such as timeouts while probing a bus or testing for a feature, is
squelched. Also, error reporting is limited to 5 events per second,
because when an sdcard goes bad on a low-end embedded board, flooding
the console at high speed isn't helpful.
Original logging code contributed by Michal Meloun, but then I fancied
it up with squelching and ppsratecheck.
TI OMAP controllers which will return the reset-in-progress bit as zero if
you read the status register too fast after setting the reset bit.
The zero is apparently from a stale snapshot of the internal state presented
in the interface register, and leads to a false indication that the reset
is complete when it either hasn't started yet or is in-progress. The
workaround is to first loop until the bit is seen as asserted, then do the
normal loop waiting to see it de-asserted.
Submitted by: Michal Meloun <meloun@miracle.cz>
function parameters, the card has to be in transfer state. If it is in
the idle state, the commands are ignored. This caused us not to set
the proper parameters that we later assume to be present, leading to
downstream failures of the card / interface as our state machine
mismatches the card's.
Submitted by: Svatopluk Kraus <onwahe at gmail.com>, Michal Meloun
<meloun at miracle.cz>
While we don't support MCS, hole in received sequence numbers may mean
only PDU loss. While we don't support lost PDU recovery, terminate the
connection to avoid stuck commands.
While there, improve handling of sequence numbers wrap after 2^32 PDUs.
MFC after: 2 weeks
sheet, RX filter should be disabled before programming.
Previously it was clearing wrong bits so RX filter was not
disabled in RX filter configuration.
Reported by: brad@OpenBSD.org
This allows the Grant-table code to attach directly to the xenpv bus,
allowing us to remove the grant-table initialization done in xenpv.
Sponsored by: Citrix Systems R&D
Mave the grant table code into the dev/xen folder in preparation for turning
it into a device using the newbus interface. This is just code motion, no
functional changes.
Sponsored by: Citrix Systems R&D
When running as a Xen PVH Dom0 we need to add custom buses that override
some of the functionality present in the ACPI PCI Bus and the PCI Bus. We
currently override the ACPI PCI Bus, but not the PCI Bus, so add a new
override for the PCI Bus and share the generic functions between them.
Reported by: David P. Discher <dpd@dpdtech.com>
Sponsored by: Citrix Systems R&D
conf/files.amd64:
- Add the new files.
x86/xen/xen_pci_bus.c:
- Generic file that contains the PCI overrides so they can be used by the
several PCI specific buses.
xen/xen_pci.h:
- Prototypes for the generic overried functions.
dev/xen/pci/xen_pci.c:
- Xen specific override for the PCI bus.
dev/xen/pci/xen_acpi_pci.c:
- Xen specific override for the ACPI PCI bus.
o Move similar block/networking methods to common file
o Follow r275640 and correct MMIO registers width
o Pass value to MMIO platform_note method.
Sponsored by: DARPA, AFRL
There are two main parts to get it to work, 1) most of the register
accesses need to be word sized, other than the config register which
needs to be byte aligned, and 2) we don't need the platform driver
for this to work on the Foundation Model, allow it to be NULL.
Differential Revision: https://reviews.freebsd.org/D1240
Reviewed by: bryanv
Sponsored by: The FreeBSD Foundation
adapters. Set the pack boundary for T5 cards to be the same as the
PCIe max payload size. The chip likes it this way.
In this revision the driver allocate rx buffers that align on both
boundaries. This is not a strict requirement and a followup commit
will switch the driver to a more relaxed allocation strategy.
MFC after: 2 weeks
re-using a hardware propritary transfer descriptor, PTD, in USB host
mode. If the PTD's are recycled too quickly, it has been observed that
the hardware simply fails to schedule the requested job or resets
completely disconnecting all devices.
Always include the card human readable name. We support ~270 cards and
at ~20 bytes each, this bloats things by only ~5k. Retain the
PCMCIA_CARD vs PCMCIA_CARD_D distinction, though, in case this is
intolerable.
from the FreeBSD network code. The flag is still kept around in the
"sys/mbuf.h" header file, but does no longer have any users. Instead
the "m_pkthdr.rsstype" field in the mbuf structure is now used to
decide the meaning of the "m_pkthdr.flowid" field. To modify the
"m_pkthdr.rsstype" field please use the existing "M_HASHTYPE_XXX"
macros as defined in the "sys/mbuf.h" header file.
This patch introduces new behaviour in the transmit direction.
Previously network drivers checked if "M_FLOWID" was set in "m_flags"
before using the "m_pkthdr.flowid" field. This check has now now been
replaced by checking if "M_HASHTYPE_GET(m)" is different from
"M_HASHTYPE_NONE". In the future more hashtypes will be added, for
example hashtypes for hardware dedicated flows.
"M_HASHTYPE_OPAQUE" indicates that the "m_pkthdr.flowid" value is
valid and has no particular type. This change removes the need for an
"if" statement in TCP transmit code checking for the presence of a
valid flowid value. The "if" statement mentioned above is now a direct
variable assignment which is then later checked by the respective
network drivers like before.
Additional notes:
- The SCTP code changes will be committed as a separate patch.
- Removal of the "M_FLOWID" flag will also be done separately.
- The FreeBSD version has been bumped.
MFC after: 1 month
Sponsored by: Mellanox Technologies
- Add support for GEOM direct completion. Depending on the benchmark,
this tends to give a ~30% improvement w.r.t IOPs and BW.
- Remove an invariants check in the strategy routine. This assertion
is caught later on by an existing panic.
- Rename and resort various related functions to make more sense.
MFC after: 1 month
sending not ready data:
o Add new flag to pru_send() flags - PRUS_NOTREADY.
o Add new protocol method pru_ready().
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
o Introduce a notion of "not ready" mbufs in socket buffers. These
mbufs are now being populated by some I/O in background and are
referenced outside. This forces following implications:
- An mbuf which is "not ready" can't be taken out of the buffer.
- An mbuf that is behind a "not ready" in the queue neither.
- If sockbet buffer is flushed, then "not ready" mbufs shouln't be
freed.
o In struct sockbuf the sb_cc field is split into sb_ccc and sb_acc.
The sb_ccc stands for ""claimed character count", or "committed
character count". And the sb_acc is "available character count".
Consumers of socket buffer API shouldn't already access them directly,
but use sbused() and sbavail() respectively.
o Not ready mbufs are marked with M_NOTREADY, and ready but blocked ones
with M_BLOCKED.
o New field sb_fnrdy points to the first not ready mbuf, to avoid linear
search.
o New function sbready() is provided to activate certain amount of mbufs
in a socket buffer.
A special note on SCTP:
SCTP has its own sockbufs. Unfortunately, FreeBSD stack doesn't yet
allow protocol specific sockbufs. Thus, SCTP does some hacks to make
itself compatible with FreeBSD: it manages sockbufs on its own, but keeps
sb_cc updated to inform the stack of amount of data in them. The new
notion of "not ready" data isn't supported by SCTP. Instead, only a
mechanical substitute is done: s/sb_cc/sb_ccc/.
A proper solution would be to take away struct sockbuf from struct
socket and allow protocols to implement their own socket buffers, like
SCTP already does. This was discussed with rrs@.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
Call to the driver-specific ioctl used to process ioctl number
that will lead to the out-of-bounds access to the ioctl handler
array.
PR: 193367
Approved by: kib
MFC after: 1 week
This allows one to make a kernel module to tune the
number of queues before the driver loads.
This is needed so that a module at SI_SUB_CPU can set
tunables for these drivers to take. Otherwise getenv
is called too early by the TUNABLE macros.
Reviewed by: smh
Phabric: https://reviews.freebsd.org/D1149
