This seems to indicate whether to program the NIC for fractional 5ghz
mode (ie, 5mhz spaced channels, rather than 10 or 20mhz spacing) or not.
The default (0) seems to mean "only program fractional mode if needed".
A different value (eg 1) seems to always enable fractional 5ghz mode
regardless of the frequency.
Obtained from: Atheros
Approved by: re (kib)
Calibration/PCI data that's written to flash (rather than EEPROM attached
to the NIC) is typically already in host-endian. The existing checks
end up swapping 16 bit words incorrectly - the correct solution would be
to read the magic value and determine the EEPROM endianness from that.
(This is what Linux does.)
This doesn't completely enable embedded use of the AR9285/AR9287 -
notably, the EEPROM read methods need to be made generic and available
to all EEPROM drivers. I'll worry about that later.
Approved by: re (kib)
* I messed up the order of parameter true/false; oops!
* AR_PHY_RADAR_1 was being written at the wrong place, and was writing
potential garbage to the hardware.
Approved by: re (kib)
memtesting, which can easily save seconds to minutes of boot time.
The tunable name is kept general to allow reusing the code in
alternate frameworks.
Requested by: many
Discussed on: arch (a while a go)
Obtained from: Sandvine Incorporated
Reviewed by: sbruno
Approved by: re (kib)
MFC after: 2 weeks
* Teach the AR5212/AR5416 ANI code to use the RX filter methods, rather
than calling the RX filter routines directly.
* Make HAL_ANI_PRESENT and HAL_ANI_MODE unconditionally available,
regardless of whether ah_ani_function is masking it.
* (Mostly) fully disable ANI if interference mitigation is disabled.
When disabled, the ANI code doesn't touch any ANI/PHY registers,
leaving them the default value. This is in line with what the
Atheros reference driver does.
* Correctly set the ANI parameters during ANI reset, rather than
when ANI is enabled. In this way, if ANI is disabled or enabled
whilst the NIC is not active (and there's no current channel),
bogus parameters or a NULL pointer deference doesn't occur.
There's still some lingering issues - notably, the MIB events/interrupts
aren't fully disabled, so MIB interrupts still occur. I'll worry about
that later.
Approved by: re (kib)
This in particular fixes radar PHY handling - on the AR5212
NIC, one enables the AR_PHY_ERR_RADAR bit in AR_PHY_ERR;
the AR5416 and later also needs a bit set in AR_RX_FILTER.
A follow-up commit is needed to convert the AR5416 ANI code
to use this particular method, as it's currently using the
AR5212 methods directly.
Obtained from: Atheros
Approved by: re (kib)
- Fix usbhidctl and usbhidaction to handle HID devices with multiple
report ids, such as multimedia keyboards.
- Add collection type and report id to the `usbhidctl -r` output. They
are important for proper device understanding and debugging.
- Fix usbhidaction tool to properly handle items having report_count
more then 1.
Approved by: re (kib)
MFC after: 2 weeks
the ADC calibrations if the NIC is in 5ghz 11a or 5ghz HT/20 modes.
I've been told that the dual-ADC is only engaged in turbo/40mhz modes.
Since Sowl (AR9160) seems to return valid-looking calibration data
in 5ghz 20MHz modes, I'm only disabling it for Merlin for now.
It may turn out I can disable it for all chipsets and only enable
it for 40MHz modes.
Approved by: re (kib)
It looks like this was mixed up with the AR9285 calibration code.
This code is now more in line with what Linux ath9k and Atheros
reference drivers do.
Obtained from: Atheros
Approved by: re (kib)
event of a broken or busy fan due to returning incorrect error codes from
the FCU sysctl handler.
Reported by: Path Mather <paul at gromit dot dlib dot vt dot edu>1
Approved by: re (kib)
Although this may not be what the original sysctl was designed to do,
it feels a bit more "expected".
Before, if ANI is disabled, the initial ANI parameters are still written
to the hardware, even if they're not enabled. "ANI enabled" would then
adjust the noise immunity parameters dynamically. Disabling ANI would
simply leave the existing noise immunity parameters where they are,
and disable the dynamic part.
The problem is that disabling ANI doesn't leave the hardware in
a consistent, predictable state - so asking a user to disable ANI
wouldn't actually reset the NIC to a consistent set of PHY signal
detection parameters, resulting in an unpredictable/unreliable outcome.
This makes it difficult to get reliable debugging information from
the user.
Approved by: re (kib)
coordinates, such as digitizers and touch-screens, leaving these devices
to uhid(4) and user-level. Specially patched xf86-input-mouse driver can
handle them, that isn't done and can't be done properly with ums(4)
because of mouse(4) protocol limitations.
Approved by: re (kib)
Slot field of the PxCMD register may point to an empty command slot.
That breaks command timeout detection logic, making impossible to find
what command actually caused timeout, and leading to infinite wait.
Workaround that by checking whether pointed command slot is really used
and can timeout in its time. And if not, fallback to the dumb algorithm
used with FBS -- let all commands to time out and then fail all of them.
Approved by: re (kib)
MFC after: 1 week
respond to any commands. I've found that because of multiple command
retries, each of which cause 30s timeout, bus reset and another retry or
requeue for many commands, it may take ages to eventually drop the
failed device. The odd thing is that those retries continue even after
XPT considered device as dead and invalidated it.
This patch makes cam_periph_error() to block any command retries after
periph was marked as invalid. With that patch all activity completes in
1-2 minutes, just after several timeouts, required to consider device
death. This should make ZFS, gmirror, graid, etc. operation more robust.
Reviewed by: mjacob@ on scsi@
Approved by: re (kib)
data when 'show drives' succeeds, often resulting in a failing exit code
even though the command worked fine.
Reviewed by: bz
Approved by: re (kib)
MFC after: 3 days
the right SIM in case the HBA is RAID-capable but the target in question is
not a hot spare or member of a RAID volume.
- Report the loss and addition of SAS and SATA targets detected via PHY link
status changes and signalled by MPI_EVENT_SAS_DEVICE_STATUS_CHANGE to cam(4)
as lost devices and trigger rescans as appropriate. Without this it can take
quite some time until a lost device actually is no longer tried to be used,
if it ever stops. [1]
- Handle MPI_EVENT_IR2, MPI_EVENT_LOG_ENTRY_ADDED, MPI_EVENT_SAS_DISCOVERY
and MPI_EVENT_SAS_PHY_LINK_STATUS silently as these serve no additional
purpose beyond adding cryptic entries to logs.
Thanks to Hans-Joerg Sirtl for providing one of the HBAs these changes were
developed with and RIP to the mainboard that didn't survive testing them.
PR: 157534 [1]
Approved by: re (kib)
MFC after: 2 weeks
- Sprinkle some const where appropriate.
- Consistently use target_id_t for the target parameter of mpt_map_physdisk()
and mpt_is_raid_volume().
- Fix some whitespace bugs.
Approved by: re (kib)
recommended to allow root users in the jail to access the host system.
PR: docs/156853
Submitted by: crees
Patch by: crees
Approved by: re (kib) for BETA1
you were stuck in an endless loop.
Reported by: kensmith
Approved by: re (kib) for BETA1
Pointy hat to: bz - wonder why I had not tested legacy IP thoroughly..
This is done per request/suggestion from John Baldwin
who introduced the option. Trying to resume normal
system operation after a panic is very unpredictable
and dangerous. It will become even more dangerous
when we allow a thread in panic(9) to penetrate all
lock contexts.
I understand that the only purpose of this option was
for testing scenarios potentially resulting in panic.
Suggested by: jhb
Reviewed by: attilio, jhb
X-MFC-After: never
Approved by: re (kib)
so that it is visible to userland programs. This change enables
the `mount' command with no arguments to be able to show if a
filesystem is mounted using journaled soft updates as opposed
to just normal soft updates.
Approved by: re (bz)
32 bits to 64 bits and eliminates the unused mnt_xflag field. The
existing mnt_flag field is completely out of bits, so this update
gives us room to expand. Note that the f_flags field in the statfs
structure is already 64 bits, so the expanded mnt_flag field can
be exported without having to make any changes in the statfs structure.
Approved by: re (bz)
* Correctly handle -a.
* -A isn't supported.
* Show all closed 1-to-1 and 1-to-many style sockets.
* Show all listening 1-to-many style sockets.
* Use consistent formatting for -W.
PR: 150642
Approved by: re@
MFC after: 4 weeks.
accessing SATA registers. Unserialized access under heavy load caused
wrong speed reporting and potentially could cause device loss.
- To free memory and other resources (including above), allocated
during chipinit() method call on attach, add new chipdeinit() method,
called during driver detach.
Submitted by: Andrew Boyer <aboyer@averesystems.com> (initial version)
Approved by: re (kib)
MFC after: 1 week
Now that the code is in place to audit capability method rights, start
using it to audit the 'rights' argument to cap_new(2).
Approved by: re (kib), mentor (rwatson)
Sponsored by: Google Inc
Since no actual radar data is ever handled, this won't
do anything. It's mostly here as a reference for those who
wish to experiment with radar detection.
Approved by: re (kib)
the resource covers the entire range. Some BIOSes appear to mark
endpoints as non-fixed incorrectly (non-fixed endpoints are supposed to
be used in _PRS when OSPM is allowed to allocate a certain chunk of
address space within a larger range, I don't believe it is supposed to be
used for _CRS).
Approved by: re (kib)
which does not require change in the znode structure.
Specifically, it queries rdev from the znode in the
same sa_bulk_lookup already done in zfs_getattr().
Submitted by: pjd (with some revisions)
Reviewed by: pjd, mm
Approved by: re (kib)
ioctl interface for DFS modules to use.
Since there's no open source dfs code yet, this doesn't introduce any
operational changes.
Approved by: re (kib)
