High-speed USB HUB by resetting the transaction translator (TT)
before trying re-enumeration. Also when clear-stall fails multiple times
try a re-enumeration.
Suggested by: Trevor Blackwell
MFC after: 14 days
This brings USB bus more in line with how newbus is supposed to be used.
Also, because of the two-pass probing the following message was produced
by devd in default configuration when almost any USB device was
connected:
Unknown USB device: vendor <> product <> bus <>
This should be fixed now.
Note that many USB device drivers pass some information from probe
method to attach method via ivars. For this to continue working we rely
on the fact that the subr_bus code calls probe method of a winning driver
again before calling its attach method in the case where multiple
drivers claim to support a device. This is done because device
description is set in successful probe methods and we want to get a correct
device description from a winning driver. So now this logic is re-used
for setting ivars too.
Reviewed by: hselasky
MFC after: 1 month
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
will generate a short terminated USB transfer if
the maximum NCM frame size is greater than what
the driver can handle.
Reported by: Matthias Benesch
MFC after: 7 days
Approved by: thompsa (mentor)
bus driver at detach, hence ehci_detach() does exactly this since r199718.
Submitted by: Luiz Otavio O Souza
MFC after: 7 days
Approved by: thompsa (mentor)
SCSI status errors to CAM (that was wrong, as it too often turned retriable
wire errors into non-retriable REQUEST SENSE errors), do it only for STALL
errors on control pipe of the CBI devices. STALL on control pipe is just
a one of the ways to report error for CBI devices.
PR: usb/150401, usb/154593.
Reviewed by: hselasky
MFC after: 1 week
- Add more fields for USB device and host mode
- Add more information to USB PF header so that decoding
can easily be done by software analyzer tools like
Wireshark.
- Optimise usbdump to display USB streams in text format
more efficiently.
- Software using USB PF must be recompiled after
this commit, due to structure changes.
MFC after: 7 days
Approved by: thompsa (mentor)
report descriptor information, sysctl utility
will show it for us.
- Modify sysctl node description to make it more
understanable.
Found by: Alexander Best <arundel@freebsd.org>
Submitted by: Eygene Ryabinkin <rea@freebsd.org>
MFC after: 14 days
Approved by: thompsa (mentor)
value is updated after that we read it in the queue-head. This patch can
fix problems with BULK timeouts. The issue was found on a Nvidia chipset.
MFC after: 14 days
Approved by: thompsa (mentor)
means of allowing vendor specific interface class for audio and MIDI devices.
- Add new quirks for this. The vendor and product list in OpenBSD's
dev/usb/umidi_quirks.c was used as reference.
MFC after: 14 days
Approved by: thompsa (mentor)
While updating Tx stats, already freed node could be referred and cause
page fault. To avoid such panic, spool Tx stats in driver's softc. Then,
on every ratectl interval, grab node though ieee80211_iterate_nodes() and
update ratectl stats.
* Simplify some code in run_iter_func().
* Fix typo
* Use memset instead of bzero (hselasky @)
PR: kern/153938
Submitted by: PseudoCylon <moonlightakkiy@yahoo.ca>
Approved by: thompsa (mentor)
Drivers which rely on net80211 to create the beacon need to call
ieee80211_beacon_update() on iv_update_beacon() calls. This is required
that certain bits, e.g. TIM, get updated. A call to ieee80211_beacon_alloc()
is not enough because it does not care about flags which can only change
during runtime. By design a beacon is supposed to be allocated only once
while moving into RUN state.
To handle all possible calls to iv_update_beacon() the run_updateslot()
function has been revived and run_updateprot() has been added.
run_updateslot() handles slot time changes and run_updateprot() changes
to protection, both can change while nodes associate/leave.
Submitted by: Alexander Zagrebin <alex at zagrebin.ru>,
PseudoCylon <moonlightakkiy atyahoo.ca>
MFC after: 3 weeks
- use device_printf() instead of printf() to give more accurate warnings.
- use memcpy() instead of bcopy().
- add missing #if's for non-FreeBSD compilation.
Approved by: thompsa (mentor)
error address on a decoding error to unlatch it and to allow
us to print a better diagnostics message. This also has the
side effect of clearing the condition, which prevents an
interrupt storm.
