implemented with macros. This patch improves code readability. Reasoning
behind vidd_* is a sort of "video discipline".
List of macros is supposed to be complete--all methods of video_switch
ought to have their respective macros from now on.
Functionally, this code should be no-op. My intention is to leave current
behaviour of touched code as is.
No objections: rwatson
Silence on: freebsd-current@
Approved by: cognet
implemented with macros. This patch improves code readability. Reasoning
behind kbdd_* is a "keyboard discipline".
List of macros is supposed to be complete--all methods of keyboard_switch
should have their respective macros from now on.
Functionally, this code should be no-op. My intention is to leave current
behaviour of code as is.
Glanced at by: rwatson
Reviewed by: emax, marcel
Approved by: cognet
- Use the correct offsets when copying out the results of PCIOCGETCONF_OLD.
This happened to not affect the 64-bit architectures because there the
addition of pc_domain to struct pcisel didn't change the overall size of
struct pci_conf. [1]
- Always copy the name and unit information to conf_old so it's also part
of the output once this information is cached in dinfo.
- Use the correct type for flags in struct pci_match_conf_old. This
change is more or less cosmetic though.
Reported and tested by: bde [1]
Reviewed by: imp
MFC after: 3 days
Committed from: 24C3
If a mouse has both a wheel and a Z direction we report both.
XXX Due to tradition the wheel is reported as the Z direction (and the Z
direction as W).
Now Apple's Mighty Mouse is fully supported, except the X11 mouse driver
doesn't know what to do with the new coordinate.
MFC after: 3 months
Approved by: njl (mentor), imp
for that argument. This will allow DDB to detect the broad category of
reason why the debugger has been entered, which it can use for the
purposes of deciding which DDB script to run.
Assign approximate why values to all current consumers of the
kdb_enter() interface.
fget() call, that is sleeping point, and possibly dropping Giant.
The snp_target == NULL implies the snp_tty == NULL. Remove the code
that is put under snp_target == NULL and snp_tty != NULL clause.
In snpclose(), do the snp_detach() before scheduling the snp device
destruction. Otherwise, after the return from snpclose(), the snp
device is already removed from the snp_list, but tty is still in
snooped state. Any attempt to do i/o on such tty cause panic because
ttytosnp() returns NULL.
Tested by: Peter Holm
MFC after: 1 week
as multicast/broadcast frames. Previously re(4) ignored multicast
frames in promiscuous mode. The RTL8169 datasheet was not clear
how it handles multicast frames in promiscuous mode.
PR: kern/118572
MFC after: 3 days
NULL and doesn't point to a NULL pointer before dereferencing it. This
fixes a panic triggered by Xorg 7.3.
Reported and tested by: Bill Green
MFC after: 3 days
a pointer to struct bus_space. The structure contains function
pointers that do the actual bus space access.
The reason for this change is that previously all bus space
accesses were little endian (i.e. had an explicit byte-swap
for multi-byte accesses), because all busses on Macs are little
endian.
The upcoming support for Book E, and in particular the E500
core, requires support for big-endian busses because all
embedded peripherals are in the native byte-order.
With this change, there's no distinction between I/O port
space and memory mapped I/O. PowerPC doesn't have I/O port
space. Busses assign tags based on the byte-order only.
For that purpose, two global structures exist (bs_be_tag and
bs_le_tag), of which the address can be taken to get a valid
tag.
Obtained from: Juniper, Semihalf
is actually a circular log. Deal with it rolling around. Fortunately,
the log area is big and I haven't seen any roll over yet. Update and
get rid of the obsolete comment.
and t3_push_frames).
- Import latest changes to cxgb_main.c and cxgb_sge.c from toestack p4 branch
- make driver local copy of tcp_subr.c and tcp_usrreq.c and override tcp_usrreqs so
TOE can also functions on versions with unmodified TCP
- add cxgb back to the build
cards:
o RocketRAID 172x series
o RocketRAID 174x series
o RocketRAID 2210
o RocketRAID 222x series
o RocketRAID 2240
o RocketRAID 230x series
o RocketRAID 231x series
o RocketRAID 232x series
o RocketRAID 2340
o RocketRAID 2522
Many thanks to Highpoint for their continued support of FreeBSD.
Submitted by: Highpoint
it's multi DAC / playback channels is not that good. Enabling vchans
make the bug more visible since playback allocation will look for
possible free hardware channels first (i.e: the next DAC, the very first
has been consumed by vchan mixer) which in this case has been proven faulty.
Tested by: Dominic Fandrey <LoN_Kamikaze at gmx dot de>
URL: http://lists.freebsd.org/pipermail/freebsd-stable/2007-December/039022.html
The HT1000 DMA engine seems to not always like 64K transfers and sometimes barfs data all over memory leading to instant chrash and burn.
Also fix 48bit adressing issues, apparently newer chips needs 16bit writes and not the usual fifo thing.
HW donated by: Travis Mikalson at TerraNovaNet
that favours true hardware channel, the first instance of recording
request will grab this channel (the first channel is being used as
vchan master). In many cases, it is not really work as intended and give
false impression of broken recording.
PR: kern/118546
MFC after: 3 days
Ethernet Controller. Multicast filtering wasn't tested and needs more
expore. While I'm here change complex if statements with switch
statement which would improve readability.
Reported by: Abdullah Ibn Hamad Al-Marri < wearabnet AT yahoo DOT ca >
Tested by: Abdullah Ibn Hamad Al-Marri < wearabnet AT yahoo DOT ca >
pass back the desired buffer length. This fixes scanning with the Marvell
88W8335 and BCM4328 wireless cards.
PR: kern/118370
Submitted by: Weongyo Jeong
Tested by: Ed Schouten
by Daniel Kamm.
Adaptec RAID 51245
Adaptec RAID 51645
Adaptec RAID 52445
Adaptec RAID 5405
Sun STK RAID REM
Sun STK RAID EM
SG-XPCIESAS-R-IN
SG-XPCIESAS-R-EX
initialized before use and returned integrally instead of up to size.
Submitted by: Ilja van Sprundel <ilja -at- netric.org>
Reviewed by: secteam
MFC after: 1 day
is what gcc3 complains about.
Without this change, it's impossible to build the kernel with gcc3.
Tested by: cognet@ (mentor)
Approved by: cognet@ (mentor)
attached. Otherwise, the snp->snp_tty would be overwritten, while the
tty line discipline still set to the snpdisc. Then snplwrite() causes
panic because ttytosnp() cannot find the snp.
MFC after: 1 week
sx driver), change a magic value in the PLX bridge chip. Apparently later
builds of the PCI cards had corrected values in the configuration eeprom.
This change supposedly fixes some pci bus problems.
hack means you can get the units and flags to match up more easily with
serial consoles on machines with acpi tables that cause the com ports
to be probed in the wrong order (and hence get the wrong sio unit number).
This replaces the common alternative hack of editing the code to comment
out the acpi attachment. This could go away entirely when device wiring
patches are committed.
stomping on the units intended for the motherboard sio ports. This is
no real substitute for the not-yet-committed device wiring enhancements.
Code taken from sio's pci attachment.
Intel CPUs with family 0x6, model 0xE and later (i.e., Intel Core(TM))
have a PMC architecture that differs somewhat from previous CPUs in
family 0x6. Even though the basic programming model is similar, the
documented set of legal values that may be loaded into their PMC MSRs
differs from that of the previous PMCs in family 0x6 and reusing bit
values valid for the older PMCs could result in undefined behaviour in
the general case.
T_DIRECT filtering so that disk drives can be attached via the
pass driver. Add CAM locking. Don't mark CAM commands as SG64
since the hardware isn't designed to deal with 64-bit passthru
commands. Hopefully the bounce buffer changes that were done
for the management/ioctl interface are robust enough to handle
this deficiency for CAM as well.
- Enable pcbeep control for Acer + ALC268 (nid 29). Give enough (fake)
hints so the parser will grab it and allocate "speaker" control.
- Fix regression while preparing DAC and ADC for multichannel
format. Since playback policy is to output to every possible path,
ensure that each DAC is started.
Reported / Tested by: Guy Brand
The call should happen with the driver lock held. We don't hold the driver
lock in newstate as it's a separate thread where we can't sleep (and we only
call wpi_cmd in async mode).
Discovered By: Attillo's callout rework
Approved By: mlaier (comentor)
o Acer Aspire 4520 laptop
- jack sensing / automute
o Toshiba Satellite A135-S4527 laptop
- jack sensing / automute
Tested by: lioux
o Apple Macbook 3 (is it?)
- require gpio0 (for speakers) and ovref50 (for headphone)
to make it works
- jack sensing / automute
Tested by: Ed Schouten
* Add Nvidia MCP67 controller ids.
* Be sensible about simmilar controller with multiple pci ids.
* Connect unused DAC/ADC to stream#0 rather than forcing each of them
managing their own stream.
MFC after: 3 days
- Bring HEAD up to the latest shared code
- Fix TSO problem using limited MSS and forwarding
- Dual lock implementation
- New device support
- For my ease, this code can compile in either 6.x or later
- brings this driver in sync with the 6.3
only at address 0 which is supposed to be the only valid phy address
on Marvell PHY. The more correct solution would be masking PHY
address ranges allowable in PHY probe routine. Unfortunately,
FreeBSD has no way to retrict the PHY address ranges or to pass special
flags to PHY driver.
This change assumes that PHY hardwares attached to msk(4) would be
Marvell made 88E11xx PHY.
With this changes the phantom phys attached on 88E8036(Yukon FE)
should disappear.
Reported by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
Tested by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
only 4KB SRAM.
o Rework setting Tx/Rx RAM buffer size. Give receiver 2/3 of memory
and round it down to the multiple of 1024. The RAM buffer size of
Yukon II should be multiple of 1024. This fixes bogus RAM buffer
configuration used in Yukon FE.
Reported by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
Tested by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
publicly available datasheet for Yukon II and don't know what
bug/workaround exist for the specific hardware revision. Also I don't
think the vendor will release hardware errata in near future.
The hardware feature lists were not used at all except setting water
mark registers. Since msk(4) should know exact chip model/revision
number to decide which hardware capability could be used the extra
feature lists were redundant.
o Enable jumbo frame support for EC Ultra and disable jumbo frame
for FE.
o Enable store and forward mode for standard MTU sized frame.
o Enable TSO for EC Ultra. However TSO/checksum offload is disabled
for jumbo frame case. Because EC Ultra can't use store and forward
mode for jumbo frame TSO/checksum offload is not available.
o Adjust Tx GMAC almost empty threshold value and add a jumbo frame
water mark. The maic value was obtained from Marvell's sk98lin
driver.
o Fix EC Ultra chip revision number.
Revert the probe in atapi-cd.c to the old usage now its fixed on AHCI.
THis change also fixes using virtual CD's om fx parallels.
Still leaves the GEOM problem of telling media vs device access apart in the access function.
- Implement timing out of VPD register access.[1]
- Fix an off-by-one error of freeing malloc'd space when checksum is invalid.
- Fix style(9) bugs, i.e., sizeof cannot be followed by space.
- Retire now obsolete 'hw.pci.enable_vpd' tunable.
Submitted by: cokane (initial revision)[1]
Reviewed by: marius (intermediate revision)
Silence from: jhb, jmg, rwatson
Tested by: cokane, jkim
MFC after: 3 days
The register layout is little different from memory-mapped stats
in the previous generation chips. In fact, it is bad because
registers in this range are cleared after reading them.
Reviewed by: scottl
MFC after: 3 days
- Trying to eliminate another racing by replacing the timeout(9) with
callout APIs. In addition to that, the callout_drain() in an_detach()
help us to avoid a possible panic-on-free due to the callout API tries
to lock a destroyed mutex.
- In an_stats_update(), check the return value of an_read_record(). This
should reduce the chance of device removal(PCCARD) panic [2].
- Adding a comment to state the fact that an_stats_update() is now called
via callout(9) with a lock held [2].
Submitted by: jhb [1], ambrisko [2]
Reviewed by: jhb, ambrisko
Reported by: dhw
Tested by: dhw
MFC after: 3 days
priorities of the technologies supported by 802.3 Selector Field
value.
1000BASE-T full duplex
1000BASE-T
100BASE-T2 full duplex
100BASE-TX full duplex
100BASE-T2
100BASE-T4
100BASE-TX
10BASE-T full duplex
10BAST-T
However PHY drivers didn't honor the order such that 100BASE-T4 had
higher priority than 100BASE-TX full duplex. Fix that long standing
bugs such that have PHY drivers choose the highest common denominator
ability.
Fix a bug in dcphy which inadvertently aceepts 100BASE-T4.
PR: 92599
that the driver will handle WEP encryption. However, this does not seem to be
implemented by this driver (or maybe the chipset doesn't support it?)
Removing the flag makes my wpi card work using wpa_supplicant(8) on a
network with 802.1x security (without this change it authenticated fine, but
tcpdump only saw garbage packets)
Reviewed by: benjsc, imp (mentor)
Approved by: imp (mentor), sam
bumped to 800004 to note the change though userland apps should not be
affected since they use <sys/agpio.h> rather than the headers in
sys/dev/agp.
Discussed with: anholt
Repocopy by: simon
and update the rx code to handle multiple frames in a single usb
transfer. AX772 parts (at least) exhibit many input errors when
operated with a 2K rx buffer and no errors w/ a 4K rx buffer (it's
unclear what the cause of the errors is for 2K so this may just be
covering up the real issue). Larger rx buffer sizes show no
significant performance improvement for AX772. Bypassing the common
buffer management routines also eliminates an extra context switch
on every packet which noticeably improves performance (TCP netperf
rx goes from 45 Mb/s to 85 MB/s).
Submitted by: "J.R. Oldroyd" <fbsd@opal.com>
Reviewed by: imp
Obtained from: openbsd (partly)
MFC after: 3 weeks
The reliability of it's multi DAC / playback channels is
not that good. Enabling vchans make the bug more visible
since playback allocation will look for possible free
hardware channels first (i.e: the next DAC, the very first
has been consumed by vchan mixer) which in this case has
been proven faulty.
Reported / Tested by: Sascha Klauder
MFC after: 3 days
- Patch registers CR47 and CR157 on devices that require it.
- Fix power calibration setting on ZD1211B.
Obtained from: OpenBSD
- Fix multicast transfer by properly reprogram multicast global
hash table, which in turns fix promiscuous mode and IPv6
autoconfiguration / local networking.
Reviewed by: sam, Weongyo Jeong
Tested using: Aztech WL230 , Belkin F5D7050, Unicorn WL-54G,
3COM 3CRUSB10075
MFC after: 1 week
I've tried to move md(4) to use geom_disk class, like real disks do, but
this requires major rework of some of the existing features such as
configuration dumping for example. Therefore just putting devstat support
directly into md(4) seems to be optimal solution.
Now you can see md(4) stats in `systat -vm' again.
MFC after: 2 weeks
present on the MacBook, MacBook Pro, and Intel MacMini.
This driver exports information via sysctl in its private sysctl tree
dev.asmc.*. You can get information about temperatures, fan speeds, the
keyboard light sensor and the Sudden Motion Sensor (SMS).
The SMS is very useful to park the disk heads when the laptop is
moved. Basically, the SMS is setup so that, under movement, we get an
interrupt on irq 6 and a devd notification is sent.
Sponsored by: Google Summer of Code 2007
Approved by: njl (mentor)
Reviewed by: attilio (previous version, but very similar), jhb (interrupt
specific review)
while other variants have inorder ethernet address for the same
chipset. Override ethernet address ordering if we already know how
it was stored. This fixes the use of inversed ethernet address on
MCP67.
Submitted by: ariff
MFC after: 3 days
Allocate space in keyboard state structure instead to prevent random byte
from possibly overwritten stack location frombeing shoved into USB device
when transfer actually takes place.
This fixes at least one instance of LEDs not working with USB keyboards.
This import includes:
o wpi Wireless driver for the Intel 3945 Wireless Lan Controller (802.11abg) (sys/dev/wpi)
o Intel firmware revision 2.14.4 & associated LICENSE (sys/dev/contrib/wpi, sys/contrib/dev/wpi/LICENSE)
o wpifw Firmware driver (sys/modules/wpifw)
Approved by: mlaier, sam (co-mentors)
reset problem when we reboot the system with the zyd device inserted.
Submitted by: Weongyo Jeong
Reported by: Ted Lindgreen (ted@tednet.nl)
MFC after: 1 week
it's been printing out scary messages about "Unhanded Event Notify Frame"
that are needlessly worrisome to users. Change this warning to only print
out at an elevated debugging level.
CPUs to make sure idle threads are evicted from the softc before returning
from acpi_cpu_shutdown(). However, this is unnecessary since stop_cpus()
handles this for itself and at this point it's possible that our IPI will be
blocked (interrupts disabled).
Thanks to: Glen Leeder <glen.leeder / nokia.com>
MFC after: 3 days
/dev/agpgart and agp_free_res() frees resources like the BAR for the
aperture. Splitting this up lets chipset-specific detach routines
manipulate the aperture during their detach routines without panicing.
MFC after: 1 week
Reviewed by: anholt
set this flag and it was more or less just copied and pasted from
another FreeBSD driver while porting this driver from NetBSD, whose
gentbi(4) doesn't set MIIF_NOISOLATE either.
- Fix spelling in a comment.
OK'ed by: yongari
MFC after: 3 months
changes:
01 - Enhanced LRO:
LRO feature is extended to support multi-buffer mode. Previously,
Ethernet frames received in contiguous buffers were offloaded.
Now, frames received in multiple non-contiguous buffers can be
offloaded, as well. The driver now supports LRO for jumbo frames.
02 - Locks Optimization:
The driver code was re-organized to limit the use of locks.
Moreover, lock contention was reduced by replacing wait locks
with try locks.
03 - Code Optimization:
The driver code was re-factored to eliminate some memcpy
operations. Fast path loops were optimized.
04 - Tag Creations:
Physical Buffer Tags are now optimized based upon frame size.
For better performance, Physical Memory Maps are now re-used.
05 - Configuration:
Features such as TSO, LRO, and Interrupt Mode can be configured
either at load or at run time. Rx buffer mode (mode 1 or mode 2)
can be configured at load time through kenv.
06 - Driver Statistics:
Run time statistics are enhanced to provide better visibility
into the driver performance.
07 - Bug Fixes:
The driver contains fixes for the problems discovered and
reported since last submission.
08 - MSI support:
Added Message Signaled Interrupt feature which currently uses 1
message.
09 Removed feature:
Rx 3 buffer mode feature has been removed. Driver now supports 1,
2 and 5 buffer modes of which 2 and 5 buffer modes can be used
for header separation.
10 Compiler warning:
Fixed compiler warning when compiled for 32 bit system.
11 Copyright notice:
Source files are updated with the proper copyright notice.
MFC after: 3 days
Submitted by: Alicia Pena <Alicia dot Pena at neterion dot com>,
Muhammad Shafiq <Muhammad dot Shafiq at neterion dot com>
