the main processing queue, clear the NAK counter for any associated
BULK or CONTROL transfers and poll the endpoint(s) for 1 millisecond
at 125us rate interval, before going into slow, 10ms, NAK polling mode
again. This has the effect that typical ping-ping protocols respond
quicker when initiated from the USB host.
MFC after: 2 weeks
- For non-periodic traffic we only need to wait two SOFs before
disabling the channel.
- Make sure we release the TX FIFO tracking level after the host
channel is disabled.
- Make sure the host channel state gets reset/disabled initially.
- Two minor code style changes.
MFC after: 2 weeks
- Rework how we allocate and free USB host channels, so that we only
allocate a channel if there is a real packet going out on the USB
cable.
- Use BULK type for control data and status, due to instabilities in
the HW it appears.
- Split FIFO TX levels into one for the periodic FIFO and one for the
non-periodic FIFO.
- Use correct HFNUM mask when scheduling host transactions. The HFNUM
register does not count the full 16-bit range.
- Correct START/COMPLETION slot for TT transactions. For INTERRUPT and
ISOCHRONOUS type transactions the hardware always respects the ODDFRM
bit, which means we need to allocate multiple host channels when
processing such endpoints, to not miss any so-called complete split
opportunities.
- When doing ISOCHRONOUS OUT transfers through a TT send all data
payload in a single ALL-burst. This deacreases the likelyhood for
isochronous data underruns.
- Fixed unbalanced unlock in case of "dwc_otg_init_fifo()" failure.
- Increase interrupt priority.
MFC after: 2 weeks
controller driver by piggybacking the SOF interrupt when issuing new
and checking old transfers. Number of interrupts was reduced by 30%
when doing Isochronous transfers.
Use correct GINTMSK_XXX macros when accessing the DWC OTG interrupt
mask register.
Add code to adjust the frame interval register which influences the
SOF rate.
MFC after: 2 weeks
speed data traffic going directly to a USB device or through a
so-called USB transaction translator.
Add checks that we are not overusing the TX FIFO.
MFC after: 2 weeks
define a few imx_ccm_foo() functions that are implemented by the imx51 or
imx6 ccm code. Of course, the imx6 ccm code is still more a wish than
reality, so for now its implementations just return hard-coded numbers.
a jtag debugging product, which was used on early Beaglebone boards (later
boards used a standard FTDI 2232C product ID). Change the name accordingly,
and also add an entry for XDS100V3, the latest version of that product
which has its own new product ID number.
Device type and revision is now determined from the bcdDevice field and
doesn't need to be in the table at all. The feature that skips creation
of /dev/ttyU* entries for jtag and gpio interfaces is enhanced:
- The feature is now optional, but enabled by default. A tunable and
sysctl are available to control it: hw.usb.uftdi.skip_jtag_interfaces.
- We no longer assume interface #0 is the only jtag interface. Up to
eight interfaces per chip can be flagged as jtag. (Current ftdi chips
support a max of 4 interfaces; this leaves room for growth.)
- Some manufacturers don't change the product ID or use the same ID for
different devices intended for both serial-comms and jtag/gpio use.
Often while the product ID is the same, the product name string is
different, so it's now possible to search for the product name in a
table of strings and get the set of non-tty interfaces from that table.
- Add a comment about FTDI and ZLPs.
- Correctly check odditiy of baud rate divisor.
- Correct IOCTL handling for "error" and "event" char.
MFC after: 1 weeks
other modes supported by the FTDI serial adapter chips.
In addition to adding the new ioctls, this change removes all the code
that reset the chip at attach and open/close time, and also the code
that turned on RTS/CTS flow control on open without any permission to do
so (that was just always a bug in the driver).
When FTDI chips are configured as GPIO or MPSSE or other special-purpose
uses by an attached serial eeprom, the chip will power on with certain
pins driven or floating, and it's important that the driver not do
anything to the chip to perturb that unless it receives a specific
command to do so. When used for "plain old serial comms" the chip
powers on into the right mode and never needs to be reset while it's
running to operate properly, so this change is transparent to most users.
While I'm here, remove aue_eeprom_getword() as its only usage is to
read station address and make it more readable. This change is
inspired by NetBSD.
With this change, aue(4) should work on big endian architectures.
PR: 188177
default wMaxPacketSize (64 or 512 bytes). This actually helps older FTDI
devices (which were USB 1/full speed) more than the new H-series high
speed, but even for the new chips it helps cut the number of interrupts
when doing very high speed (3-12mbaud).
Recent FDTI chips have the ability to operate at up to 12mbps. The newer
chips with faster clocks have the same usb vendor/product IDs as the older
chips; the bcdDevice field must be used to detect the newer versions. This
change includes a new function to do that instead of using just the IDs from
the vendor/product table.
The code to choose the baud clock divisor is completely rewritten. In
addition to supporting the new higher clock rates, the rewrite fixes a
longstanding bug in the old code which put the high bits of the fractional
part of the divisor into the wrong place in the wIndex field. That bug
was mostly harmless -- it accidentally didn't affect standard baud rates
and would only show up when using relatively fast non-standard rates.
create character devices. The deadlock can happen if an application is
issuing IOCTLs which require USB refcounting, at the same time the USB
device is detaching.
There is already a counter in place in the USB device structure to
detect this situation, but it was not always checked ahead of invoking
functions that might destroy character devices, like detach, set
configuration, set alternate interface or detach active kernel driver.
Reported by: Daniel O'Connor <doconnor@gsoft.com.au>
MFC after: 1 week
The NetBSD Foundation states "Third parties are encouraged to change the
license on any files which have a 4-clause license contributed to the
NetBSD Foundation to a 2-clause license."
This change removes clauses 3 and 4 from copyright / license blocks that
list The NetBSD Foundation as the only copyright holder.
Sponsored by: The FreeBSD Foundation
1) Add support for page back/forward.
2) While doing HOR scrolling, disable VER scrolling.
3) Checking dx_sum and dy_sum before emulate right button, this can
avoids unexpected right button press.
4) Fix stable pointer operation when emulating middle button.
Submitted by: Huang Wen Hui <huanghwh@gmail.com>
MFC after: 2 weeks
- Support for double-tap and drag.
- Support for 2-finger horizontal scrolling which translates to page-back/forward events.
- Single finger tap is equivalent to a left-button press.
- Two-finger taps are mapped to the right-button click.
- Three fingers are mapped to middle button.
- Add sysctl to disable single finger tapping.
- Fix for multiple open of /dev/atp0
- Enhanced support for the Fountain/Geyser family by adding Geyser4.
- Update manual page.
Submitted by: Rohit Grover <rgrover1@gmail.com>
MFC after: 2 weeks
Before this patch, curvnet was NULL.
When the VIMAGE kernel option is enabled, this eliminates
kernel panics when USB ethernet devices are plugged in.
PR: 183835
Submitted by: Hiroo Oono <hiroo.ono at gmail dot com>
about uss820dci_odevd being unused, by adding it to the part that
handles getting descriptors.
Reported by: loos
Reviewed by: hselasky
MFC after: 3 days
- Get USB input report length from HID descriptor.
- Use 1 finger TAP for devices which has no integrated button.
- Move data buffer to softc instead of allocating it.
MFC after: 1 week
should fix DMA descriptor caching issues seen with the EHCI controller
found in Google Chromebook C720 during removal and insertion of USB
devices.
MFC after: 1 week
Reported by: Matthew Dillon at DragonFlyBSD
Useful for so-called USB tethering.
- Imported code from OpenBSD
- Adapted code to FreeBSD
- Removed some unused functions
- Fixed some buffer encoding and decoding issues
- Optimised data transport path a bit, by sending multiple packets at a time
- Increased receive buffer to 16K
Obtained from: OpenBSD
Requested by: eadler @
MFC after: 2 weeks
to check the status property in their probe routines.
Simplebus used to only instantiate its children whose status="okay"
but that was improper behavior, fixed in r261352. Now that it doesn't
check anymore and probes all its children; the children all have to
do the check because really only the children know how to properly
interpret their status property strings.
Right now all existing drivers only understand "okay" versus something-
that's-not-okay, so they all use the new ofw_bus_status_okay() helper.
- Use system provided functions for HID report requests.
- Nice the mode setting, because the USB hardware does appear to
handle the commands right away.
MFC after: 1 week
that all pressed keys are released before completing the USB keyboard
detach. This will prevent so-called "ghost-keys" from appearing after
that the USB device generating the key event(s) has been detached.
MFC after: 1 week
a timeout value of a single tick is given. With FreeBSD-10 and newer
the current system time is used as a starting point, and the minimum
callout time of a single tick will be guaranteed. This patch mostly
affect the DMA delay timeouts, which are typically in the range from
0.125 to 2ms.
MFC after: 1 week
with USB device detach when using character device handles. This also
includes LibUSB. It turns out that "usb_close()" cannot always get a
reference to clean up its USB transfers and such, if called during the
kernel USB device detach.
Analysis by: hselasky @
Reported by: Juergen Lock <nox@jelal.kn-bremen.de>
MFC after: 1 week
non-modifier key press. This prevents so-called "ghost
keyboards" keeping modifier keys pressed while not
actually seen as a real keyboard.
MFC after: 2 weeks
found in High Speed USB HUBs which translate from High Speed USB into
FULL or LOW speed USB. In some rare cases SPLIT transactions might get
lost, which might leave the TT in an unknown state. Whenever we detect
such an error try to issue either a clear TT buffer request, or if
that is not possible reset the whole TT.
MFC after: 1 week
controller found in the MBP2013 has been observed to not work properly
unless this operation is performed.
MFC after: 1 week
Tested by: Huang Wen Hui <huanghwh@gmail.com>
The origin of WEP comes from IEEE Std 802.11-1997 where it defines
whether the frame body of MAC frame has been encrypted using WEP
algorithm or not.
IEEE Std. 802.11-2007 changes WEP to Protected Frame, indicates
whether the frame is protected by a cryptographic encapsulation
algorithm.
Reviewed by: adrian, rpaulo
value. The "Intel Lynx Point" XHCI controller found in the MBP2013 has
been observed to not always set the event interrupt bit while there
are events to consume in the event ring.
MFC after: 1 week
Tested by: Huang Wen Hui <huanghwh@gmail.com>
Some Intel XHCI controlles timeout processing so-called "TRBs" when
the final LINK TRB of a so-called "TD" has the CHAIN-BIT set.
MFC after: 1 week
Tested by: glebius @
receiving Zero Length Packets, ZLPs. See comment in code for more
information.
MFC after: 1 week
Reported by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
shifts into the sign bit. Instead use (1U << 31) which gets the
expected result.
This fix is not ideal as it assumes a 32 bit int, but does fix the issue
for most cases.
A similar change was made in OpenBSD.
Discussed with: -arch, rdivacky
Reviewed by: cperciva
adapters. Both devices support Gigabit Ethernet and USB 2.0, and the AX88179
supports USB 3.0. The driver was written by kevlo@ and lwhsu@, with a few
bug fixes from me.
MFC after: 2 months
softc's "sc->sc_mtx" mutex. Currently the callout was marked
multi-processor safe, which is fine, but it is better to
start/stop/reset callouts while holding the "run" drivers own
mutex. While at it add a missing "ULL" at end of the 64-bit unsigned
integer constant.
MFC after: 1 week
CDC=0 simply means "no command codes", CDC=1 means "AT command codes."
There's no driver change required! It's purely to tell the application
layer whether to speak AT commands or not. Things are all still serial.
PR: usb/183505
Reviewed by: hps
MFC after: 1 week
is not idential to "uint32_t" when defining set channel prototype
functions. The WLAN channel range should be from 0 to 65535
inclusivly, and u_int should be fine for this purpose.
than one unit with four busses attached to it. This allows us to use
existing fdt data which describes separate devices with separate resources.
It also allows any combination of the units to be en/disabled in the
board dts files.
Adjust our dts code to match what's used by linux and u-boot now that
we're structured to do so.
Document lots of interesting stuff learned whiling doing this with a big
comment block in the driver, so I don't have to re-learn it for the next
round of changes.
mostly by adjustments to debugging printf() format specifiers. For high
numbered LUNs, also switch to printing them in hex as per SAM-5.
MFC after: 2 weeks
interface. Make MII drivers forget about 'struct ifnet'.
Later plan is to provide an administrative downcall from ifnet
layer into drivers, to inform them about administrative status
change. If someone thinks that processing MII events for an
administratively down interface is a big problem, then drivers
would turn MII processing off.
The following MII drivers do evil things, like strcmp() on
driver name, so they still need knowledge of ifnet and thus
include if_var.h. They all need to be fixed:
sys/dev/mii/brgphy.c
sys/dev/mii/e1000phy.c
sys/dev/mii/ip1000phy.c
sys/dev/mii/jmphy.c
sys/dev/mii/nsphy.c
sys/dev/mii/rgephy.c
sys/dev/mii/truephy.c
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
and not 8-bit. Fix support for isochronous transfers in USB host mode.
Fix a whitespace while at it.
MFC after: 1 week
Reported by: SAITOU Toshihide <toshi@ruby.ocn.ne.jp>
PR: usb/181987
routing if we get certain errors. Poll for command completion upon
command timeouts. The XHCI error events might not generate interrupts.
MFC after: 1 week
Reported by: Daniel Gerzo <danger@rulez.sk>, Antonis Anastasiadis <anastasiadis@datalive.gr>
PR: usb/181159
Approved by: re (gjb)
extremely outdated, and I doubt that it was ever used for ifnet drivers.
It was used for AF_INET sockets in pre-FreeBSD time.
Approved by: re (hrs)
Sponsored by: Nginx, Inc.
IMAN register to clear the pending interrupt status bits. This patch
tries to solve problems seen on the MacBook Air, as reported by
Johannes Lundberg <johannes@brilliantservice.co.jp>
MFC after: 1 week
Linux targets without breaking the existing IOCTL API.
- Remove some not-needed header file inclusions.
- Wrap a long line.
MFC after: 1 week
Reported by: Damjan Jovanovic <damjan.jov@gmail.com>
Support chipsets are the Realtek RTL8188SU, RTL8191SU, and RTL8192SU.
Many thanks to Idwer Vollering for porting/writing the man page and for
testing.
Reviewed by: adrian, hselasky
Obtained from: OpenBSD
Tested by: kevlo, Idwer Vollering <vidwer at gmail.com>
and protocol 1 are USB ethernet adapters. This avoids keeping and updating
the product list every now and then. This patch will add support for the
USB ethernet interface found in the IPAD.
MFC after: 1 week
Kernel include files (i.e. sys/*.h) come first; normally, include
<sys/types.h> OR <sys/param.h>, but not both. <sys/types.h> includes
<sys/cdefs.h>, and it is okay to depend on that.
USB mouse and USB modem classes. Hopefully someone will find
these examples useful when implementing USB device side drivers
using the FreeBSD USB stack.
The Block Event Interrupts, BEI, feature does not
work like expected with the Renesas XHCI chipsets.
Revert feature.
While at it correct the TD SIZE computation in
case of Zero Length Packet, ZLP, in the end of a
multi frame USB transfer.
MFC after: 1 week
PR: usb/180726
We need to fix wpa_supplicant because it checks whether the card has
ic_cryptocaps set. Since net80211 can do software encryption this check in
wpa_supplicant is wrong.
"Gamers Keyboards" by adding a tunable, "hw.usb.ukbd.pollrate", which
can fix the polling rate of the attached USB keyboards in the range
1..1000Hz. A similar feature already exists in the USB mouse
driver. Use with care! Might leave you without keyboard input. This
feature is only available when the USB_DEBUG option is set in the
kernel configuration file.
Correct "unit" type to "int" while at it.
checksum header. The header contains a received frame length but
the defined length for AX88772B is different with other ASIX
controllers. When the RX checksum is off, AX88772B controller does
not prepend a checksum header so driver has to use normal header
length mask.
This change should fix RX errors when RX checksum offloading is
off.
Tested by: kevlo
MFC After: 1 week
generic mii_phy_reset().
- Return the result of mii_mediachg() rather than blindly returning 0.
- on smsc(4), driver lock should be held to get current
mii_media_active/mii_media_status value.
Reviewed by: yongari
Realtek RTL8188CU/RTL8192CU USB IEEE 802.11b/g/n wireless cards.
This driver requires microcode which is available in FreeBSD ports:
net/urtwn-firmware-kmod.
Hiren ported the urtwn(4) man page from OpenBSD and Glen just commited a port
for the firmware.
TODO:
- 802.11n support
- Stability fixes - the driver can sustain lots of traffic but has trouble
coping with simultaneous iperf sessions.
- fix debugging
MFC after: 2 months
Tested by: kevlo, hiren, gjb
1) Only multi-TD isochronous transfers should use NORMAL
type after specific type as per XHCI specification.
2) BEI bit is only available in NORMAL and ISOCHRONOUS
TRB types. Don't use this bit for other types to avoid
hardware asserts. Reserved bits should be don't care
though ...
MFC after: 1 week
PR: usb/179342
the regular interrupt handler is not working properly or
in case of MSI interrupts which are not yet supported.
Remove interrupt setup code for FreeBSD versions older
than 700031.
MFC after: 1 week
PR: usb/179342
controller hardware most likely present on UHCI chipsets aswell. The
bug manifests itself when issuing isochronous transfers and bulk
transfers towards the same device simultaneously. From time to time it
happens that either the completion IRQ was missing or that the
completion IRQ was happening before the ITD/SITD was completely
written back to memory. The workaround assumes that double buffered
isochronous transfers are used, and that a second interrupt is
generated at the beginning of the next isochronous transfer to
complete the previous one. Possibly skipping the interrupt at the last
isochronous frame is possible, but will then break single buffered
isochronous transfers. For now we can live with some extra interrupts.
MFC after: 1 week
o The CP2101 and CP2102 do not support GPIO pin use at all, enforce this.
o Support reading the GPIO status on the second port of the CP2105. More
work is needed before the CP2105 GPIO pins can be used as outputs.
Hardware donated by: Silicon Labs
MFC after: 3 weeks
in reduced memory systems.
- Split allocation and freeing of the configuration descriptor into a separate
function, so that the configuration descriptor can be made fixed size
to save memory allocations. This applies for both device and host mode.
