o multiple modules can be unloaded at once (specified either by id or be
module name)
o exit with EX_USAGE after usage() is called.
o remove unused variables, since we keep command line flags as bitmask,
in 'opt'.
o 'kldload -n ...' does nothing. Add comment to this options.
Additionally:
o Update manual page to conform new functionality.
o Increace WARNS to 6. Because we can.
Approved by: cognet (mentor)
MFC after: 1 week
Staticize two tables thare are not visible in <resolv.h>
and which are also local in Solaris' libresolv.
Remove two functions that are not referenced in libc nor
anywhere else I can find, not visible in <resolv.h> and
which are also local in Solaris libresolv.
in the buffer. This isn't exactly the patch that Stephen submitted, but
is based on one of his suggestions.
PR: 93841
Submitted by: Stephen Montgomery-Smith <stephen@math.missouri.edu>
MFC after: 2 weeks
and want to have crypto support loaded as KLD. By moving zlib to separate
module and adding MODULE_DEPEND directives, it is possible to use such
configuration without complication. Otherwise, since IPSEC is linked with
zlib (just like crypto.ko) you'll get following error:
interface zlib.1 already present in the KLD 'kernel'!
Approved by: cognet (mentor)
Otherwise a kernel build would break in the coda5 module if the main
kernel conf file enabled CODA_COMPAT_5, too. Redefined symbols are
strictly disallowed by -Werror.
To overcome this issue, introduce a different symbol indicating coda5
build, CODA5_MODULE, and translate it to CODA_COMPAT_5 appropriately
in /sys/coda/coda.h.
MFC after: 3 days
o Also, fdisk_pc98 appears to support -i, so add it to the man page.
o Ditto -v
o Change the name from PC partition table maintenance program to NEC PC-98x1
partition table maintenance program, since it is possible to have a DOS MBR
formatted disk on FreeBSD/pc98 now (although we don't install any tools for
this).
so other threads can not see it if we unlock the proc
lock (this can happen in knlist_delete). Don't do wakeup,
it is not necessary.
2. Decrease kaio_buffer_count in biohelper rather than
doing it in aio_bio_done_notify.
3. In aio_bio_done_notify, don't send notification if KAIO_RUNDOWN
was set, because the process is already in single thread mode.
4. Use assignment to initialize aiothreadflags.
5. AIOCBLIST_RUNDOWN is not useful, axe the code using it.
6. use LIO_NOP instead of zero.
not hang the system for 5 seconds. If a TMF doesn't complete within,
oh, say 500ms, that's enough.
Put in a printout to catch mpt_recover_commands being activated with
no commands.
*both* SAS and FC, not just SAS.
b) Don't tell the chip we want it to do FIFO signalling if we actually
don't set up the address where the FIFO signal is supposed to be written
(oops).
o Merge the -I switch from i386 verison to initialize the partition table
to use the maximum amount possible for a single FreeBSD table.
o Improve warning when the geom method fails (which I think it
always will until geom_pc98 is updated to respond to this ctl message)
o when writing out the boot sector, we have to write out a minimum of
1024 bytes or the sector size. This is different than the i386 case where
we need to write out a minimum of 512 bytes (which is also the minimum
sector size). We already handle this difference on reading, but didn't
in writing, so attempting to write a new partition table would fail.
o Add MID to the -s output, since pc98 users are likely interested in
both of these parameters.
# I can now initialize disks on my pc98 machine either by -I or by
# manually entering the parameters. I don't know if fdisk -B works or not,
# since I'm not willing to risk my only working boot disk to test it..
is closed and then reopened. This appears to be necessary now that
we no longer clear endpoint stalls every time a pipe is opened.
Previously we could assume an initial toggle value of zero because
the clear-stall operation resets the device's toggle state.
Reported by: Holger Kipp
MFC after: 3 days
on UFS2 inodes are initialised as they are needed, rather than at
newfs time. When quot encountered these inodes it could produce
crazy results.
Now, on UFS2 filesystems, quot's get_inode function will bzero
unallicated inodes before passing them back to a caller. This is
how UFS2 initialises new inodes, so this should work OK.
Also, while I'm here, make quot exit with an error if it finds
inodes of an unknown type. This should help catch future problems
of this type.
Reviewed by: iedowse
MFC after: 1 week
