decoding "took". Other OS's that I checked do not do this and it breaks
some amdpm(4) devices. Prior to 7.2 we did not honor the error returned
when this failed anyway, so this in effect restores previous behavior.
PR: kern/137668
Tested by: Aurelien Mere aurelien.mere amc-os.com
MFC after: 3 days
the work area was totally unsynchronized which means this driver only
had a chance of working on x86 when no bounce buffers were involved,
which isn't that likely given that support for 64-bit DMA is currently
broken throughout ata(4).
- Add necessary little-endian conversion of accesses to the work area,
making this driver work on big-endian hosts. While at it, use the
alignment-agnostic byte order encoders in order to be on the safe side.
- Clear the reserved member of the SG list entries in order to be on the
safe side. [1]
Submitted by: yongari [1]
Reviewed by: yongari
MFC after: 3 days
30-bit like the reset of the controllers supported by this driver.
Actually ALi M5451 can be setup up to generate 32-bit addresses by
setting the 31st bit via the accompanying ISA bridge, which allows
it to work in sparc64 machines whose IOMMU require at least 32-bit
DMA. Even though other architectures would also benefit from 32-bit
DMA, enabling this bit is limited to sparc64 as bus_dma(9) doesn't
generally guarantee that a low address of BUS_SPACE_MAXADDR_32BIT
results in a buffer in the 32-bit range.
- According to Tatsuo YOKOGAWA's ali(4), the the DMA transfer size of
ALi M5451 is fixed to 64k and in fact using the default size of 4k
- The 4DWAVE DX and NX require the recording buffer to be 8-byte
aligned so adjust the bus_dma_tag_create(9) accordingly.
- Unlike the rest of the controllers supported by this driver, the
ALi M5451 only has 32 hardware channels instead of 64 so limit the
loop in tr_intr() accordingly. [1]
Submitted by: yongari [1]
Reviewed by: yongari (superset of what is committed)
MFC after: 3 days
It seems Clang breaks when checking for SPCLKEY, which is now
0x80000000. Using an unsigned integer fixes this. This is also
consistent with other pieces of kbd/syscons code, because these also use
u_int.
Submitted by: rdivacky
- Mark the link as down, so if watchdog reset fails, link watching
failover software can notice it
- Don't send MXGEFW_CMD_ETHERNET_DOWN if the NIC has been reset, it is
not needed, and will fail on a freshly reset NIC.
- Ensure the transmit routines aren't attempting to PIO write to doorbells
while the NIC is being reset.
- Download the correct f/w, rather than using the EEPROM f/w after reset.
- Export a count of the number of watchdog resets via sysctl
- Zero all f/w stats at reset. This will lead to less confusing
diagnostic output when investigating NIC failures.
MFC after: 3 days
instead of SI_SUB_KLD. Note that we don't believe that there is any
consumers of x86bios that would be triggered in the early stage of boot,
so this is more or less just a safebelt.
Submitted by: swell.k at gmail.com
x86emu to this new module.
This changeset also brings a fix for bugs introduced with the initial
x86emu commit, which prevents the user from using some display mode or
cause instant reboots during mode switch.
Submitted by: paradox <ddkprog yahoo com>
Add a maximum response length for FCP RSPNS IUs.
Clarify some of the FC option words for setting parameters
and try and disable automatic PRLI when in target mode- this
should correct some cases of N-port topologies with 23XX cards
where we put out an illegal PRLI (in target mode only we're
not supposed to put out a PRLI).
Just take keyent_t to use an u_int to store the Unicode codepoints.
Unfortunately the keymap is now too big to be loaded using an ioctl
argument, so change the ioctl to pick a pointer.
This change breaks kbdcontrol ABI. It doesn't break X11, because X11
doesn't do anything with syscons keymaps. It just switches the device
out of K_XLATE.
Obtained from: //depot/user/ed/newcons/...
This code seems to do exactly the same as ttydisc_rint_simple() does
nowadays. Just remove it.
Obtained from: //depot/user/ed/newcons/sys/dev/syscons/syscons.c
- Implement MSI support (MSIX support was already there)
- Use a table to drive MSI/MSIX exceptions
- Pre-calculate the command address instead of wasting cycles doing the
calculation on every i/o.
number of MSIX interrupts that are needed, and don't strictly check for 4.
Enable enough interrupt mask bits so that the controller will generate
interrupts in PERFORMANT mode. This fixes the hang-on-boot issues that
people were seeing with newer controllers.
we at least don't panic.
We don't really support dual role mode (INITIATOR/TARGET) any more. We
should but it's broken and will take a fair amount of effort to fix
and correctly manage both initiator and target roles sharing the port
database. So, for now, disallow it.
For some vague reason, it may be possible that scp->cursor_pos exceeds
scp->ysize * scp->xsize. This means that teken_set_cursor() may get
called with an invalid position. Just ignore the old cursor position in
this case.
Reported by: Paul B. Mahol <onemda gmail com>
MFC after: 1 month
- Improve newer AMD processor support (Family 0Fh Revision F and later).
- Adjust offset if DiodeOffet is set and valid. Note it is experimental
but it seems to give us more realistic temperatures. Newer Linux driver
blindly adds 21C for Family 0Fh desktop processors, however.
- Always populate dev.cpu and dev.amdtemp sysctl trees regardless of probe
order for consistency. Previously, dev.cpu.N.temperature was not populated
if amdtemp was loaded later than ACPI CPU driver and temperatures were not
accessible from dev.amdtemp.N.sensor0 tree for Family 10h/11h processors.
- Read the CPUID from PCI register instead of CPUID instruction to prevent
possible revision mismatches on multi-socket system.
- Change macros and variables to make them closer to AMD documents.
- Fix style(9) nits and improve comments.
Different sub-kinds of PCI buses may have different rules and
thus it is up for the bus backends to do proper input checks.
For example, PCIe allows configuration register numbers < 0x1000,
while for PCI proper the limit is 0x100.
And, in fact, the buses already do the checks.
Reviewed by: jhb
MFC after: 1 week
X-ToDo: add check for negative value to bus backends
X-ToDo: use named constant for maximum PCIe register
"set vesa mode" and higher 16bits of the flag would be the desired mode.
One can now set, for instance, hint.sc.0.flags=0x01680180, which means
that the system should set VESA mode 0x168 upon boot.
Submitted by: paradox <ddkprog yahoo com>, swell k at gmail.com with
some minor changes.
| grep <modname>' can be used instead.
Put a message behind bootverbose as
ichwd0: <Intel ICH6M watchdog timer> on isa0
ichwd0: Intel ICH6M watchdog timer (ICH6 or equivalent)
does not make a lot of sense.
MFC after: 1 week
where we figure out the hostname length under the lock, malloc the buffer
with the lock dropped, then recheck the length under the lock and loop again
if the buffer is now too small.
Tested by: Norbert Koch nkoch demig de
MFC after: 3 days
- Add vesa kernel options for amd64.
- Connect libvgl library and splash kernel modules to amd64 build.
- Connect manual page dpms(4) to amd64 build.
- Remove old vesa/dpms files.
Submitted by: paradox <ddkprog yahoo com> [1], swell k at gmail.com
(with some minor tweaks)
them from the old place. This commit necessary so that the tree would not
enter a broken state.
sys/i386/isa/vesa.c -> dev/fb/vesa.c
sys/i386/include/pc/vesa.h -> dev/fb/vesa.h
sys/i386/isa/dpms.c -> dev/dpms/dpms.c
"COMMAND 0x........ TIMEOUT AFTER .. SECONDS" messages. Any commands
that get truly stuck will still trigger the warning and the hardware
health check, just a little bit later.
# My reading of the docs suggests this can only happen on 10Base5 and
# 10Base2 setups (and maybe only the former), which I can't test
# adequately since I have nothing but 10BaseT, etc here.
requirements. It is busdma task, to manage proper alignment by loading
data to bounce buffers.
PR: kern/127316
Reviewed by: current@
Tested by: Ryan Rogers
Now that pty(4) is a loadable kernel module, I'd better move /dev/ptmx
in there as well. This means that pty(4) now provides almost all
pseudo-terminal compatibility code. This means it's very easy to test
whether applications use the proper library interfaces when allocating
pseudo-terminals (namely posix_openpt and openpty).
sure when this became necessary and might be caused by some missing
code to do auto-configuration of DWDS usage
Noticed by: Felix Feng <unixwind@gmail.com>
Right now libteken processes TF_REVERSE internally and returns the
toggled colors to the console driver. This isn't entirely correct. This
means that the bold flag is always processed by the foreground color,
while reversing should be done after the foreground color has been set
to a brighter version by the bold flag.
This is no problem with the syscons driver, because with VGA it only
supports 16 foreground and 8 background colors. My WIP console driver
reconfigures the graphics hardware to disable the blink functionality
and uses 16 foreground and 16 background colors. This means that this
driver will handle the TF_REVERSE flag a little different from what
syscons does right now.
I initially committed libteken to sys/dev/syscons/teken, but now that
I'm working on a console driver myself, I noticed this was not a good
decision. Move it to sys/teken to make it easier for other drivers to
use a terminal emulator.
Also list teken.c in sys/conf/files, instead of listing it in all the
files.arch files separately.
out of the original commit of i7 support. These are all the counters
on pages A-32 and A-33 of the _Intel(R) 64 and IA32 Architectures
Software Developer's Manual Vol 3B_, June 2009. Almost all
of these counters relate to operations on the L2 cache.
Reviewed by: jkoshy
MFC after: 1 month
alignment requirement could be multiple of 4 bytes but I think
using descriptor size would make intention clearer.
Previously the size of rx descriptor was not power of 2 so it
caused panic in bus_dmamem_alloc(9).
Reported by: Jeff Blank (jb000003 <> mr-happy dot com)
MFC after: 3 days
the previous ap is no longer in range) the device will deliver bmiss
interrupts and trigger the state machine. Also arrange to sync the
beacon timers on the next received beacon frame so that when we don't
roam we re-synchronize with the ap.
Tested by: trasz
MFC after: 1 week
turn ends our usb process. This means the proc pointer becomes invalid and will
panic if a new kthread is added. Count the number of threads and clear the proc
pointer on the last one.
Suggested by: julian
MFC after: 3 days
per platform requirements.
Notes:
- Only used by mge(4) at the moment.
- This is very simplified approach and should be replaced by some long-term
solution for managing the board/platform configuration (among others the
MAC-PHY binding info).
Submitted by: Michal Hajduk
Obtained from: Semihalf
BIOS-enumerated devices:
- Assume a device is a match if the memory and I/O ports match even if the
IRQ or DRQ is wrong or missing. Some BIOSes don't include an IRQ for
the atrtc device for example.
- Add a hack to better match floppy controller devices. Many BIOSes do not
include the starting port of the floppy controller listed in the hints
(0x3f0) in the resources for the device. So far, however, all the BIOS
variations encountered do include the 'port + 2' resource (0x3f2), so
adjust the matching for "fdc" devices to look for 'port + 2'.
Reviewed by: imp
MFC after: 3 days
and remove from its dependency on LRO, my tests have shown
that its always beneficial, even when doing bridging.
Second, fix up a few problems in the statistics code, the
adapter dependencies had gotten lost so some code that should
only run on 82599 was always running, this resulted in bogus
flow control numbers on 82598.
- Use CONSOLE_DRIVER() instead of the deprecated CONS_DRIVER() declaration.
- This means we cannot use cn_checkc anymore, which is supposed to do
the same as cn_getc nowadays. Remove the cn_getc implementation (that
was never being called) and rename cn_checkc to cn_getc.
- Don't run-time patch cn_putc, but add the logic to xc_cnputc().
This means I could do some cleanups to our console code...
Tested by: nobody on hackers@
being polled.
- Remove the need for Giant from the USB HUB driver.
- Leave device unconfigured instead of disabling the USB port
when Huawei Autoinstall disk detection triggers. This should
fix problems that the Huawei device is not detected after
Autoinstall eject is issued.
- Reported by: Nikolay Antsiferov
- Fix memory use after free race for USB character devices.
- Reported by: Lucius Windschuh
- Factor out the enumeration lock into three functions to make the
coming newbus lock conversion more easy.
- usbd_enum_lock
- usbd_enum_unlock
- usbd_enum_is_locked
Submitted by: hps
enable the ones we want. This has been changed to better
match the ADMtek's reference design to avoid setting the
power-down configuration line of the PHY at the same time
it is reset.
Submitted by: John Hood via hps
direction even if the actual device is opened for read and
write. Fix fflags check so that the UFM and URIO drivers work.
Reported by: Krassimir Slavchev
Submitted by: hps
keys are pressed.
- Reported by: Various people
- add sysctl to disable keyboard led control request
- Reported by: Yoshihiro Ota
- Save system CPU usage: Patch to stop keyboard timer when no
keys are pressed.
Submitted by: hps
MFC after: 3 days
Unfortunately, the wrappers that are present in pts(4) don't have the
mechanics to allow pty(4) to be unloaded safely, so I'm forcing this kld
to return EBUSY. This also means we have to enable some extra code in
pts(4) unconditionally.
Proposed by: rwatson
I noticed several drivers in our tree don't actually care about parity
and framing, such as pts(4), snp(4) (and my partially finished console
driver). Instead of duplicating a lot of code, I think we'd better add a
utility function for those drivers to quickly process a buffer of input.
Also change pts(4) and snp(4) to use this function.
It is necessary to make sure cpi->transport is set for xpt_scan_bus() to
work properly.
Submitted by: Bernhard Schmidt (scb+freebsd-current <at> techwires
<dot> net)
Reviewed by: scottl
Approved by: re (kib)
Without this changeset there will be no way to prevent these NICs from
sending ARP, which is harmful in server farms that is configured as
"Direct Server Return" behind a load balancer.
A better fix would remove the whole hack completely but it would be
later than 8.0-RELEASE.
Reviewed by: jfv, yongari
Approved by: re (kib)
- usb_pc_cpu_invalidate() is called between [consecutive] reads from a device,
so a sequence of BUS_DMASYNC_POSTREAD and _PREREAD should be used. Note we
cannot use or'ed shorthand ( _POSTREAD | _PREREAD) for BUS_DMASYNC flags, as
the low level bus dma sync operation is implementation dependent and we
cannot assume the required order of operations to be guaranteed.
- usb_pc_cpu_flush() is called before writing to a device, so
BUS_DMASYNC_PREWRITE should be used.
Submitted by: Grzegorz Bernacki
Reviewed by: HPS, arm@, usb@ ML
Tested by: HPS, Mike Tancsa
Approved by: re (kib)
Obtained from: Semihalf
loop iteration as it can be updated by the card while we
process the RX ring forcing us to process RX descriptors
for which DMA synchronisation operation has not been
performed. This fixes the bug when bge(4) drops packets
under high load.
Discussed with: yongari, marius
Approved by: re (kib)
MFC after: 1 week
value instead of blindly resetting it to 0. However, it seems page
select bits of some 88E1116 PHY is initialized to invalid one such
that restoring page select bits after programming broke MII
register access. The correct solution would be reset page select
bits to 0 in PHY attach stage but it would require more testing.
Since we're in BETA stage such a change would be dangerous so just
back it out.
This change should fix nfe(4) breakage on NVIDIA MCP55.
Reported by: Ryan Rogers < webmaster <> doghouserepair dot com >
Sam Fourman Jr. < sfourman <> gmail dot com >
Tested by: Ryan Rogers < webmaster <> doghouserepair dot com >
Sam Fourman Jr. < sfourman <> gmail dot com >
Approved by: re (kib)
cosmetic change to reduce cruft in the proc table.
Also change the idle wait message to `-` like how taskqueues are.
Reviewed by: julian
Approved by: re (kib)
- Provide lapic_disable_pmc(), lapic_enable_pmc(), and lapic_reenable_pmc()
routines in the local APIC code that the hwpmc(4) driver can use to
manage the local APIC PMC interrupt vector.
- Do not enable the local APIC PMC interrupt vector by default when
HWPMC_HOOKS is enabled. Instead, the hwpmc(4) driver explicitly
enables the interrupt when it is succesfully initialized and disables
the interrupt when it is unloaded. This avoids enabling the interrupt
on unsupported CPUs which may result in spurious NMIs.
Reported by: rnoland
Reviewed by: jkoshy
Approved by: re (kib)
MFC after: 2 weeks
controllers. Controller, array, and drive status can be checked, basic
attributes can be changed, and arrays and spares can be created and deleted.
Controller firmware can also be flashed.
This does not replace MegaCLI, found in ports, as that is officially sanctioned
and supported by LSI and includes vastly more functionality. However, mfiutil
is open source and guaranteed to provide basic functionality, which can be
especially useful if you have a problem and can't get MegaCLI to work.
Approved by: re
Obtained from: Yahoo! Inc.
all pertinent statatistics for the subsystem. These structures are
sometimes "borrowed" by kernel modules that require a place to store
statistics for similar events.
Add KPI accessor functions for statistics structures referenced by kernel
modules so that they no longer encode certain specifics of how the data
structures are named and stored. This change is intended to make it
easier to move to per-CPU network stats following 8.0-RELEASE.
The following modules are affected by this change:
if_bridge
if_cxgb
if_gif
ip_mroute
ipdivert
pf
In practice, most of these statistics consumers should, in fact, maintain
their own statistics data structures rather than borrowing structures
from the base network stack. However, that change is too agressive for
this point in the release cycle.
Reviewed by: bz
Approved by: re (kib)
The newbus lock is responsible for protecting newbus internIal structures,
device states and devclass flags. It is necessary to hold it when all
such datas are accessed. For the other operations, softc locking should
ensure enough protection to avoid races.
Newbus lock is automatically held when virtual operations on the device
and bus are invoked when loading the driver or when the suspend/resume
take place. For other 'spourious' operations trying to access/modify
the newbus topology, newbus lock needs to be automatically acquired and
dropped.
For the moment Giant is also acquired in some key point (modules subsystem)
in order to avoid problems before the 8.0 release as module handlers could
make assumptions about it. This Giant locking should go just after
the release happens.
Please keep in mind that the public interface can be expanded in order
to provide more support, if there are really necessities at some point
and also some bugs could arise as long as the patch needs a bit of
further testing.
Bump __FreeBSD_version in order to reflect the newbus lock introduction.
Reviewed by: ed, hps, jhb, imp, mav, scottl
No answer by: ariff, thompsa, yongari
Tested by: pho,
G. Trematerra <giovanni dot trematerra at gmail dot com>,
Brandon Gooch <jamesbrandongooch at gmail dot com>
Sponsored by: Yahoo! Incorporated
Approved by: re (ksmith)
vnet.h, we now use jails (rather than vimages) as the abstraction
for virtualization management, and what remained was specific to
virtual network stacks. Minor cleanups are done in the process,
and comments updated to reflect these changes.
Reviewed by: bz
Approved by: re (vimage blanket)
firmware loading bugs.
Target mode support has received some serious attention to make it
more usable and stable.
Some backward compatible additions to CAM have been made that make
target mode async events easier to deal with have also been put
into place.
Further refinement and better support for NP-IV (N-port Virtualization)
is now in place.
Code for release prior to RELENG_7 has been stripped away for code clarity.
Sponsored by: Copan Systems
Reviewed by: scottl, ken, jung-uk kim
Approved by: re
USB core:
- add support for defragging of written device data.
- improve handling of alternate settings in device side mode.
- correct return value from usbd_get_no_alts() function.
- reported by: HPS
- P4 ID: 166156, 166168
- report USB device release information to devd and pnpinfo.
- reported by: MIHIRA Sanpei Yoshiro
- P4 ID: 166221
Submitted by: hps
Approved by: re
See PR description for more info. Patch is
implemented differently than suggested, but
having the same result.
PR: usb/137188
Submitted by: hps
Approved by: re
- add support for defragging of written device data.
- improve handling of alternate settings in device side mode.
- correct return value from usbd_get_no_alts() function.
- reported by: HPS
- P4 ID: 166156, 166168
- report USB device release information to devd and pnpinfo.
- reported by: MIHIRA Sanpei Yoshiro
- P4 ID: 166221
Submitted by: hps
Approved by: re
- Add minimum polling support to drive UMASS
and UKBD in case of panic.
- Add extra check to ukbd probe to fix problem about
mouse devices attaching like keyboards.
- P4 ID: 166148
Submitted by: hps
Approved by: re
- add support for setting the UMS polling rate through -F option
passed to moused.
- requested by Alexander Best
- P4 ID: 166075
PR: usb/125264
Submitted by: hps
Approved by: re
requesting IDENTIFY from slave device first. This order is important
for proper cable type detection by master device.
PR: kern/136438
Approved by: re (kib)
- When a vlan event occurs a check was not made that
the event was actually for the interface, thus resulting
in a panic. All three drivers have this vulnerability. Add
a check for this condition.
- Secondly, there was a duplicate buf_ring free in the em
driver resulting in a panic on unload. Remove.
Approved by: re
part that is made up of 8K banks rather than 4K, if these
systems are using bank 1 then the last change in this code
breaks the bank read, resulting in an invalid checksum of
the eeprom during driver load. This change fixes this.
Approved by: re
if input-device is unavailable. The Xserve G5 defaults to using
screen/keyboard for output-device/input-device even if these are not
installed, and then falls back to serial ports at boot time.
Reviewed by: marcel
Hardware from: grehan
Approved by: re (kib)
loader, because it uses a reserved suffix (_type). Fix
this by removing the "_" and renaming the tunable to
hw.mxge.rss_hashtype. The old (rss_hash_type) tunable is
still fetched, in case people load the driver via scripts.
When both are present in the kernel environment,
the new value (hw.mxge.rss_hashtype) overrides the old
value.
Approved by: re (kib)
actually specify valid bases that should be treated just as normal.
The PCI specifications have no indication that 0 would be a magic value
indicating a disabled BAR as commonly used on at least amd64 and i386
but not sparc64. It's unclear what to do in pci_delete_resource()
instead of writing 0 to a BAR though as there's no (other) way do
disable individual BARs so its decoding is left enabled in case of
__PCI_BAR_ZERO_VALID for now.
Approved by: re (kib), jhb
MFC after: 1 week
Driver supports Serial ATA and ATAPI devices, Port Multipliers
(including FIS-based switching), hardware command queues (31 command
per port) and Native Command Queuing. This is probably the second on
popularity, after AHCI, type of SATA2 controllers, that benefits from
using CAM, because of hardware command queuing support.
Approved by: re (kib)
nagged again via PR. Thank Paul for his persistence and contributions.
PR: 136895
Submitted by: Paul B. Mahol <onemda@gmail.com>
Reviewed by: sam (timeout, 10 days), weongyo (timeout, 10 days), me
Approved by: re (Kostik Belousov <kostikbel@gmail.com>)
(DPCPU), as suggested by Peter Wemm, and implement a new per-virtual
network stack memory allocator. Modify vnet to use the allocator
instead of monolithic global container structures (vinet, ...). This
change solves many binary compatibility problems associated with
VIMAGE, and restores ELF symbols for virtualized global variables.
Each virtualized global variable exists as a "reference copy", and also
once per virtual network stack. Virtualized global variables are
tagged at compile-time, placing the in a special linker set, which is
loaded into a contiguous region of kernel memory. Virtualized global
variables in the base kernel are linked as normal, but those in modules
are copied and relocated to a reserved portion of the kernel's vnet
region with the help of a the kernel linker.
Virtualized global variables exist in per-vnet memory set up when the
network stack instance is created, and are initialized statically from
the reference copy. Run-time access occurs via an accessor macro, which
converts from the current vnet and requested symbol to a per-vnet
address. When "options VIMAGE" is not compiled into the kernel, normal
global ELF symbols will be used instead and indirection is avoided.
This change restores static initialization for network stack global
variables, restores support for non-global symbols and types, eliminates
the need for many subsystem constructors, eliminates large per-subsystem
structures that caused many binary compatibility issues both for
monitoring applications (netstat) and kernel modules, removes the
per-function INIT_VNET_*() macros throughout the stack, eliminates the
need for vnet_symmap ksym(2) munging, and eliminates duplicate
definitions of virtualized globals under VIMAGE_GLOBALS.
Bump __FreeBSD_version and update UPDATING.
Portions submitted by: bz
Reviewed by: bz, zec
Discussed with: gnn, jamie, jeff, jhb, julian, sam
Suggested by: peter
Approved by: re (kensmith)
This dramatically pushing 99.9% interpolations and quantizations
error _below_ -180dB on 32bit dynamic range, resulting extremely
high quality conversion.
- Use BSPLINE interpolator for filter oversampling factor greater or
equal than 64 (log2 6).
Approved by: re (kib)
check missed this because cxgb's TOM is currently commented out of the build
system.
Submitted by: Navdeep Parhar <np at FreeBSD dot org>
Approved by: re (kensmith), kensmith (mentor temporarily unavailable)
the TCP syncache. This returns struct tcpopt to being private within the TCP
implementation, thus allowing it to be modified without ABI concerns.
The patch breaks the ABI. Bump __FreeBSD_version to 800103 accordingly. The cxgb
driver is the only TOE consumer affected by this change, and needs to be
recompiled along with the kernel.
Suggested by: rwatson
Reviewed by: rwatson, kmacy
Approved by: re (kensmith), kensmith (mentor temporarily unavailable)
USB CORE: busdma improvement
For single segment allocations the boundary field
of the BUSDMA tag should be zero. Currently all
single segment allocations are less than or equal
to 4096 bytes, so the limit does not kick in. If
any single segment USB allocations would be greater
than 4K, then it would be a problem.
Approved by: re (kensmith)
Obtained from: HPS
/boot/kernel/hptrr.ko
/etc/mail/*.cf
/lib/libcrypto.so.5
/usr/bin/ntpq
/usr/sbin/amd
/usr/sbin/iasl
/usr/sbin/ntpd
/usr/sbin/ntpdate
/usr/sbin/ntpdc
There does not appear to be any purpose to having these timestamps, and
they have the irritating consequence that the aforementioned files will
be different every time they are rebuilt.
After this commit, the only remaining build timestamps are in the kernel,
the boot loaders, /usr/include/osreldate.h (the year in the copyright
notice), and lib*.a (the timestamps on all of the included .o files).
Reviewed by: scottl (hptrr), gshapiro (sendmail), simon (openssl),
roberto (ntp), jkim (acpica)
Approved by: re (kib)
net80211 wireless stack. This work is based on the March 2009 D3.0 draft
standard. This standard is expected to become final next year.
This includes two main net80211 modules, ieee80211_mesh.c
which deals with peer link management, link metric calculation,
routing table control and mesh configuration and ieee80211_hwmp.c
which deals with the actually routing process on the mesh network.
HWMP is the mandatory routing protocol on by the mesh standard, but
others, such as RA-OLSR, can be implemented.
Authentication and encryption are not implemented.
There are several scripts under tools/tools/net80211/scripts that can be
used to test different mesh network topologies and they also teach you
how to setup a mesh vap (for the impatient: ifconfig wlan0 create
wlandev ... wlanmode mesh).
A new build option is available: IEEE80211_SUPPORT_MESH and it's enabled
by default on GENERIC kernels for i386, amd64, sparc64 and pc98.
Drivers that support mesh networks right now are: ath, ral and mwl.
More information at: http://wiki.freebsd.org/WifiMesh
Please note that this work is experimental. Also, please note that
bridging a mesh vap with another network interface is not yet supported.
Many thanks to the FreeBSD Foundation for sponsoring this project and to
Sam Leffler for his support.
Also, I would like to thank Gateworks Corporation for sending me a
Cambria board which was used during the development of this project.
Reviewed by: sam
Approved by: re (kensmith)
Obtained from: projects/mesh11s
The default (64K) is too pessimistic for "new comm" hardware.
Also, this is bad because multiple controllers get limited by
the global tunable.
Reviewed by: scottl
Approved by: re (kensmith)
modularize it so that new transports can be created.
Add a transport for SATA
Add a periph+protocol layer for ATA
Add a driver for AHCI-compliant hardware.
Add a maxio field to CAM so that drivers can advertise their max
I/O capability. Modify various drivers so that they are insulated
from the value of MAXPHYS.
The new ATA/SATA code supports AHCI-compliant hardware, and will override
the classic ATA driver if it is loaded as a module at boot time or compiled
into the kernel. The stack now support NCQ (tagged queueing) for increased
performance on modern SATA drives. It also supports port multipliers.
ATA drives are accessed via 'ada' device nodes. ATAPI drives are
accessed via 'cd' device nodes. They can all be enumerated and manipulated
via camcontrol, just like SCSI drives. SCSI commands are not translated to
their ATA equivalents; ATA native commands are used throughout the entire
stack, including camcontrol. See the camcontrol manpage for further
details. Testing this code may require that you update your fstab, and
possibly modify your BIOS to enable AHCI functionality, if available.
This code is very experimental at the moment. The userland ABI/API has
changed, so applications will need to be recompiled. It may change
further in the near future. The 'ada' device name may also change as
more infrastructure is completed in this project. The goal is to
eventually put all CAM busses and devices until newbus, allowing for
interesting topology and management options.
Few functional changes will be seen with existing SCSI/SAS/FC drivers,
though the userland ABI has still changed. In the future, transports
specific modules for SAS and FC may appear in order to better support
the topologies and capabilities of these technologies.
The modularization of CAM and the addition of the ATA/SATA modules is
meant to break CAM out of the mold of being specific to SCSI, letting it
grow to be a framework for arbitrary transports and protocols. It also
allows drivers to be written to support discrete hardware without
jeopardizing the stability of non-related hardware. While only an AHCI
driver is provided now, a Silicon Image driver is also in the works.
Drivers for ICH1-4, ICH5-6, PIIX, classic IDE, and any other hardware
is possible and encouraged. Help with new transports is also encouraged.
Submitted by: scottl, mav
Approved by: re
MAXPHYS. Current ataahci driver memory allocation scheme includes only
64 items in DMA S/G table, and so not guarantied to support transactions
with more then 252K data.
Approved by: re (kensmith)
MFC after: 2 weeks
is invalid because the ioctl happens without prior open. The ioctl
got introduced to provide backward compatibility for extended
partitions, but it ended up not being used because it didn't work
as expected. Since there are no consumers of the ioctl and the
implementation is broken, the best fix is to remove the code
entirely.
Spotted by: phk
Approved by: re (kensmith)
This cause dramatic effect in overall precision and conversion quality
by pushing down most aliasing artifacts around -180 dB.
Spectrogram analysis/comparison:
http://people.freebsd.org/~ariff/z_comparison/z_28vs30/
- Guard against possible 64bit overflow during accumulation process by
slightly normalize and saturate sample and coefficient multiplication,
possible during extreme 32bit downsampling (eg. 380KHz -> 8KHz) with
custom preset that require more than ~7000 taps filter (which is
overkill).
- Add knobs through FEEDER_RATE_PRESETS to set dynamic range of filter
coefficients/accumulator and prefered polynomial interpolator:
COEFFICIENT_BIT:X
(where 1 <= X <= 30, default: 30)
ACCUMULATOR_BIT:X
(where 32 <= X <=64, default: 58)
INTERPOLATOR:I
(where I = ZOH, LINEAR, QUADRATIC, HERMITE, BSPLINE,
OPT32X, OPT16X, OPT8X, OPT4X, OPT2X)
Approved by: re (kib)
o add a new facility for components to register send+recv handlers
o ieee80211_send_action and ieee80211_recv_action now use the registered
handlers to dispatch operations
o rev ieee80211_send_action api to enable passing arbitrary data
o rev ieee80211_recv_action api to pass the 802.11 frame header as it may
be difficult to locate
o update existing IEEE80211_ACTION_CAT_BA and IEEE80211_ACTION_CAT_HT handling
o update mwl for api rev
Reviewed by: rpaulo
Approved by: re (kensmith)
- sysctl dev.acpi_hp.0.verbose to toggle debug output
- A modification so this can deal with different array lengths
when reading the CMI BIOS - now it works ok on HP Compaq nx7300
as well.
- Change behaviour to query only max_instance-1 CMI BIOS instances,
because all HPs seen so far are broken in that respect
(or there is a fundamental misunderstanding on my side, possible
as well). This way a disturbing ACPI Error Field exceeds Buffer
message is avoided.
- New bit to set on dev.acpi_hp.0.cmi_detail (0x8) to
also query the highest guid instance of CMI bios
acpi_hp.4:
- Document dev.acpi_hp.0.verbose sysctl in man page
- Document new bit for dev.acpi_hp.0.cmi_detail
- Add a section to manpage about hardware that has been reported
to work ok
Submitted by: Michael Gmelin <freebsdusb at bindone.de>
Approved by: re (kib)
MFC after: 2 weeks
via cpuctl(4) driver. Two new CPUCTL_MSRSBIT and CPUCTL_MSRCBIT ioctl(2)
calls treat the data field of the argument struct passed as a mask
and set/clear bits of the MSR register according to the mask value.
- Allow user to perform atomic bitwise AND and OR operaions on MSR registers
via cpucontrol(8) utility. Two new operations ("&=" and "|=") have been
added. The first one applies bitwise AND operaion between the current
contents of the MSR register and the mask, and the second performs bitwise
OR. The argument can be optionally prefixed with "~" inversion operator.
This allows one to mimic the "clear bit" behavior by using the command
like this:
cpucontrol -m 0x10&=~0x02 # clear the second bit of TSC MSR
Inversion operator support in all modes (assignment, OR, AND).
Approved by: re (kib)
MFC after: 1 month
- Document different semantics for ACPI_WMI_PROVIDES_GUID_STRING_METHOD
acpi_wmi.c:
- Modify acpi_wmi_provides_guid_string_method to return absolut number of
instances known for the given GUID.
acpi_hp.c:
- sysctl dev.acpi_hp.0.verbose to toggle debug output
- A modification so this can deal with different array lengths
when reading the CMI BIOS - now it works ok on HP Compaq nx7300
as well.
- Change behaviour to query only max_instance-1 CMI BIOS instances,
because all HPs seen so far are broken in that respect
(or there is a fundamental misunderstanding on my side, possible
as well). This way a disturbing ACPI Error Field exceeds Buffer
message is avoided.
- New bit to set on dev.acpi_hp.0.cmi_detail (0x8) to
also query the highest guid instance of CMI bios
acpi_hp.4:
- Document dev.acpi_hp.0.verbose sysctl in man page
- Document new bit for dev.acpi_hp.0.cmi_detail
- Add a section to manpage about hardware that has been reported
to work ok
Submitted by: Michael Gmelin, freebsdusb at bindone.de
Approved by: re (kib)
MFC after: 2 weeks
