and just show old (cached) values. Controller will not respond to
the command unless MAC is enabled so DUMP request for down
interface caused request timeout.
RealTek changed TX descriptor format for later controllers so these
controllers require MSS configuration in different location of TX
descriptor. TSO is enabled by default for controllers that use new
descriptor format.
For old controllers, TSO is still disabled by default due to broken
frames under certain conditions but users can enable it.
Special thanks to Hayes Wang at RealTek.
MFC after: 2 weeks
These controllers consist of two Marvell 88SE9128 6Gbps SATA chips and
PLX PCIe bridge. As result, they seem to be agree to work with ahci(4)
as usual HBAs. The only noticed issue is that RAID BIOS disables all
drive caches during boot, though `camcontrol cmd ...` is able to fix that.
Those who wants RAID functionality can still use closed proprietary driver
from HighPoint site.
MFC after: 1 week
erroneously, assumed that 4 bytes of data were in the first
mbuf of a list by replacing the bcopy() with m_copydata().
Also, replace the uses of m_pullup(), which can fail for
reasons other than not enough data, with m_copydata().
For the cases where it isn't known that there is enough
data in the mbuf list, check first via m_len and m_length().
This is believed to fix a problem reported by dpd at dpdtech.com
and george+freebsd at m5p.com.
Reviewed by: jhb
MFC after: 8 days
accurate. <sys/linker_set.h> is one of the very few headers similar to
<sys/queue.h> for which nested includes is allowed.
PR: docs/153654
Reviewed by: bde
MFC after: 1 month
install or remove non-SCI interrupt handlers per ACPI Component Architecture
User Guide and Programmer Reference. ACPICA may install such interrupt
handler when a GPE block device is found, for example. Add a wrapper for
ACPI_OSD_HANDLER, convert its return values to ours, and make it a filter.
Prefer KASSERT(9) over panic(9) as we have never seen those in reality.
Clean up some style(9) nits and add my copyright.
DMA boundary bug and runs with PCI-X mode. watchdog timeout was
observed on BCM5704 which lives behind certain PCI-X bridge(e.g.
AMD 8131 PCI-X bridge). It's still not clear whether the root
cause came from that PCI-X bridge or not. The watchdog timeout
indicates the issue is in TX path. If the bridge reorders TX
mailbox write accesses it would generate all kinds of problems but
I'm not sure. This should be revisited.
Tested by: Michael L. Squires (mikes <> siralan dot org)
issue seen on PCIX BCM5704 controller. r216970 fixed the issue but
the DMA address space restriction was applied to all bge(4)
controllers such that it caused unnecessary performance degradation
for controllers that have no such issues.
one. Search global objects, together with main object and
dependencies, for the requested symbol.
Move the common code from symlook_default() into new helper
symlook_global(), and use it both in symlook_global() and
get_program_var_addr().
Supply lock state to get_program_var_addr().
Reviewed by: kan
Tested by: Mykola Dzham <i levsha me>
o) Clear/acknowledge receive interrupt at end of thread. This gives the
management interfaces performance on the order of 100Mbps rather than
the previous level of 10Mbps on my MR-730.
hint is 0 when no SACK data is received to update the hint with. This was
accidentally omitted from r216753.
Sponsored by: FreeBSD Foundation
MFC after: 10 weeks
X-MFC with: 216753
o) Add 'octm', a trivial driver for the 10/100 management ports found on some
Octeon systems.
o) Make the Simple Executive's management port helper routines compile on
FreeBSD (namely by not doing math on void pointers.)
o) Add a cvmx_mgmt_port_sendm routine to the Simple Executive to send an mbuf
so there is only one copy in the transmit path, rather than having to first
copy the mbuf to an intermediate buffer and then copy that to the Simple
Executive's transmit ring.
o) Properly work out MII addresses of management ports on the Lanner MR-730.
XXX The MR-730 also needs some patches to the MII read/write routines, but
this is sufficient for now. Media detection will be fixed in the future
when I can spend more time reading the vendor-supplied patches.
quite awful, because e.g. 4 packets will come in and get processed on 4
different cores at the same time, really battling with the TCP stack quite
painfully. For now, just run one task at a time.
This gets performance up in most cases to where it was before the correctness
fixes that got interrupts to run on all cores (except in high-load TCP transmit
cases where all we're handling receive for is ACKs) and in some cases it's
better now. What would be ideal would be to use a more advanced interrupt
mitigation strategy and possibly to use different workqueue groups per port for
multi-port systems, and so on, but this is a fine stopgap.
When running with a custom locale setup, it's easy to confuse the
date regression tests and cause them to fail, e.g. when LANG='C'
but LC_ALL='el_GR.UTF-8'. Set LC_ALL to 'C', which overrides all
other LC_xxx options, to avoid this sort of problem.
Reviewed by: uqs, edwin
__assert() is called when an assertion fails. After printing an error
message, it will call abort(). abort() never returns, hence it has the
__dead2 attribute. Also add this attribute to __assert().
MFC after: 3 weeks
All builtins are now always found before a PATH search.
Most ash derivatives have an undocumented feature where the presence of an
entry "%builtin" in $PATH will cause builtins to be checked at that point of
the PATH search, rather than before looking at any directories as documented
in the man page (very old versions do document this feature).
I am removing this feature from sh, as it complicates the code, may violate
expectations (for example, /usr/bin/alias is very close to a forkbomb with
PATH=/usr/bin:%builtin, only /usr/bin/builtin not being another link saves
it) and appears to be unused (all the %builtin google code search finds is
in some sort of ash source code).
Note that aliases and functions took and take precedence above builtins.
Because aliases work on a lexical level they can only ever be overridden on
a lexical level (quoting or preceding 'builtin' or 'command'). Allowing
override of functions via PATH does not really fit in the model of sh and it
would work differently from %builtin if implemented.
Note: POSIX says special builtins are found before functions. We comply to
this because we do not allow functions with the same name as a special
builtin.
Silence from: freebsd-hackers@ (message sent 20101225)
Discussed with: dougb
all new devices added between our r211022 and their git revision
93ad03d60b5b18897030038234aa2ebae8234748
Also correct a Foxconn entry.
MFC after: 1 week
Stack creation code is changed to call _rtld_get_stack_prot() to get
the stack protection right. There is a race where thread is created
during dlopen() of dso that requires executable stacks. Then,
_rtld_get_stack_prot() may return PROT_READ | PROT_WRITE, but thread
is still not linked into the thread list. In this case, the callback
misses the thread stack, and rechecks the required protection
afterward.
Reviewed by: davidxu
