When not defining header split do not allocate mbufs,
this can be a BIG savings in the mbuf memory pool.
Also keep seperate dma maps for the header and
payload pieces when doing header split. The basis
of this code was a patch done a while ago by
yongari, thank you :)
A number of white space changes.
MFC: in a few days
free(9) and it can cause kernel panic when there are multiple graphics
controllers in the system.
Tested by: Brandon Gooch (jamesbrandongooch at gmail dot com)
MFC after: 3 days
firmware in order to take over control of the SMU. Without doing this,
the firmware background process doing fan control will run amok as we
take over the system and crash the management chip.
This is limited to these two machines because our kernel is heavily
dependent on firmware accesses, and so quiescing firmware can cause
nasty problems.
Powermac G5 systems. MSI and several other things are not presently
supported.
The U3/U4 internal device support portions of this change were contributed
by Andreas Tobler.
MFC after: 1 week
so ni_txrate returned 0 which is a invalid result.
- The fourth argument of ieee80211_ratectl_tx_complete() could be not
NULL.
Reported by: Gustau P?rez <gperez at entel.upc.edu>
Tested by: Gustau P?rez <gperez at entel.upc.edu>,
Ian FREISLICH <ianf at clue.co.za>
MFC after: 3 days
- add a moderation value to the Link vector
- allow disabling HW RSC on the 82599 if LRO
is not enabled.
- correct error in the stats code
- change optic type on the 82598 DA device
Thanks to Andrew Boyer for the changes.
RFA. Also drop frames that have either CRC error or alignment
error. Normally bad frames are not received at all. But controllers
running in promiscuous mode will receive bad frames. 82557 will
also receive bad frames to receive VLAN oversized frames.
While I'm here mark RNR condition if driver happen to see RNR in
RFA status and restart RU to receive frames again. Because driver
checks all received frames in RX loop, RNR condition could be set
in the middle of RX processing. Just relying on RNR interrupt was
not enough.
This change fixes "Memory modified after free" issue when fxp(4)
is running as a member of if_bridge(4).
Tested by: Larry Baird <lab <> gta dot com>
MFC after: 5 days
microframe slot was not in the smask. The problem was that the EHCI driver was
then thinking that the transfer was immediately complete in some cases. Which
could lead to freeze-like situations, which can be recovered by unplugging the
USB device.
Reported by: Richard Kolkovich
Submitted by: Hans Petter Selasky
USB enumeration lock is locked, then the USB stack fails to resume the device
because locking the USB enumeration lock is part of the resume procedure. To
solve this issue a new lock is introduced which only protects the suspend and
resume callbacks, which can be dropped inside the usbd_do_request_flags()
function, to allow suspend and resume during so-called enumeration operations.
Submitted by: Hans Petter Selasky
hardware tag insertion/stripping. Remove conditional code that
disables these hardware features on SiS190. Also nuke RX fixup code
which is no more required on strict-alignment architectures because
SiS190 supports RX 10 bytes padding.
Now all hardware features except jumbo frame and WOL are supported.
Thanks to Masa Murayama who confirmed SiS190 also has the same
hardware features of SiS191.
I guess the only difference between SiS191 and SiS190 would be
jumbo frame support. It will be implemented in near future.
fragmentation of mbuf chain to 32 from 16 because TSO can send 64KB
sized packet which in turn requires long list of mbuf chain. Due to
lack of documentation, I'm not sure whether driver have to pull up
ethernet/IP/TCP header with options to make controller work but
driver have to parse TCP header to update pseudo TCP checksum
anyway. The controller expects pseudo TCP checksum computed by
upper stack and the checksum should follow the MS NDIS
specification to make TSO work.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
fxp(4) already used to extract most hardware MAC statistics but it
didn't show them. With this change, all MAC statistics counters
are exported. Because there are a couple of new counters for 82558
and 82559, enable extended MAC statistics functionality to get
these counters. Accoring to public data sheet, 82559 MAC statistics
return 24 DWORD counters(3 counters are unknown at this moment) so
increase MAC counter structure to meet the MAC statistics block size.
The completion of MAC counter dump is now checked against
FXP_STATS_DR_COMPLETE status code which is appended at the end of
status block. Previously fxp(4) ignored the status of the
FXP_SCB_COMMAND_CU_DUMPRESET command. fxp(4) does not wait for the
completion of pending command before issuing
FXP_SCB_COMMAND_CU_DUMPRESET. Instead it skips the command and try
it next time. This scheme may show better performance but there is
chance to loose updated counters after stopping controller. So make
sure to update MAC statistics in fxp_stop().
While I'm here move sysctl node creation to fxp_sysctl_node().
Tested by: Larry Baird < lab <> gta dot com >
table. The default size of the configuration table was 22 bytes. To
use extended feature of 82550/82551 the configuration table size
was expanded to 32 bytes. The added configuration for 82550/82551
specifies VLAN hardware tagging and IPSec configuration as well as
TCO.
To make configuration easier fxp(4) used a configuration template
and the template was copied to configuration table. After that,
some parameters of the configuration table was changed depending on
controller type and operation mode. However the size of template
was 22 bytes so some configuration parameters were not properly
initialized on 82550/82551.
Fix this by increasing the template size. For 82557, 82558 and
82559 the size of the configuration is still 22 bytes.
unicast and the other for multicast. To receive multicast frames
that host didn't join in promiscuous mode, driver have to set
promiscuous mode for multicast frames as well.
The Open Source Software Developer Manual for i8255x was not clear
how to handle promiscuous mode.
PR: kern/145905
MFC after: 5 days
from passive to active scans. Basicly disable it by increasing the
amount packets to be received to an amount which can't be reached
during dwell times.
Approved by: rpaulo (mentor)
MFC after: 3 days
L2/3/4 headers and can drop or steer packets as instructed. Filtering
based on src ip, dst ip, src port, dst port, 802.1q, udp/tcp, and mac
addr is possible. Add support in cxgbtool to program these filters.
Some simple examples:
Drop all tcp/80 traffic coming from the subnet specified.
# cxgbtool cxgb2 filter 0 sip 192.168.1.0/24 dport 80 type tcp action drop
Steer all incoming UDP traffic to qset 0.
# cxgbtool cxgb2 filter 1 type udp queue 0 action pass
Steer all tcp traffic from 192.168.1.1 to qset 1.
# cxgbtool cxgb2 filter 2 sip 192.168.1.1 type tcp queue 1 action pass
Drop fragments.
# cxgbtool cxgb2 filter 3 type frag action drop
List all filters.
# cxgbtool cxgb2 filter list
index SIP DIP sport dport VLAN PRI P/MAC type Q
0 192.168.1.0/24 0.0.0.0 * 80 0 0/1 */* tcp -
1 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* udp 0
2 192.168.1.1/32 0.0.0.0 * * 0 0/1 */* tcp 1
3 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* frag -
16367 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* * *
MFC after: 2 weeks
