is only used by the icu support modules and by a few drivers that know
too much about the icu (most only use it to convert `n' to `IRQn'). isa.h
is only used by ioconf.c and by a few drivers that know too much about
isa addresses (a few have to, because config is deficient).
This will do as a stop-gap until I figure out a more fault-tolerant
way of having deferred closes against the control connection work
without blocking.
with multiple entries as follows:
start address, end address, resident pages in range, private pages
in range, RW/RO, COW or not, (vnode/device/swap/default).
hacked up by me to remove the IPv6 stuff (fow now). I renamed
it `keyadmin' since `key' was already taken by the S/Key calculator.
Its purpose is to act as a command-driven interface to the `PF_KEY'
socket domain, analogously to thefunction of route(8) in the
`PF_ROUTE' domain. This program is believed to be exportable, since
it does no actual cryptography itself.
compiler warnings which occur if you don't have 'options DEVFS' in
your kernel config file:
../../kern/kern_descrip.c: In function `fildesc_drvinit':
../../kern/kern_descrip.c:1103: warning: unused variable `fd'
../../kern/kern_descrip.c: At top level:
../../kern/kern_descrip.c:1095: warning: `devfs_token_stdin' defined but not use
d
../../kern/kern_descrip.c:1096: warning: `devfs_token_stdout' defined but not us
ed
../../kern/kern_descrip.c:1097: warning: `devfs_token_stderr' defined but not us
ed
../../kern/kern_descrip.c:1098: warning: `devfs_token_fildesc' defined but not u
sed
to match (pc98/random_machdep.c probably requires a similar change). This
is a problem area for the PC98 merge - all PC98 ifdefs in <machine/*.h> are
kludges to work around incorrect layering.
from jmz was a hopeless kludge (sorry Jean-Marc :) and handled the problem
in the wrong way. ftpRestart() has now gone away and ftpGet() has grown a
new parameter.
disklabel(8) to the kernel (dsopen()). Drivers should initialize the
hardware values (rpm, interleave, skews). Drivers currently don't do
this, but it usually doesn't matter since rotational position stuff is
normally disabled.
Original version by John Hay.
Simplified timestamp code by reading the time exactly when necessary.
This may slow down the interrupt handler with extra calls to microtime(),
but only in bad configurations - the input fifo should normally be
disabled if timestamps on input are being used, since otherwise the
timestamp won't be precisely associated with any particular input event.
The interrupt handler remains slowed down by one test and branch for
each input (and now DCD change) event - avoiding this is not practical
yet.
The simplifications also fixed:
- timestamps for input sometimes being clobbered by output and modem
status interrupts.
- valid timestamps not being available unless the port is configured with
vector siointrts. siointrts no longer exists.
- compiler warnings about siointr* in some configurations.
Simplified timestamp and probe code by depending on recent changes in
microtime() and DELAY() to preserve the interrupt enable flag.
enable flag instead of enable_intr() to restore it to its usual state.
getit() is only called from DELAY() so there is no point in optimising
its speed (this wasn't so clear when it was extern), and using
enable_intr() made it inconvenient to call DELAY() from probes that need
to run with interrupts disabled.
instead of sti to it restore to its usual state. pushfl/popfl is
actually faster in protected mode on Pentiums (4+3 cycles instead of 9),
and using sti made it extremely inconvenient to call microtime() from
fast interrupt handlers. pushfl/popfl is a couple of cycles slower than
sti on 486's and a couple more cycles slower on 386's, but the relative
cost of using it is not large since microtime() has to use slow i/o
instructions on the old cpus.
1) Make it much less likely to miss a wakeup in vm_page_free_wakeup
2) Create a new entry point into pmap: pmap_ts_referenced, eliminates
the need to scan the pv lists twice in many cases. Perhaps there
is alot more to do here to work on minimizing pv list manipulation
3) Minor improvements to vm_pageout including the use of pmap_ts_ref.
4) Major changes and code improvement to pmap. This code has had
several serious bugs in page table page manipulation. In order
to simplify the problem, and hopefully solve it for once and all,
page table pages are no longer "managed" with the pv list stuff.
Page table pages are only (mapped and held/wired) or
(free and unused) now. Page table pages are never inactive,
active or cached. These changes have probably fixed the
hold count problems, but if they haven't, then the code is
simpler anyway for future bugfixing.
5) The pmap code has been sorely in need of re-organization, and I
have taken a first (of probably many) steps. Please tell me
if you have any ideas.
