and keepalive in the sysctl MIB. Provide tunables to change some of
these parameters. These are supposed to be setup by the firmware so
these tunables are for experimentation only.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
doesn't seem to have one. This lets the driver recover automatically
from incomplete firmware upgrades (panic, reboot, power loss, etc. in
the middle of an upgrade).
MFC after: 2 weeks
Sponsored by: Chelsio Communications
- Deal with changes to port_type, and not just port_mod when a
transceiver is changed. This fixes hot swapping of transceivers of
different types (QSFP+ or QSA or QSFP28 in a QSFP28 port, SFP+ or
SFP28 in a SFP28 port, etc.).
- Always refresh media information for ifconfig if the port is down.
The firmware does not generate tranceiver-change interrupts unless at
least one VI is enabled on the physical port. Before this change
ifconfig diplayed potentially stale information for ports that were
administratively down.
- Always recalculate and reapply L1 config on a transceiver change.
- Display PAUSE settings in ifconfig. The driver sysctls for this
continue to work as well.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
the "effective MSS" for the connection. The chip expects it this way.
Submitted by: Krishnamraju Eraparaju @ Chelsio
MFC after: 3 days
Sponsored by: Chelsio Communications
Do not attempt to initialize netmap queues that are already initialized
or aren't supposed to be initialized. Similarly, do not free queues
that are not initialized or aren't supposed to be freed.
PR: 217156
Sponsored by: Chelsio Communications
- For HMAC requests, construct a special input buffer to request an empty
hash result.
- For plain cipher requests and requests that chain an AES cipher with an
HMAC, fail with EINVAL if there is no cipher payload. If needed in
the future, chained requests that only contain AAD could be serviced as
HMAC-only requests.
- For GCM requests, the hardware does not support generating the tag for
an AAD-only request. Instead, complete these requests synchronously
in software on the assumption that such requests are rare.
Sponsored by: Chelsio Communications
The adapter firmware in general does not accept PDUs larger than 64k - 1
bytes in size. Sending crypto requests larger than this size result in
hangs or incorrect output, so reject them with EFBIG. For requests
chaining an AES cipher with an HMAC, the firmware appears to require
slightly smaller requests (around 512 bytes).
Sponsored by: Chelsio Communications
The latest firmware has a number of link related fixes, support for a
new custom card, and the fix for a bug that affected rate limiting on
FreeBSD.
Obtained from: Chelsio Communications
MFC after: 1 week
Sponsored by: Chelsio Communications
The ccr(4) driver supports use of the crypto accelerator engine on
Chelsio T6 NICs in "lookaside" mode via the opencrypto framework.
Currently, the driver supports AES-CBC, AES-CTR, AES-GCM, and AES-XTS
cipher algorithms as well as the SHA1-HMAC, SHA2-256-HMAC, SHA2-384-HMAC,
and SHA2-512-HMAC authentication algorithms. The driver also supports
chaining one of AES-CBC, AES-CTR, or AES-XTS with an authentication
algorithm for encrypt-then-authenticate operations.
Note that this driver is still under active development and testing and
may not yet be ready for production use. It does pass the tests in
tests/sys/opencrypto with the exception that the AES-GCM implementation
in the driver does not yet support requests with a zero byte payload.
To use this driver currently, the "uwire" configuration must be used
along with explicitly enabling support for lookaside crypto capabilities
in the cxgbe(4) driver. These can be done by setting the following
tunables before loading the cxgbe(4) driver:
hw.cxgbe.config_file=uwire
hw.cxgbe.cryptocaps_allowed=-1
MFC after: 1 month
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D10763
Invoke any identify routines of child drivers during attach before attaching
children, and delete any remaining devices after deleting ports.
MFC after: 1 month
Sponsored by: Chelsio Communications
- Do not leak the adapter lock in sysctl_autoneg.
- Accept only 0 or 1 as valid settings for autonegotiation.
- A fixed speed must be requested by the driver when autonegotiation is
disabled otherwise the firmware will reject the l1cfg command. Use
the top speed supported by the port for now.
MFC after: 3 days
Sponsored by: Chelsio Communications
the TOE. For now this capability is always enabled in kernels with
options RATELIMIT. t4_tom will check if_capenable once the base driver
gets code to support rate limiting for any socket (TOE or not).
This was tested with iperf3 and netperf ToT as they already support
SO_MAX_PACING_RATE sockopt. There is a bug in firmwares prior to
1.16.45.0 that affects the BSD driver only and results in rate-limiting
at an incorrect rate. This will resolve by itself as soon as 1.16.45.0
or later firmware shows up in the driver.
Relnotes: Yes
Sponsored by: Chelsio Communications
- Create a new file, t4_sched.c, and move all of the code related to
traffic management from t4_main.c and t4_sge.c to this file.
- Track both Channel Rate Limiter (ch_rl) and Class Rate Limiter (cl_rl)
parameters in the PF driver.
- Initialize all the cl_rl limiters with somewhat arbitrary default
rates and provide routines to update them on the fly.
- Provide routines to reserve and release traffic classes.
MFC after: 1 month
Sponsored by: Chelsio Communications
available starting with T6. The values in the timer holdoff registers
are multiplied by the scaling factor before use.
dev.<nexus>.<n>.holdoff_timers shows the final values of the
timers in microseconds.
MFC after: 1 week
Sponsored by: Chelsio Communications
(and accurate).
T4 and later have an extra bit for page shift so the maximum page size
is 8TB (shift of 12 + 31) instead of 128MB (12 + 15). This saves space
in the chip's PBL (physical buffer list) when registering very large
memory regions.
MFC after: 3 days
Sponsored by: Chelsio Communications
the thread that deals with socket state changes. This eliminates
various bad races with the ithread.
Submitted by: KrishnamRaju ErapaRaju @ Chelsio (original version)
MFC after: 3 days
Sponsored by: Chelsio Communications
inpcb. t4_tom detaches the inpcb from the toepcb as soon as the
hardware is done with the connection (in final_cpl_received) but the
socket is around as long as the cm_id and the rest of iWARP state is.
This fixes an intermittent NULL dereference during abort.
Submitted by: KrishnamRaju ErapaRaju @ Chelsio
MFC after: 3 days
Sponsored by: Chelsio Communications
ULPs can set a qp's state to ERROR and then post a work request on the
sq and/or rq. When the reply for that work request comes back it is
guaranteed that all previous work requests posted on that queue have
been drained.
Obtained from: Chelsio Communications
MFC after: 3 days
Sponsored by: Chelsio Communications
registered. T4/5/6 have no internal limit on this size. This is
probably a copy paste from the T3 iw_cxgb driver.
MFC after: 3 days
Sponsored by: Chelsio Communications
Sockets representing the TCP endpoints for iWARP connections are
allocated by the ibcore module. Before this revision they were closed
either by the ibcore module or the iw_cxgbe hardware driver depending on
the state transitions during connection teardown. This is error prone
and there were cases where both iw_cxgbe and ibcore closed the socket
leading to double-free panics. The fix is to let ibcore close the
sockets it creates and never do it in the driver.
- Use sodisconnect instead of soclose (preceded by solinger = 0) in the
driver to tear down an RDMA connection abruptly. This does what's
intended without releasing the socket's fd reference.
- Close the socket in ibcore when the iWARP iw_cm_id is destroyed. This
works for all kinds of sockets: clients that initiate connections,
listeners, and sockets accepted off of listeners.
Reviewed by: Steve Wise @ Open Grid Computing, hselasky@
MFC after: 3 days
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D9796
'-n' to tell the driver to create _up to_ 'n' queues if enough cores are
available. For example, setting hw.cxgbe.nrxq10g="-32" will result in
16 queues if the system has 16 cores, 32 if it has 32.
There is no change in the default number of queues of any type.
MFC after: 1 week
Sponsored by: Chelsio Communications
- Check for Chelsio vendor ID in probe routines.
- Fail attach instead of faulting if pci_find_dbsf() doesn't find a
device.
PR: 216539
Reported by: asomers
Tested by: Dave Baukus <daveb@spectralogic.com>
MFC after: 3 days
Sponsored by: Chelsio Communications
undo_offload_socket() is only called by t4_connect() during a connection
setup failure, but t4_connect() still owns the TOE PCB and frees ita
after undo_offload_socket() returns. Release a reference in
undo_offload_socket() resulted in a double-free which panicked when
t4_connect() performed the second free. The reference release was
added to undo_offload_socket() incorrectly in r299210.
MFC after: 1 week
Sponsored by: Chelsio Communications
Active Open:
- Save the socket's vnet at the time of the active open (t4_connect) and
switch to it when processing the reply (do_act_open_rpl or
do_act_establish).
Passive Open:
- Save the listening socket's vnet in the driver's listen_ctx and switch
to it when processing incoming SYNs for the socket.
- Reject SYNs that arrive on an ifnet that's not in the same vnet as the
listening socket.
CLIP (Compressed Local IPv6) table:
- Add only those IPv6 addresses to the CLIP that are in a vnet
associated with one of the card's ifnets.
Misc:
- Set vnet from the toepcb when processing TCP state transitions.
- The kernel sets the vnet when calling the driver's output routine
so t4_push_frames runs in proper vnet context already. One exception
is when incoming credits trigger tx within the driver's ithread. Set
the vnet explicitly in do_fw4_ack for that case.
MFC after: 3 days
Sponsored by: Chelsio Communications
a linuxkpi style device is expected. If OFED/linuxkpi actually starts
using this field then we'll have to figure out whether to create fake
devices for these drivers or have linuxkpi deal with NULL device.
This mismatch was first reported as part of D6585.
all public firmwares for all chips since the last release (1.15.37.0)
follows (it's a straight copy-paste from the Release Notes for the
12/30/2016 Unified Wire release on Chelsio's website).
T6 Firmware
++++++++++++
Version : 1.16.26.0
Date : 12/28/2016
Fixes
-----
BASE:
- Max number of egress and control queues adjusted to accomodate
co-processor mode queues.
- Fixed intermittent DDR3/4 ECC errors.
- Fixed a traffic stall when ETS BW is configured as 0%.
- Max number of ethctrl queue in VF set to 1.
ETH:
- Added a new config file option 'speed' under port section to set the
port speed. Use only when auto negotiation is off.
- FEC option removed from firmware config file. cxgbtool can be used to
change the fec setting.
- CPL_TX_TNL_LSO cpl handling added in ETH_TX_PKT_VM handler. This fixes
large tunnel tcp packet support for VxLAN.
Version : 1.16.22.0
Date : 12/05/2016
Fixes
-----
BASE:
- fw_port_type updated in fw API to match kernel.org definitions.
- Saved power by disaling unused MAC lanes.
- Configures correct power bin.
- Enhanced DDR4 performance.
- Enabled interrupts.
- Fixed an issue where filter rule for 'unicast hash' is not working.
ETH:
- Disabled auto negotiation by default because most of 100G switches do
not support AN as of today.
- Fixed flow control not getting disabled problem.
- Fixed an issue where port0 doesn't come up sometimes.
- Fixed 10G link not coming up issue.
- Fixed an issue with promiscuous mode when dcbx disabled.
OFLD:
- Fixed a connection stuck issue when abort is received during out of tx
pages backpressure.
ENHANCEMENTS
------------
BASE:
- Added inline TLS mode support.
Version : 1.16.12.0
Date : 11/11/2016
ENHANCEMENTS
------------
BASE:
- Added T6 support.
- Added T6 1G/10G/25G/40G/100G link speeds.
- Added T6 co-processor mode crypto support.
- Added facility to increase link AN+AEC timeout.
OFLD:
- Added support for all T5 offload protocols except FCoE.
iSCSI:
- iscsi completion moderation enabled.
=======================================================================
T5 Firmware
++++++++++++
Version : 1.16.26.0
Date : 12/28/2016
FIXES
-----
BASE:
- Max number of ethctrl queue in VF set to 1.
Version : 1.16.22.0
Date : 12/05/2016
FIXES
-----
BASE:
- Fixed an issue where filter rule for 'unicast hash' is not working.
ETH:
- Fixed an issue with promiscuous mode when dcbx disabled.
ENHANCEMENTS
------------
ETH:
- Added 40G-KR support.
Version : 1.16.12.0
Date : 11/11/2016
FIXES
-----
BASE:
- Fixed multiple issues related with VFs FLR processing.
- Fixed channel assignment based on number of ports in adapter.
- Fixed a crash when VM having PF assigned as passthrough mode is
rebooted.
- Handled 2nd HELLO command from the same PF without seeing BYE from the
same PF and if that is the only PF.
- A warning is printed in firmware log if PCI-E cookie generation is
enabled in serial initialization file.
- Fixed multiple issues related with Filtering.
- Enabled DSGL memory write for iscsi and rdma.
- Added new FW_PARAMS_CMD[DEV] options to retrieve Serial Configuration
and VPD version numbers.
- Fixed an issue where LVDS output was not getting enabled using vpd.
DCBX:
- Fixed DCBX CEE Incorrect class to pririty mapping.
- Fixed incorrect interpretation of DCBX IEEE PFC.
ETH:
- Adjusted the link related delay timings according to the QSFP spec.
- Improved 40G link bringup time with few switches.
OFLD:
- Do not reserve qp/cq if rdma capability is not enabled.
- Fixed an issue where approx 1600+ TOE connections were causing a
firmware fatal error.
FOiSCSI:
- Fixed an issue where unloading foiscsi driver causes mailbox timeout.
ENHANCEMENTS
------------
BASE:
- Added 10G KR/KX support.
- Added T540-BT adapter support.
- Added 4 new rss key modes for PFs and VFs.
OFLD:
- Added new WR FW_RI_FR_NSMR_TPTE_WR to improve fast MR write
performance in RDMA.
Version : 1.16.5.0
Date : 10/26/2016
FIXES
-----
BASE:
- Fixed multiple issues where FLR from multiple VFs can cause firmware
crash.
- Fixed channel assignment based on number of ports in adapter.
- Fixed the HELLO command master force api to handle the 2nd HELLO
correctly without getting BYE from the PF driver.
- Added facility to retrieve Serial configuration and VPD version. Two
new FW_PARAMS_CMD[DEV] options added to retrieve these values.
- Fixed multiple issues where FLR from multiple VFs are not completing.
- Added new RSS hash secret key modes.
- Fixed an issue where LVDS output was not getting enabled using vpd.
DCBX:
- Fixed an issue where iscsi tlv is sent incorrectly to host (DCBX CEE).
- Fixed an issue where app priority values are not handled correctly
in fw (DCBX IEEE).
ETH:
- Adjusts the link related delay timings according to the QSFP spec.
- Changed 2.5G mac speed bit to 25G mac speed bit in fw API.
- Improvement in 40G link bringup time with few switches.
OFLD:
- Do not reserve qp/cq if rdma capability is not enabled.
- Fixed an issue where approx 1600+ TOE connections were causing a
firmware fatal error.
- Fixed DSGL memory write in T5. Now iwarp and iscsi can use DSGL to do
memory write.
- Fixed multiple issues in hash filter mode where incorrect protocol
mask was getting used and affecting hash filter functionality.
- New fastpath WR FW_RI_FR_NSMR_TPTE_WR (with fully populated TPTE) is
added for small REG_MR operations.
FOiSCSI:
- Fixed an issue in foiscsi recovery path.
- Fixed an issue where foiscsi (in VM in PCIE passthrough mode) didn't
come up after VM FLR.
ENHANCEMENTS
------------
ETH:
- Implemented 1G/10G KR/KX ability.
- Implemented T540-BT adapter support.
=======================================================================
T4 Firmware
+++++++++++
Version : 1.16.12.0
Date : 11/11/2016
FIXES
-----
BASE:
- Fixed an issue where reading temperature sesors using ldst command
causes mailbox timeout.
- Added new FW_PARAMS_CMD[DEV] options to retrieve Serial Configuration
and VPD version numbers.
ETH:
- Fixed DCBX CEE Incorrect class to pririty mapping.
FOiSCSI:
- Fixed an issue where unloading foiscsi driver causes mailbox timeout.
MFC after: 3 days
Sponsored by: Chelsio Communications
- Update struct link_settings and associated shared code.
- Add tunables to control FEC and autonegotiation. All ports inherit
these values as their initial settings.
hw.cxgbe.fec
hw.cxgbe.autoneg
- Add per-port sysctls to control FEC and autonegotiation. These can be
modified at any time.
dev.<port>.<n>.fec
dev.<port>.<n>.autoneg
MFC after: 3 days
Sponsored by: Chelsio Communications
- Disable features that are not supported or not used on FreeBSD.
- Increase the RSS table slice per interface.
- Increase the share of the TCAM reserved for filtering.
MFH: 2 weeks
Sponsored by: Chelsio Communications
There are 4 independent knobs in T5+ chips to include or exclude PAUSE
frames from the "total frames" and "multicast frames" counters in either
direction. This change lets the driver deal with any combination of
these settings.
contiguous regions in an mbuf chain.
If the payload of an mbuf ends at a page boundary count_mbuf_nsegs would
incorrectly consider the next mbuf's payload physically contiguous based
solely on a KVA comparison.
MFC after: 1 week
Sponsored by: Chelsio Communications
