A while back, Warner changed the PCI bus code to reserve resources when
enumerating devices and simply give devices the previously allocated
resources when they call bus_alloc_resource(). This ensures that address
ranges being decoded by a BAR are always allocated in the nexus0 device
(or whatever device the PCI bus gets its address space from) even if a
device driver is not attached to the device. This patch extends this
behavior further:
- To let the PCI bus distinguish between a resource being allocated by
a device driver vs. merely being allocated by the bus, use
rman_set_device() to assign the device to the bus when it is owned
by the bus and to the child device when it is allocated by the child
device's driver. We can now prevent a device driver from allocating
the same device twice. Doing so could result in odd things like
allocating duplicate virtual memory to map the resource on some
archs and leaking the original mapping.
- When a PCI device driver releases a resource, don't pass the request
all the way up the tree and release it in the nexus (or similar device)
since the BAR is still active and decoding. Otherwise, another device
could later allocate the same range even though it is still in use.
Instead, deactivate the resource and assign it back to the PCI bus
using rman_set_device().
- pci_delete_resource() will actually completely free a BAR including
attemping to disable it.
- Disable BAR decoding via the command register when sizing a BAR in
pci_alloc_map() which is used to allocate resources for a BAR when
the BIOS/firmware did not assign a usable resource range during boot.
This mirrors an earlier fix to pci_add_map() which is used when to
size BARs during boot.
- Move the activation of I/O decoding in the PCI command register into
pci_activate_resource() instead of doing it in pci_alloc_resource().
Previously we could actually enable decoding before a BAR was
initialized via pci_alloc_map().
Glanced at by: bsdimp
RH0 was deprecated by RFC 5095.
While most of the code had been disabled by #if 0 already, leave a
bit of infrastructure for possible RH2 code and a log message under
BURN_BRIDGES in case a user still tries to send RH0 packets.
Reviewed by: gnn (a bit back, earlier version)
Previosly readdir missed some directory entries because there was
no space for them in current uio but directory stream offset
was advanced nevertheless.
jhb has discoved the issue and provided a test-case.
Reviewed by: bde
Approved by: jhb (mentor)
locale-based failures on systems where the "C" locale is so permissive
that it cannot possibly fail. In particular, this fixes a test
problem on Cygwin.
(This is part of a larger changeset which is intended to reduce diff only,
thus some prototypes were left intact since they will be changed in the
future).
Verified with: md5(1)
vfsopt and the vfs_buildopts function public, and add some new fields
to struct vfsopt (pos and seen), and new functions vfs_getopt_pos and
vfs_opterror.
Further extend the interface to allow reading options from the kernel
in addition to sending them to the kernel, with vfs_setopt and related
functions.
While this allows the "name=value" option interface to be used for more
than just FS mounts (planned use is for jails), it retains the current
"vfsopt" name and <sys/mount.h> requirement.
Approved by: bz (mentor)
as a handler.
The variable was exported only for debugging, but there is little reason
to do it now that the timekeeping is supported by various other variables.
For the time being just comment out the sysctl, but I think this
should go away.
of sysctl_variables.
I would also remove it from the VNET record but I am unsure if
there is any ABI issue -- so for the time being just mark it as
unused in ip_fw.h, and then we will collect the garbage at some
appropriate time in the future.
MFC after: 3 days
operation is known and to retry or fail accordingly to that
outcome. This fixes the problem with namespace traversing
programs failing with random ENOENT errors if someone just
happened to try to unmount that same filesystem at the same
time.
Reported by: dhw
Reviewed by: kib, attilio
Sponsored by: Juniper Networks, Inc.
This addresses interrupt storms that were noticed after enabling MSI
in drm. I think this is due to a loose interpretation of the PCI 2.3
spec, which states that a function using MSI is prohibitted from using
INTx. It appears that some vendors interpretted that to mean that they
should handle it in hardware, while others felt it was the drivers
responsibility.
This fix will also likely resolve interrupt storm related issues with
devices other than drm.
Reviewed by: jhb@
MFC after: 3 days
memory from int to size_t. Implement a workaround for current ABI not
allowing to properly save size for and report more then 2Gb sized segment
of shared memory.
This makes it possible to use > 2 Gb shared memory segments on 64bit
architectures. Please note the new BUGS section in shmctl(2) and
UPDATING note for limitations of this temporal solution.
Reviewed by: csjp
Tested by: Nikolay Dzham <i levsha org ua>
MFC after: 2 weeks
name i2c-address instead of reg. Change the OFW I2C probe to check both
locations for the address.
Submitted by: Marco Trillo
Reported by: Justin Hibbits
contrib/openbsm (svn merge) and src/sys/{bsm,security/audit} (manual
merge).
OpenBSM history for imported revision below for reference.
MFC after: 1 month
Sponsored by: Apple, Inc.
Obtained from: TrustedBSD Project
OpenBSM 1.1 beta 1
- The filesz parameter in audit_control(5) now accepts suffixes: 'B' for
Bytes, 'K' for Kilobytes, 'M' for Megabytes, and 'G' for Gigabytes.
For legacy support no suffix defaults to bytes.
- Audit trail log expiration support added. It is configured in
audit_control(5) with the expire-after parameter. If there is no
expire-after parameter in audit_control(5), the default, then the audit
trail files are not expired and removed. See audit_control(5) for
more information.
- Change defaults in audit_control: warn at 5% rather than 20% free for audit
partitions, rotate automatically at 2mb, and set the default policy to
cnt,argv rather than cnt so that execve(2) arguments are captured if
AUE_EXECVE events are audited. These may provide more usable defaults for
many users.
- Use au_domain_to_bsm(3) and au_socket_type_to_bsm(3) to convert
au_to_socket_ex(3) arguments to BSM format.
- Fix error encoding AUT_IPC_PERM tokens.
changes since the last imported OpenBSM release:
OpenBSM 1.1 beta 1
- The filesz parameter in audit_control(5) now accepts suffixes: 'B' for
Bytes, 'K' for Kilobytes, 'M' for Megabytes, and 'G' for Gigabytes.
For legacy support no suffix defaults to bytes.
- Audit trail log expiration support added. It is configured in
audit_control(5) with the expire-after parameter. If there is no
expire-after parameter in audit_control(5), the default, then the audit
trail files are not expired and removed. See audit_control(5) for
more information.
- Change defaults in audit_control: warn at 5% rather than 20% free for audit
partitions, rotate automatically at 2mb, and set the default policy to
cnt,argv rather than cnt so that execve(2) arguments are captured if
AUE_EXECVE events are audited. These may provide more usable defaults for
many users.
- Use au_domain_to_bsm(3) and au_socket_type_to_bsm(3) to convert
au_to_socket_ex(3) arguments to BSM format.
- Fix error encoding AUT_IPC_PERM tokens.
Obtained from: TrustedBSD Project
Sponsored by: Apple Inc.
filesystem. This avoids confusion with nullfs and unionfs filesystems
which reference the root of a UFS filesystem as a target.
PR: 116849
Approved by: kib
ready status. Most of controllers managed to issue coommand and set BUSY
bit almost simultaneously, before we will read it, but at least JMicron JMB363
don't. Ignore timeout errors to keep old behavior when error there was
impossible.
For me this fixes timeout errors on the first command after channel attach
or reinit. Boot in my case is not affected, as there is much time passing
between reset and next command giving reset time to complete.
Unlike GCC, LLVM defines __STDC_VERSION__ to 199901L by default. This
means `restrict' keywords in files end up being given to lint, which
results in errors during compilation of usr.bin/xlint.
Other keywords are also expanded to nothing when using lint, so do the
same with restrict.
done in other places. Until we have no support for command queueing we have
no any benefit from FBS, while enabling it only here somehow leads to
"port not ready" errors on Intel 63XXESB2 controller.
Tested by: Larry Rosenman <ler AT lerctr.org>
