At the moment the manual page is not documenting how to build
a flavored package. Let's start documenting flavors with
an example of a typical use case.
Reported by: cem, dim
Reviewed by: bcr, cem, mat, matthew
Approved by: cem (src)
Differential Revision: https://reviews.freebsd.org/D19531
writes are running. Some of the cases which are not handled properly in driver are:
1. With R1 fastpath supported, single write from CAM layer can consume 2 MPT frames
at driver/firmware level for fastpath qualification(if fw_outstanding < controller Queue Depth).
Due to this driver has to throttle IOs coming from CAM layer as well as second fastpath
write(of R1 write) against Adapter Queue Depth.
If "fw_outstanding" reaches to adapter queue depth, driver should return IOs from CAM layer with
device busy status.While allocating second MPT frame(corresponding to R1 FP write) also, driver
should ensure fw_outstanding should not exceed adapter QD.
2. For R1 fastpath writes completion, driver decrements "fw_oustanding" counter without
really returning MPT frame to free pool. It may cause IOs(with heavy IOs running, consuming whole
adapter Queue Depth) consuming MPT frames reserved for DCMDs(management commands) and
DCMDs(internal and sent by application) not getting MPT frame will start failing.
Below is one test case to hit the issue described above-
1. Run heavy IOs (outstanding IOs should hit adapter Queue Depth).
2. Run management tool (Broadcom's storcli tool) querying adapter in loop (run command- "storcli64 /c0 show" in loop).
3. Management tool's requests would start failing due to non-availability of free MPT frames as all frames would be consumed by IOs.
Fix: Increment/decrement of "fw_outstanding" counter should be in sync with MPT frame get/return.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: Ken
MFC after: 3 days
Sponsored by: Broadcom Inc
This unbreaks ezjail and iocell, which get into an endless loop trying to
figure out how many times "freebsd-update install" needs to be called.
PR: 229346
Submitted by: Mike Cole <mcole36@gmail.com>
Approved by: bapt
MFC after: 1 week
When merging from Netflix's tree, resetting the carsize was dropped
accidentally. This fix fixes that revision by properly resetting how
many are in the car.
Noticed by: mav@
The -l flag sends only the READ CAPACITY (16) sevice action. Normally
we send the READ CAPACITY (10) command, and only send RC16 when the
capacity is larger than 2TB (since that's the max RC10 can
report). However, some badly programmed drives report different
numbers for RC10 and RC16. This can be hard to diagnose, but generally
there's a "Logical block address out of range" error when RC16 reports
a larger number than RC10 and the RC10 number is the correct one. By
comparing the output of readcap with and without the -l argmuent, one
can determine if there's a mismatch and if the DA_Q_NO_RC16 quirk is
needed.
Reviewed by: ken@
Differential Revision: https://reviews.freebsd.org/D19536
These were used to set dst flag and minutes west of UTC
respectively. These are obsolete and have been removed form the
kernel. These existed primarily to faithfully emulate early
Unix ABIs that have been removed from FreeBSD.
Reviewed by: jbh@, brooks@
Differential Revision: https://reviews.freebsd.org/D19550
Research Unix, 7th Edition introduced TIMEZONE and DSTFLAG
compile-time constants in sys/param.h to communicate these values for
the machine. 4.2BSD moved from the compile-time to run-time and
introduced these variables and used for localtime() to return the
right offset from UTC (sometimes referred to as GMT, for this purpose
is the same). 4.4BSD migrated to using the tzdata code/database and
these variables were basically unused.
FreeBSD removed the real need for these with adjkerntz in
1995. However, some RTC clocks continued to use these variables,
though they were largely unused otherwise. Later, phk centeralized
most of the uses in utc_offset, but left it using both tz_minuteswest
and adjkerntz.
POSIX (IEEE Std 1003.1-2017) states in the gettimeofday specification
"If tzp is not a null pointer, the behavior is unspecified" so there's
no standards reason to retain it anymore. In fact, gettimeofday has
been marked as obsolecent, meaning it could be removed from a future
release of the standard. It is the only interface defined in POSIX
that references these two values. All other references come from the
tzdata database via tzset().
These were used to more faithfully implement early unix ABIs which
have been removed from FreeBSD. NetBSD has completely eliminated
these variables years ago. Linux has migrated to tzdata as well,
though these variables technically still exist for compatibility
with unspecified older programs.
So, there's no real reason to have them these days. They are a
historical vestige that's no longer used in any meaningful way.
Reviewed By: jhb@, brooks@
Differential Revision: https://reviews.freebsd.org/D19550
kernel vn_printf() routine when printing out vnodes associated with
a UFS filesystem) to also include the inode's link count, effective
link count, generation number, owner, group, flags, size, and for
UFS2 filesystems, the extent size.
Sponsored by: Netflix
vnode pointer (b_vp). The value of b_vp can be used by "show vnode"
to print the vnode and "show vnodebufs" to print all the clean and
dirty buffers associated with the vnode (which should include this
buffer).
Sponsored by: Netflix
The 16GB, 32GB and 128GB versions of this product all have the same
problem. For some reason, the RC10 size is correct, while the RC16
size is larger (oddly by the capacity size / 1024 bytes). Using the
RC16 size results in illegal LBA range errors when geom tastes the
device. So, expand the quirk to cover all versions of this chip.
Ideally, we'd get both READ CAPACITY 10 and READ CAPACITY 16 sizes and
print a warnnig if they differ and use the smaller of the two numbers,
though that may be problematical as well. Furthermore, SBC-4
encourages users transition to RC16 only, which suggests that in the
future RC10 may disappear from some drives. It's unclear how to cope
with these drives generically.
PR: 234503
MFC After: 1 week
[RegAlloc] Avoid compile time regression with multiple copy hints.
As a fix for https://bugs.llvm.org/show_bug.cgi?id=40986 ("excessive
compile time building opencollada"), this patch makes sure that no
phys reg is hinted more than once from getRegAllocationHints().
This handles the case were many virtual registers are assigned to the
same physreg. The previous compile time fix (r343686) in
weightCalcHelper() only made sure that physical/virtual registers are
passed no more than once to addRegAllocationHint().
Review: Dimitry Andric, Quentin Colombet
https://reviews.llvm.org/D59201
This should fix a hang when compiling certain generated .cpp files in
the graphics/opencollada port.
PR: 236313
MFC after: 1 month
X-MFC-With: r344779
release_80 branch point. Afterwards, we will merge the rest of the
changes in the actual release_80 branch.
PR: 236062
MFC after: 1 month
X-MFC-With: r344779
I tried to save some CPU time on hopeless aggregation attempts, but it seems
the condition I added is overly strict, blocking also aggregation of optional
I/Os in cases which previously were possible. Revert just to be safe.
MFC after: 1 month
Make sure the enter and leave polling routines can be called multiple times
with same setting. Ignore setting polling or event mode twice. This fixes a
deadlock during shutdown if polling mode was already selected.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The ESGL bit was left uninitialized when executing the REPORT LUNS
ioctl. This could allow a zeroed data buffer to be treated as a
scatter/gather list. The firmware would eventually walk past the end
of the data buffer, potentially find what looked like a valid
address/length pair, and write the result to semi-random memory.
Obtained from: Dell EMC Isilon
MFC after: 1 week
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D19398
The Command Reference Number (CRN) is part of the FC-Tape features
that we enable when talking to tape drives. It starts at 1, and
goes to 255 and wraps around to 1. There are a number of reset
type conditions that result in the CRN getting reset to 1. These
are detailed in section 4.10 (table 8) of the FCP-4r02b specification.
One of the conditions is when a PRLI (Process Login) is sent by
the initiator, and the Establish Image Pair bit is set in Word 0
of the PRLI.
Previously, the isp(4) driver core sent a notification via
isp_async() that the target had changed or stayed in place, but
there was no indication of whether a PRLI was sent and whether the
Establish Image Pair bit was set.
The result of this was that in some situations, notably
switching back and forth between a direct connection and a switch
connection to a tape drive, the isp(4) driver would fail to reset
the CRN in situations that require it according to the spec. When
the CRN isn't reset in a situation that requires it, the tape drive
then rejects every subsequent command that is sent to the drive.
It is assuming that the commands are being sent out of order.
So, modify the isp(4) driver to include Word 0 of the PRLI command
when it sends isp_async() notifications of target changes. Look at
the Establish Image Pair bit, and reset the CRN if that bit is set.
With this change, I am able to switch a tape drive back and forth
between a direct connection and a switch connection, and the isp(4)
driver resets the CRN when it should.
sys/dev/isp_stds.h:
Add bit definitions for PRLI Word 0.
sys/dev/ispmbox.h:
Add PRLI Word 0 to the port database type, isp_pdb_t.
sys/dev/ispvar.h
Add PRLI Word 0 to fcportdb_t.
sys/dev/isp.c:
Populate the new prli_word0 parameter in the port database.
In isp_pdb_add_update(), add a check to see if the
Establish Image Pair bit is set in PRLI Word 0. If it is,
then that is an additional reason to create a change
notification.
sys/dev/isp_freebsd.c:
In isp_async(), if the device changed or stayed, look at
PRLI Word 0 to see if the Establish Image Pair bit is set.
If it is, reset the CRN if we haven't already.
MFC after: 1 week
Sponsored by: Spectra Logic
Differential Revision: https://reviews.freebsd.org/D19472
When piping to awk, it's almost always an anti-pattern to use 'grep'
first.
When not in a pipeline, sometimes it is faster to use tail, as awk
must process all the lines in the input stream, and won't 'seek'.
In a pipeline, both grep and awk must process all lines, so we might
as well skip the extra process creation for tail and just use awk
for all the processing.
Reviewed by: jilles
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D19441
It will be used by upcoming NAT64 changes. We use separate code
to avoid propogating EACCES error code to user level applications
when NAT64 consumes a packet.
Obtained from: Yandex LLC
MFC after: 1 week
Sponsored by: Yandex LLC
It is possible, that a processed packet was originated by local host,
in this case m->m_pkthdr.rcvif is NULL. Check and set it to V_loif to
avoid NULL pointer dereference in IP input code, since it is expected
that packet has valid receiving interface when netisr processes it.
Obtained from: Yandex LLC
MFC after: 1 week
Sponsored by: Yandex LLC
Intel 3168 uses another EEPROM section to store channel flags;
port missing bits from iwlwifi to make it work.
PR: 230750, 236235
Tested by: Bert JW Regeer <xistence@0x58.com>
MFC after: 3 days
Also, pass control frames to the host while in MONITOR mode and / or
when promiscuous mode is enabled.
Tested with Netgear WG111 v3 (RTL8187B), STA / MONITOR modes.
MFC after: 2 weeks
- Alignment issues:
* Add missing __packed attributes + padding across all drivers; in
most places there was an assumption that padding will be always
minimally suitable; in few places - e.g., in urtw(4) / rtwn(4) -
padding was just missing.
* Add __aligned(8) attribute for all Rx radiotap headers since they can
contain 64-bit TSF timestamp; it cannot appear in Tx radiotap headers, so
just drop the attribute here. Refresh ieee80211_radiotap(9) man page
accordingly.
- Since net80211 automatically updates channel frequency / flags in
ieee80211_radiotap_chan_change() drop duplicate setup for these fields
in drivers.
Tested with Netgear WG111 v3 (urtw(4)), STA mode.
MFC after: 2 weeks
like this:
pqisrc_build_sgl() at pqisrc_build_sgl+0x8d/frame 0xfffffe009e8b7a00
pqisrc_build_raid_io() at pqisrc_build_raid_io+0x231/frame 0xfffffe009e8b7a40
pqisrc_build_send_io() at pqisrc_build_send_io+0x375/frame 0xfffffe009e8b7b00
pqi_request_map_helper() at pqi_request_map_helper+0x282/frame 0xfffffe009e8b7ba0
bus_dmamap_load_ccb() at bus_dmamap_load_ccb+0xd7/frame 0xfffffe009e8b7c00
pqi_map_request() at pqi_map_request+0x9b/frame 0xfffffe009e8b7c70
pqisrc_io_start() at pqisrc_io_start+0x55c/frame 0xfffffe009e8b7d50
smartpqi_cam_action() at smartpqi_cam_action+0xb8/frame 0xfffffe009e8b7de0
xpt_run_devq() at xpt_run_devq+0x30a/frame 0xfffffe009e8b7e40
xpt_action_default() at xpt_action_default+0x94b/frame 0xfffffe009e8b7e90
dastart() at dastart+0x33b/frame 0xfffffe009e8b7ee0
xpt_run_allocq() at xpt_run_allocq+0x1a2/frame 0xfffffe009e8b7f30
dastrategy() at dastrategy+0x71/frame 0xfffffe009e8b7f60
g_disk_start() at g_disk_start+0x351/frame 0xfffffe009e8b7fc0
g_io_request() at g_io_request+0x3cf/frame 0xfffffe009e8b8010
g_part_start() at g_part_start+0x120/frame 0xfffffe009e8b8090
g_io_request() at g_io_request+0x3cf/frame 0xfffffe009e8b80e0
zio_vdev_io_start() at zio_vdev_io_start+0x4b2/frame 0xfffffe009e8b8140
zio_execute() at zio_execute+0x17c/frame 0xfffffe009e8b8180
zio_nowait() at zio_nowait+0xc4/frame 0xfffffe009e8b81b0
vdev_queue_io_done() at vdev_queue_io_done+0x138/frame 0xfffffe009e8b81f0
zio_vdev_io_done() at zio_vdev_io_done+0x151/frame 0xfffffe009e8b8220
zio_execute() at zio_execute+0x17c/frame 0xfffffe009e8b8260
taskqueue_run_locked() at taskqueue_run_locked+0x10c/frame 0xfffffe009e8b82c0
taskqueue_thread_loop() at taskqueue_thread_loop+0x88/frame 0xfffffe009e8b82f0
fork_exit() at fork_exit+0x84/frame 0xfffffe009e8b8330
fork_trampoline() at fork_trampoline+0xe/frame 0xfffffe009e8b8330
Reviewed by: deepak.ukey_microsemi.com, sbruno
MFC after: 2 weeks
Sponsored by: Klara Inc.
Differential Revision: https://reviews.freebsd.org/D19470
FreeBSD base system does not provide an ACPI handler for the PC/AT RTC/CMOS
device with PnP ID PNP0B00; on some HP laptops, the absence of this handler
causes suspend/resume and poweroff(8) to hang or fail [1], [2]. On these
laptops EC _REG method queries the RTC date/time registers via ACPI
before suspending/powering off. The handler should be registered before
acpi_ec driver is loaded.
This change adds handler to access CMOS RTC operation region described in
section 9.15 of ACPI-6.2 specification [3]. It is installed only for ACPI
version of atrtc(4) so it should not affect old ACPI-less i386 systems.
It is possible to disable the handler with loader tunable:
debug.acpi.disabled=atrtc
Informational debugging printf can be enabled by setting hw.acpi.verbose=1
in loader.conf
[1] https://wiki.freebsd.org/Laptops/HP_Envy_6Z-1100
[2] https://wiki.freebsd.org/Laptops/HP_Notebook_15-af104ur
[3] https://uefi.org/sites/default/files/resources/ACPI_6_2.pdf
PR: 207419, 213039
Submitted by: Anthony Jenkins <Scoobi_doo@yahoo.com>
Reviewed by: ian
Discussed on: acpi@, 2013-2015, several threads
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D19314
trying to use disk_add_alias() to make spi* an alias for mx25l*. It turns
out disk_add_alias() works for partitions, but not slices, and that's hard
to fix.
This change is, in effect, a partial revert of r344526.
The mips world relies on the existence of flashmap names formatted as
/dev/flash/spi0s.name, whereas pretty much nothing relies on at45d devices
using the /dev/spi* names (because until recently the at45d driver didn't
even work reliably). So this change makes mx25l devices the sole owner of
the /dev/flash/spi* namespace, which actually makes some sense because it is
a SpiFlash(tm) device, so flash/spi isn't a horrible name.
Reported by: Mori Hiroki <yamori813@yahoo.co.jp>
PFIL_MEMPTR flag are intentionally providing a memory address that
isn't aligned to pointer alignment. This is done to align an IPv4
or IPv6 header that is expected to follow Ethernet header.
When we return PFIL_REALLOCED we store a pointer to allocated mbuf
at this address. With this change the KPI changes to store the pointer
at aligned address, which usually yields in +2 bytes.
Provide two inlines:
pfil_packet_align() to get aligned pfil_packet_t for a misaligned one
pfil_mem2mbuf() to read out mbuf pointer from misaligned pfil_packet_t
Provide function pfil_realloc(), not used yet, that would convert a
memory pfil_packet_t to an mbuf one.
Reported by: hps
Reviewed by: hps, gallatin
When updating across this change (the introduction of ino64), the
"fast and loose" practice of rebooting to multiuser and then doing an
installworld fails with missing symbols. Recommend strongly that users
do this in single user mode. The multiuser case only ever works by
accident because its requirements are stronger than is supported
accross this change. It usually works because critical symbols don't
change their version number in libc, which wasn't the case here.
When reading UPDATING from single user in vi, I noticed a few wrapped,
so fix them to not wrap.
expand -8 UPDATING | awk 'length > 80'
made this easy to find all the offenders.
Add note about needing to start zfs because mount -a doesn't do that.
Add the word 'supported' before 'older branches' for older binaries.
Add note about options in custom config files as well.
Registers visible from 'show reg' don't always match the registers from the
offending trap frame. Knowing the frame address lets one examine the
registers manually.
MFC after: 1 week
