Add gpioled(4) to BEAGLEBONE kernel and add the description of the four
on-board leds of beaglebone-black to its DTS file.
Approved by: adrian (mentor, implicit)
in the dts source, and adding the right devices to the kernel config. Also
generally bring the kernel config into line with what we have for other
Marvell/Kirkwood systems (add lots of useful devices and options).
One particularly notable addition amongst the kernel config changes is
USB_HOST_ALIGN=32, which may help eliminate data corruption on USB drives.
PR: kern/181975 arm/162159
the LED specification was just misplaced). The rather odd memory mappings
that were in place used an undocumented attribute value (0x0f) that caused
problems with the system.
Submitted by: Markus Pfeiffer <markus.pfeiffer@morphism.de>
sys/boot/fdt/dts/bindings-gpio.txt. Make the led pin an output, add the
missing flag field. No functional change (gpioled(4) isn’t supported on
FDT systems yet).
Approved by: adrian (mentor)
Use the published compatible strings (our own invention, "ti,mmchs" is
still accepted as well, for now).
Don't blindly turn on 8-bit bus mode, because even though the conroller
supports it, the board has to be wired appropriately as well. Use the
published property (bus-width=<n>) and honor all the valid values (1,4,8).
The eMMC device on a Beaglebone Black is wired for 8-bit, update the dts.
The mmchs controller can inherently do both 1.8v and 3.0v on the first
device and 1.8v only on other devices, unless an external transceiver is
used. Set the voltage automatically for the first device and honor
the published fdt property (ti,dualvolt) for other devices.
Thanks go to Ilya Bakulin for figuring out the voltage compatibility stuff.
The imx6.dtsi is incomplete, but has enough to support devices that work
right now. Eventually it will need to be split into several files that
account for the differences between SoCs in the imx6 family.
The board config for Wandboard Dual is untested. Solo and Quad work, but
one one core is turned on for the quad right now (baby steps).
than one unit with four busses attached to it. This allows us to use
existing fdt data which describes separate devices with separate resources.
It also allows any combination of the units to be en/disabled in the
board dts files.
Adjust our dts code to match what's used by linux and u-boot now that
we're structured to do so.
Document lots of interesting stuff learned whiling doing this with a big
comment block in the driver, so I don't have to re-learn it for the next
round of changes.
All Armada XP chips should be affected. It is necessary to handle
busy interrupt/indication by enabling busy-detect property in DTS.
Tested by: kevlo
Approved by: cognet (mentor)
Switch the majority of device configuration to FDT from hints.
Add BERI_*_BASE configs to reduce duplication in the MDROOT and SDROOT
kernels.
Add NFS and GSSAPI support by default.
MFC after: 3 days
Sponsored by: DARPA/AFRL
The TI uart hardware is ns16550-compatible, except that before it can
be used the clocks and power have to be enabled and a non-standard
mode control register has to be set to put the device in uart mode
(as opposed to irDa or other serial protocols). This adds the extra
code in an extension to the standard ns8250 probe routine, and the
rest of the driver is just the standard ns8250 code.
The MMCHS hardware is pretty much a standard SDHCI v2.0 controller with a
couple quirks, which are now supported by sdhci(4) as of r254507.
This should work for all TI SoCs that use the MMCHS hardware, but it has
only been tested on AM335x right now, so this enables it on those platforms
but leaves the existing ti_mmchs driver in place for other OMAP variants
until they can be tested.
This initial incarnation lacks DMA support (coming soon). Even without it
this improves performance pretty noticibly over the ti_mmchs driver,
primarily because it now does multiblock IO.
Add support for A20 timer.
Correct interrupt offset depending from chip.
Add basic code for CPU configuration module.
For now, add kernel config and dts file
(only FDT blob related problem needs to be solved later in
order to have one kernel for both cubieboard1 and 2).
Approved by: ray@
the beaglebone-specific .dts file.
Add a new .dts for the BeagleBone Black with more memory,
slightly different pinmux initialization, and with mmchs1
configured (though the latter doesn't quite work yet).
to driver specific files.
- window initialization is done during device attach
- CESA TDMA decoding windows values are set based on DTS,
not copied from CPU registers
- remove unnecessary virtual mapping
- update dts file
Obtained from: Semihalf
