", "4.20V" and "4.25V".
Cleanup code a bit in general, move TPS65217 register
definitions into a separate header, convert bit-banging
defines into bitmap structures.
Also threat the case when power source is neither "AC" nor "USB"
as "Battery", not "Unknown".
On armv6, cache maintenance can trigger page faults. Add handling so that
these turn into SIGSEGV that kills the process rather than panics that kill
the kernel.
Differential Revision: https://reviews.freebsd.org/D2035
Submitted by: Michal Meloun <meloun@miracle.cz>
BREAK_TO_DEBUGGER if they have a serial console (most do). A burst of
serial line noise (such as unplugging a usb serial adapter) can look like
a break and drop a working system into the debugger. The alt break sequence
(<CR>~^B) works fine on both serial and non-serial consoles.
Native ABI do not need signal conversion, only emulators may want this. Usually
emulators implements its own sv_sendsig method. For now only ibcs2 emulator does
not have own sv_sendsig implementation and depends on native sendsig() method.
So, remove any extra attempts to convert signal numbers from native sendsig()
methods except from i386 where ibsc2 is living.
based device.
Following u-boot commands allow FreeBSD boot on
Yiyate Android TV Box (aml8726-m3):
tv open 480p
mmc rescan 0
fatload mmc 0 0x80100000 kernel.bin
go 0x80100000
The current FreeBSD driver doesn't program the video
clocks so the u-boot tv command is necessary in order
for the frame buffer to be useful (otherwise it can
be skipped).
The SD card for the Yiyate Android TV Box doesn't need
anything special beyond creating a FAT16 and a UFS
filesystem.
Differential Revision: https://reviews.freebsd.org/D2636
Submitted by: John Wehle
In smp_rendezvous_cpus we expect to wait for all cpus to enter
smp_rendezvous_action. If we call this holding a proc lock swapper may
attempt to also lock it, however as interrupts are disabled the cpu never
handles the ipi. Because smp_rendezvous_action waits for all signaled
cpus before contining it may get caught waiting for the cpu running swapper
as the proc mutex will be unlocked after smp_rendezvous_cpus finishes.
The fix is to enable interrupts in the configure stage as we should be
doing.
MFC after: 1 week
to sleep while it waits to start scheduling. The boot core can then use
the send-event instruction to wake the cores when they should enter the
scheduler.
MFC after: 1 week
discrimination between different subarch binaries, at least for mips
and arm. Arm is implemented, mips is still tbd, so not currently
exported. aarch64 does not export this because aarch64 binaries use
different tags and flags than arm.
Differential Revision: https://reviews.freebsd.org/D2611
years for head. However, it is continuously misused as the mpsafe argument
for callout_init(9). Deprecate the flag and clean up callout_init() calls
to make them more consistent.
Differential Revision: https://reviews.freebsd.org/D2613
Reviewed by: jhb
MFC after: 2 weeks
