Andrew's problems with SCSI on some alphas- do not call isp_update
directly to update parameters- just mark them as being ready to
update for the next command- the system would just hang on a READ
CAPACITY for a drive. Really annoying because it wouldn't even timeout
(and it has a timeout) so either the SET PARAMETERS call was nuking
things or the f/w was really dropping the ball.
approved: jkh
Reviewed by: gallatin@freebsd.org
is gone as a define. We just don't support fast posting for anything less
than the 1240/1080/1280/12160 or Fibre Channel cards.
Put in support for CDB's larger than 12 bytes for parallel SCSI (up to 44
bytes are allowed).
Approved: jkh
Now libutil depends on libc.so.4, so needs to update the major version.
Without this, old binaries which use libutil and build with libc.so.3
will coredump on recent 4.0.
Solicited comment for cvs-committers and there seems to be no objection.
Approved by: jkh
might it confuse people, but it causes a warning message with
nroff, and no version history mentions a 1.2 version of FreeBSD.
If anything, a ``HISTORY'' section should show which version this
appeared in.
- Remove all the code intended to deal with experimental
C1010 revisions. This code got useless due to commercial
chip revisions having been fixed.
Fixes:
- Rewrite/rework the WSR condition handling.
Previous drivers snooped on the BUS through the SBDL IO
register and this has been discovered to trigger a spurious
SCSI parity error when WSR had been set by chip and cleared
by SCRIPTS prior to reading SBDL bit [0...7].
On the other hand, the C1010 does not use the SWIDE register
when synchronous data transfers are taking place and
requires a CHMOV (1) WHEN DATA_IN to be performed in order
to move to memory the residual byte when WSR is set and
the residual byte is useful data.
BTW, the new WSR handling by the driver is simpler.
- No longer attempt to read from SCRIPTS the SBDL register.
This is intended to avoid to be victimized again by any other
issue regarding the handling of this register by 8xx chips.
Miscellaneous:
- The driver is now able to handle the WSR + IGN RESIDUE
condition at the end of a DATA IN I/O without need of a
programmed interrupt. It is a minor? optimization.
- A few other minor cosmetic changes.
This driver version fixes notably a permanent SCSI parity
error condition at boot that can be triggerred due to recent
changes in cam_xpt.c between 1.79 and 1.80.
Changes in CAM/XPT are fine, but the new handling of the full
INQUIRY may trigger the driver problem when a target returned
an odd value in the `additionnal length' field of the INQUIRY
response.
The diff against previous driver version is large, but it
consists approximatively in:
- 350 lignes removed and not compiled in previous drivers
(They addressed experimental C1010 revisions)
- 250 lignes added or changed, half being comments or empty
lines.
So, in fact, the real changes are about 120 lines of source.
About 80 lines address SCRIPTS changes and about 40 lines
address C code changes.
Approved by: jkh
New WSR handling reviewed by Pamela Delaney <pam.delaney@lsil.com>
(For back-porting to Linux sym53c8xx driver 1.6x series)
Now libwrap depends on libc.so.4, so needs to update the major version.
Without this, old binaries which use libwrap and build with libc.so.3
will coredump on recent 4.0.
Approved by: jkh
Reviewed by: markm
S/Key authentication for ftpd was not working due to ftp implementation and
/etc/pam.conf missmatch.
So add ftpd entries into /etc/pam.conf.
Reported by: "Jose M. Alcaide" <jose@we.lc.ehu.es>
Approved by: jkh
Reviewed by: markm
-"ftp hostname:/path" was not working.
- IPv6 raw addr specification was not well supported, such as,
"ftp http://\[1:2:3:4:5:6:7:8:\]/index.html"
Approved by: jkh
