Socket 8 to 370 converters. When (1) CPU_PPRO2CELERON option is
defined, (2) Intel CPU is found and (3) CPU ID is 0x66?, L2 cache is
enabled through MSR 0x11e. The L2 cache latency value can be
specified by CPU_L2_LATENCY option. Default value of L2 cache latency
is 5.
These options are useful if you use Socket 8 to Socket 370 converter
(e.g. Power Leap's PL-Pro/II.) Most PentiumPro BIOSs don't enable L2
cache of Mendocino Celeron CPUs because they don't know Celeron CPUs.
These options are needles if you use a Coppermine (FCPGA) Celeron or
PentiumIII, becuase the L2 cache enable bit is hard wired and L2 cache
is always enabled.
- Add support for using the PCI BIOS functions for configuration space
accesses, and make this the default.
- Make PNPBIOS the default (obsoletes the PNPBIOS config option).
- Add two new boot-time tunables to disable each of the above.
it's options COMPAT_OLDISA and COMPAT_OLDPCI. This is meant to be a
fairly strong incentive to update the older drivers to newbus, but doesn't
(quite) leave anybody hanging with no hardware support. I was talking with
a few folks and I was encouraged to simply break or disable the shims but
that was a bit too drastic for my liking.
Note1: the correct interrupt level is invoked correctly for each driver.
For this purpose, drivers request the bus before being able to
call BUS_SETUP_INTR and BUS_TEARDOWN_INTR call is forced by the ppbus
core when drivers release it. Thus, when BUS_SETUP_INTR is called
at ppbus driver level, ppbus checks that the caller owns the
bus and stores the interrupt handler cookie (in order to unregister
it later).
Printing is impossible while plip link is up is still TRUE.
vpo (ZIP driver) and lpt are make in such a way that
using the ZIP and printing concurrently is permitted is also TRUE.
Note2: specific chipset detection is not done by default. PPC_PROBE_CHIPSET
is now needed to force chipset detection. If set, the flags 0x40
still avoid detection at boot.
Port of the pcf(4) driver to the newbus system (was previously directly
connected to the rootbus and attached by a bogus pcf_isa_probe function).
COMPAT_LINUX are there. It shouldn't be and isn't used after config
time, except to complicate the svr4 module makefile.
Moved options for emulators to a separate section.
* GC unused options
* Move options that exist on all architectures to conf/options
* Add missing options to LINT
* Sort undocumented options list in LINT
Reviewed by: green
that goes to opt_dontuse.h is so an opt_*.h file doesn't get created even
though an option may be used for bringing stuff in via files[.*].
Pointed out by: bde
- Split syscons source code into manageable chunks and reorganize
some of complicated functions.
- Many static variables are moved to the softc structure.
- Added a new key function, PREV. When this key is pressed, the vty
immediately before the current vty will become foreground. Analogue
to PREV, which is usually assigned to the PrntScrn key.
PR: kern/10113
Submitted by: Christian Weisgerber <naddy@mips.rhein-neckar.de>
- Modified the kernel console input function sccngetc() so that it
handles function keys properly.
- Reorganized the screen update routine.
- VT switching code is reorganized. It now should be slightly more
robust than before.
- Added the DEVICE_RESUME function so that syscons no longer hooks the
APM resume event directly.
- New kernel configuration options: SC_NO_CUTPASTE, SC_NO_FONT_LOADING,
SC_NO_HISTORY and SC_NO_SYSMOUSE.
Various parts of syscons can be omitted so that the kernel size is
reduced.
SC_PIXEL_MODE
Made the VESA 800x600 mode an option, rather than a standard part of
syscons.
SC_DISABLE_DDBKEY
Disables the `debug' key combination.
SC_ALT_MOUSE_IMAGE
Inverse the character cell at the mouse cursor position in the text
console, rather than drawing an arrow on the screen.
Submitted by: Nick Hibma (n_hibma@FreeBSD.ORG)
SC_DFLT_FONT
makeoptions "SC_DFLT_FONT=_font_name_"
Include the named font as the default font of syscons. 16-line,
14-line and 8-line font data will be compiled in. This option replaces
the existing STD8X16FONT option, which loads 16-line font data only.
- The VGA driver is split into /sys/dev/fb/vga.c and /sys/isa/vga_isa.c.
- The video driver provides a set of ioctl commands to manipulate the
frame buffer.
- New kernel configuration option: VGA_WIDTH90
Enables 90 column modes: 90x25, 90x30, 90x43, 90x50, 90x60. These
modes are mot always supported by the video card.
PR: i386/7510
Submitted by: kbyanc@freedomnet.com and alexv@sui.gda.itesm.mx.
- The header file machine/console.h is reorganized; its contents is now
split into sys/fbio.h, sys/kbio.h (a new file) and sys/consio.h
(another new file). machine/console.h is still maintained for
compatibility reasons.
- Kernel console selection/installation routines are fixed and
slightly rebumped so that it should now be possible to switch between
the interanl kernel console (sc or vt) and a remote kernel console
(sio) again, as it was in 2.x, 3.0 and 3.1.
- Screen savers and splash screen decoders
Because of the header file reorganization described above, screen
savers and splash screen decoders are slightly modified. After this
update, /sys/modules/syscons/saver.h is no longer necessary and is
removed.
perform a cleanup/unifdef sweep over it to tidy things up. The atapi
code is permanently attached to the wd driver and is always probed.
I will add an extra option bit in the flags to disable an atapi probe on
either the master or slave if needed, if people want this.
Remember, this driver is destined to die some time. It's possible that
it will loose all atapi support down the track and only be used for
dumb non-ATA disks and all ata/atapi devices will be handled by the new
ata system.
ATAPI, ATAPI_STATIC and CMD640 are no longer options, all are implicit.
Previously discussed with: sos
- Refined internal interface in keyboard drivers so that:
1. the side effect of device probe is kept minimal,
2. polling mode function is added,
3. and new ioctl and configuration options are added (see below).
- Added new ioctl: KDSETREPEAT
Set keyboard typematic rate. There has existed an ioctl command,
KDSETRAD, for the same purpose. However, KDSETRAD is dependent on
the AT keyboard. KDSETREPEAT provides more generic interface.
KDSETRAD will still be supported in the atkbd driver.
- Added new configuration options:
ATKBD_DFLT_KEYMAP
Specify a keymap to be used as the default, built-in keymap.
(There has been undocumented options, DKKEYMAP, UKKEYMAP, GRKEYMAP,
SWKEYMAP, RUKEYMAP, ESKEYMAP, and ISKEYMAP to set the default keymap.
These options are now gone for good. The new option is more general.)
KBD_DISABLE_KEYMAP_LOADING
Don't allow the user to change the keymap.
Move the Olicom token ring driver to the officially sanctionned location of
/sys/contrib. Also fix some brokenness in the generic token ring support.
Be warned that if_dl.h has been changed and SOME programs might
like recompilation.
keyboard and video card drivers.
Because of the changes, you are required to update your kernel
configuration file now!
The files in sys/dev/syscons are still i386-specific (but less so than
before), and won't compile for alpha and PC98 yet.
syscons still directly accesses the video card registers here and
there; this will be rectified in the later stages.
CPU_WT_ALLOC does not work correctly for K6-2s of model 8+ and
probably K6-3s (when they appear on the market soon). In addition,
print_AMD_info() incorrectly printfs write allocation's size. I've
fixed them, so they now Do The Right Thing, and added a
"NO_MEMORY_HOLE" option to easily allow 15-16mb range handling for us
K6 and K6-2 users.
Submitted by: Brian Feldman <green@unixhelp.org>
ISDN4BSD is the work of our brand-new comitter: Hellmuth Michaelis,
who has done a tremendous amount of work to bring us this far.
There are still some outstanding issues and files to bring into
the tree, and for now it will be needed to pick up all the extra
docs from the isdn4bsd release.
It is probably also a very good idea to subscribe to the isdn@freebsd.org
mailing list before you try this out.
These files correspond to release "beta Version 0.70.00 / December
1998" from Hellmuth.
floppy is used on the toshiba Libretto line of subnotebook computers.
It differs from a normal floppy in that you must use PIO rather than
DMA to transfer the data.
To enable this, you must add options "FDC_YE" to your kernel. I don't
have a machine that has a floppy and a pcmcia slot to test to make
sure that this doesn't impact normal floppy units, so I've left this as
an option.
I have ported this to -current and made an attempt to ensure that the
indentation conforms to style(9), aka the bruce filter.
Reviewed by: nate, markm
Submitted by: David Horwitt (dhorwitt@ucsd.edu)
