(mainly the 3Com 3c996B/BCM5701).
For some reason that I don't fully understand, the 5701 signals PCS
encoding errors as though they were link change events, i.e. the 'link
state changed' bit in the status word of the status block is updated
and an interrupt is generated. This would cause the bge_tick() function
to be invoked and a "gigabit link up" message to be printed on the console.
To avoid this, the interrupt handler now checks the MAC status register
when a link change interrupt is triggered, and it will only call the
bge_tick() function if the 'PCS encoding error detected' bit is clear.
(This change should have no effect on copper NICs since this bit can
only ever be set in TBI mode. I do not know how it affects 5704 NICs
with a BCM8002 SERDES PHY.)
Special thanks to: Sherry Rogers at UCB for allowing me access to one
of their traffic monitor boxes so I could diagnose this problem.
- MN-110 10/100 USB ethernet (ADMtek Pegasus II, if_aue)
- MN-120 10/100 cardbus (ADMtek Centaur-C, if_dc)
- MN-130 10/100 PCI (ADMtek Centaur-P, if_dc)
Also update dc(4) man page to mention support for MN-120 and MN-130.
* Always use polled mode. The intr approach did not work for many
controllers and required the hw.acpi.ec.event_driven workaround.
* Only use an edge (not level) triggered GPE handler
* Add sc->ec_mtx for locking operations to a single EC. There were
many race conditions earlier between an SCI event and EcRead/Write.
* Use 1 ms as the global lock timeout
* Only acquire global lock if _GLK != 0
* Update EcWaitEvent to use an incremental backoff delay in its
poll loop. Wait 50 ms max instead of 10. Most ECs respond
in < 5 us (50 us when heavily loaded). However, some time out
occasionally even with a 10 ms timeout. For delays past 1 ms, use
msleep instead of DELAY to give SCI interrupts a chance to occur.
* Add EcCommand to send a command and wait for the appropriate event.
* The hw.acpi.ec.event_driven tunable is no longer applicable and
has been removed.
Ideas from: Linux
bus_dma_tag_create. We need to be sure that our packets are
kept in-sequence (that's how ATM is supposed to work) and
therefor use BUS_DMA_NOWAIT in all calls to bus_dmamap_load.
For memory allocated with bus_dmamem_alloc the use of anything
other than NULL arguments for the locking is anyway bogus because
this memory never should need bouncing and hence the load should never
be defered.
Allow the receipt of OAM and RM cells on raw connections. Caveat: it seems
that RM cells are still processed by the hardware even when we open the
connection as UBR.
extra trailing space.
- Don't bother probing a generic ISA bus device if isab0 already exists.
Some BIOSes place an ACPI psuedo-device with the HID of a generic ISA bus
device under the PCI-ISA bridge device. This is not the best solution
but will work for now. The isa bus driver only allows for one ISA bus
anyways.
ACPI nodes with the plug and play ID's defined for a "Generic ISA Bus
Device" as defined in section 10.7 of the ACPI 2.0 specification. This
gives machines like the Libretto that contain a fake ISA bus that is not
connected via a PCI-ISA bridge an ISA bus for ISA devices to attach to.
Tested by: markm
- Factor out code common to all ISA bridge drivers attach methods into a
isab_attach() function.
- Rename the PCI-ISA bridge driver's attach function to pci_isab_attach()
and have it call isab_attach().
the bulk out buffer size to 16 bytes. The bulk out endpoint descriptor
reports 32 bytes, but if you use this value, data will get dropped.
Reviewed/approved by: scottl
to have this driver working on sparc64. It still needs to be made
endian-clean before it can work there.
Special thanks to dragonk@evilcode.net for sending me a dc(4) card so
that I was able to do this work.
Many cheers to all the people that tested this change, thanks to them,
this change shouldn't break anything :-).
Tested by: marcel (i386 and ia64), ru (i386), wilko (alpha),
mbr (i386), wpaul (i386) and
Will Saxon <WillS@housing.ufl.edu> (i386)
tested for playback.
* modify device name strings for ich chips to better conform with their
common names.
* remove superflous 'AC97 controller' from nforce device names.
MFC after: 1 week
forced to do slightly bogus power state manipulation. However, this
is one of those features that is preventing further progress, so mark
them as BURN_BIRDGES like I did for the drivers in sys/dev/...
This, like the other change, are a no-op unless you have BURN_BRIDGES
in your kernel.
However, they are presently necessary due to bigger bogusness in the
pci bus layer not doing the right thing on suspend/resume or on
initial device probe. This is exactly the sort of thing that the
BURN_BRIDGES option was invented for. Mark all of them as
BURN_BRIDGES. As soon as I have the powerstate stuff properly
integrated into the pci bus code, I intend to remove all these
workarounds.
disabled.
- Change the apm driver to match the acpi driver's behavior by checking to
see if the device is disabled in the identify routine instead of in the
probe routine. This way if the device is disabled it is never created.
Note that a few places (ips(4), Alpha SMP) used "disable" instead of
"disabled" for their hint names, and these hints must be changed to
"disabled". If this is a big problem, resource_disabled() can always be
changed to honor both names.
careful to call all map_load calls with BUS_DMA_NOWAIT because we
really don't want some PDUs to wait while others go out - ATM guarantees
the ordering of cells and also of PDUs (within one VC, that is). With
BUS_DMA_NOWAIT bus_dmamap_load should never return EINPROGRESS.
Make the tag used for transmission buffers one larger than the maximum
AAL5 PDU (65535). This is needed, because all PDU sizes need to be round
up to multiple of four for the card and PDUs that are just below the
maximum size will be rounded up to 65536
real SATA disks now that I can test it.
Add support for the SiI 3112 SATA chip using memory mapped I/O.
Update the support for the SiI 0680 to use the memio interface as well.
Sponsored by: David Leimbach <leimy2k@mac.com> (3112 based controller)
Sponsored by: FreeBSD Systems (www.FreeBSDsystems.com) (SATA disks)
Add two new arguments to bus_dma_tag_create(): lockfunc and lockfuncarg.
Lockfunc allows a driver to provide a function for managing its locking
semantics while using busdma. At the moment, this is used for the
asynchronous busdma_swi and callback mechanism. Two lockfunc implementations
are provided: busdma_lock_mutex() performs standard mutex operations on the
mutex that is specified from lockfuncarg. dftl_lock() is a panic
implementation and is defaulted to when NULL, NULL are passed to
bus_dma_tag_create(). The only time that NULL, NULL should ever be used is
when the driver ensures that bus_dmamap_load() will not be deferred.
Drivers that do not provide their own locking can pass
busdma_lock_mutex,&Giant args in order to preserve the former behaviour.
sparc64 and powerpc do not provide real busdma_swi functions, so this is
largely a noop on those platforms. The busdma_swi on is64 is not properly
locked yet, so warnings will be emitted on this platform when busdma
callback deferrals happen.
If anyone gets panics or warnings from dflt_lock() being called, please
let me know right away.
Reviewed by: tmm, gibbs
interrupt to be used for a device. This is intended solely for internal
use of PCI bus implementations, and exists so that PCI bus drivers
implementing special interrupt assignment methods which require
additional work at the bus level to work right can be easily derived
from the generic driver (or any other one) without resorting to hacks.
It will be used in the sparc64 ofw_pcibus driver, which will be
committed shortly.
Make use of this method in the generic implementation, and add it to
the method table of bus drivers derived from the PCI one.
Reviewed by: imp, -hackers
are some Sun PCI devices around which bogusly set intpin to 0, although
they use the intline mechanism; this allows the device driver to correct
that.
Reviewed by: imp
