only at address 0 which is supposed to be the only valid phy address
on Marvell PHY. The more correct solution would be masking PHY
address ranges allowable in PHY probe routine. Unfortunately,
FreeBSD has no way to retrict the PHY address ranges or to pass special
flags to PHY driver.
This change assumes that PHY hardwares attached to msk(4) would be
Marvell made 88E11xx PHY.
With this changes the phantom phys attached on 88E8036(Yukon FE)
should disappear.
Reported by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
Tested by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
only 4KB SRAM.
o Rework setting Tx/Rx RAM buffer size. Give receiver 2/3 of memory
and round it down to the multiple of 1024. The RAM buffer size of
Yukon II should be multiple of 1024. This fixes bogus RAM buffer
configuration used in Yukon FE.
Reported by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
Tested by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
publicly available datasheet for Yukon II and don't know what
bug/workaround exist for the specific hardware revision. Also I don't
think the vendor will release hardware errata in near future.
The hardware feature lists were not used at all except setting water
mark registers. Since msk(4) should know exact chip model/revision
number to decide which hardware capability could be used the extra
feature lists were redundant.
o Enable jumbo frame support for EC Ultra and disable jumbo frame
for FE.
o Enable store and forward mode for standard MTU sized frame.
o Enable TSO for EC Ultra. However TSO/checksum offload is disabled
for jumbo frame case. Because EC Ultra can't use store and forward
mode for jumbo frame TSO/checksum offload is not available.
o Adjust Tx GMAC almost empty threshold value and add a jumbo frame
water mark. The maic value was obtained from Marvell's sk98lin
driver.
o Fix EC Ultra chip revision number.
Revert the probe in atapi-cd.c to the old usage now its fixed on AHCI.
THis change also fixes using virtual CD's om fx parallels.
Still leaves the GEOM problem of telling media vs device access apart in the access function.
- Implement timing out of VPD register access.[1]
- Fix an off-by-one error of freeing malloc'd space when checksum is invalid.
- Fix style(9) bugs, i.e., sizeof cannot be followed by space.
- Retire now obsolete 'hw.pci.enable_vpd' tunable.
Submitted by: cokane (initial revision)[1]
Reviewed by: marius (intermediate revision)
Silence from: jhb, jmg, rwatson
Tested by: cokane, jkim
MFC after: 3 days
The register layout is little different from memory-mapped stats
in the previous generation chips. In fact, it is bad because
registers in this range are cleared after reading them.
Reviewed by: scottl
MFC after: 3 days
- Trying to eliminate another racing by replacing the timeout(9) with
callout APIs. In addition to that, the callout_drain() in an_detach()
help us to avoid a possible panic-on-free due to the callout API tries
to lock a destroyed mutex.
- In an_stats_update(), check the return value of an_read_record(). This
should reduce the chance of device removal(PCCARD) panic [2].
- Adding a comment to state the fact that an_stats_update() is now called
via callout(9) with a lock held [2].
Submitted by: jhb [1], ambrisko [2]
Reviewed by: jhb, ambrisko
Reported by: dhw
Tested by: dhw
MFC after: 3 days
priorities of the technologies supported by 802.3 Selector Field
value.
1000BASE-T full duplex
1000BASE-T
100BASE-T2 full duplex
100BASE-TX full duplex
100BASE-T2
100BASE-T4
100BASE-TX
10BASE-T full duplex
10BAST-T
However PHY drivers didn't honor the order such that 100BASE-T4 had
higher priority than 100BASE-TX full duplex. Fix that long standing
bugs such that have PHY drivers choose the highest common denominator
ability.
Fix a bug in dcphy which inadvertently aceepts 100BASE-T4.
PR: 92599
that the driver will handle WEP encryption. However, this does not seem to be
implemented by this driver (or maybe the chipset doesn't support it?)
Removing the flag makes my wpi card work using wpa_supplicant(8) on a
network with 802.1x security (without this change it authenticated fine, but
tcpdump only saw garbage packets)
Reviewed by: benjsc, imp (mentor)
Approved by: imp (mentor), sam
bumped to 800004 to note the change though userland apps should not be
affected since they use <sys/agpio.h> rather than the headers in
sys/dev/agp.
Discussed with: anholt
Repocopy by: simon
and update the rx code to handle multiple frames in a single usb
transfer. AX772 parts (at least) exhibit many input errors when
operated with a 2K rx buffer and no errors w/ a 4K rx buffer (it's
unclear what the cause of the errors is for 2K so this may just be
covering up the real issue). Larger rx buffer sizes show no
significant performance improvement for AX772. Bypassing the common
buffer management routines also eliminates an extra context switch
on every packet which noticeably improves performance (TCP netperf
rx goes from 45 Mb/s to 85 MB/s).
Submitted by: "J.R. Oldroyd" <fbsd@opal.com>
Reviewed by: imp
Obtained from: openbsd (partly)
MFC after: 3 weeks
The reliability of it's multi DAC / playback channels is
not that good. Enabling vchans make the bug more visible
since playback allocation will look for possible free
hardware channels first (i.e: the next DAC, the very first
has been consumed by vchan mixer) which in this case has
been proven faulty.
Reported / Tested by: Sascha Klauder
MFC after: 3 days
- Patch registers CR47 and CR157 on devices that require it.
- Fix power calibration setting on ZD1211B.
Obtained from: OpenBSD
- Fix multicast transfer by properly reprogram multicast global
hash table, which in turns fix promiscuous mode and IPv6
autoconfiguration / local networking.
Reviewed by: sam, Weongyo Jeong
Tested using: Aztech WL230 , Belkin F5D7050, Unicorn WL-54G,
3COM 3CRUSB10075
MFC after: 1 week
I've tried to move md(4) to use geom_disk class, like real disks do, but
this requires major rework of some of the existing features such as
configuration dumping for example. Therefore just putting devstat support
directly into md(4) seems to be optimal solution.
Now you can see md(4) stats in `systat -vm' again.
MFC after: 2 weeks
present on the MacBook, MacBook Pro, and Intel MacMini.
This driver exports information via sysctl in its private sysctl tree
dev.asmc.*. You can get information about temperatures, fan speeds, the
keyboard light sensor and the Sudden Motion Sensor (SMS).
The SMS is very useful to park the disk heads when the laptop is
moved. Basically, the SMS is setup so that, under movement, we get an
interrupt on irq 6 and a devd notification is sent.
Sponsored by: Google Summer of Code 2007
Approved by: njl (mentor)
Reviewed by: attilio (previous version, but very similar), jhb (interrupt
specific review)
while other variants have inorder ethernet address for the same
chipset. Override ethernet address ordering if we already know how
it was stored. This fixes the use of inversed ethernet address on
MCP67.
Submitted by: ariff
MFC after: 3 days
Allocate space in keyboard state structure instead to prevent random byte
from possibly overwritten stack location frombeing shoved into USB device
when transfer actually takes place.
This fixes at least one instance of LEDs not working with USB keyboards.
This import includes:
o wpi Wireless driver for the Intel 3945 Wireless Lan Controller (802.11abg) (sys/dev/wpi)
o Intel firmware revision 2.14.4 & associated LICENSE (sys/dev/contrib/wpi, sys/contrib/dev/wpi/LICENSE)
o wpifw Firmware driver (sys/modules/wpifw)
Approved by: mlaier, sam (co-mentors)
reset problem when we reboot the system with the zyd device inserted.
Submitted by: Weongyo Jeong
Reported by: Ted Lindgreen (ted@tednet.nl)
MFC after: 1 week
it's been printing out scary messages about "Unhanded Event Notify Frame"
that are needlessly worrisome to users. Change this warning to only print
out at an elevated debugging level.
CPUs to make sure idle threads are evicted from the softc before returning
from acpi_cpu_shutdown(). However, this is unnecessary since stop_cpus()
handles this for itself and at this point it's possible that our IPI will be
blocked (interrupts disabled).
Thanks to: Glen Leeder <glen.leeder / nokia.com>
MFC after: 3 days
/dev/agpgart and agp_free_res() frees resources like the BAR for the
aperture. Splitting this up lets chipset-specific detach routines
manipulate the aperture during their detach routines without panicing.
MFC after: 1 week
Reviewed by: anholt
set this flag and it was more or less just copied and pasted from
another FreeBSD driver while porting this driver from NetBSD, whose
gentbi(4) doesn't set MIIF_NOISOLATE either.
- Fix spelling in a comment.
OK'ed by: yongari
MFC after: 3 months
changes:
01 - Enhanced LRO:
LRO feature is extended to support multi-buffer mode. Previously,
Ethernet frames received in contiguous buffers were offloaded.
Now, frames received in multiple non-contiguous buffers can be
offloaded, as well. The driver now supports LRO for jumbo frames.
02 - Locks Optimization:
The driver code was re-organized to limit the use of locks.
Moreover, lock contention was reduced by replacing wait locks
with try locks.
03 - Code Optimization:
The driver code was re-factored to eliminate some memcpy
operations. Fast path loops were optimized.
04 - Tag Creations:
Physical Buffer Tags are now optimized based upon frame size.
For better performance, Physical Memory Maps are now re-used.
05 - Configuration:
Features such as TSO, LRO, and Interrupt Mode can be configured
either at load or at run time. Rx buffer mode (mode 1 or mode 2)
can be configured at load time through kenv.
06 - Driver Statistics:
Run time statistics are enhanced to provide better visibility
into the driver performance.
07 - Bug Fixes:
The driver contains fixes for the problems discovered and
reported since last submission.
08 - MSI support:
Added Message Signaled Interrupt feature which currently uses 1
message.
09 Removed feature:
Rx 3 buffer mode feature has been removed. Driver now supports 1,
2 and 5 buffer modes of which 2 and 5 buffer modes can be used
for header separation.
10 Compiler warning:
Fixed compiler warning when compiled for 32 bit system.
11 Copyright notice:
Source files are updated with the proper copyright notice.
MFC after: 3 days
Submitted by: Alicia Pena <Alicia dot Pena at neterion dot com>,
Muhammad Shafiq <Muhammad dot Shafiq at neterion dot com>
made by Michael Eisele and the patch was slightly modified by me.
With this change several NVIDIA ethernet controllers(e.g. MCP61)
works.
RTL8211B(L) is RealTek's new gigabit PHY. The PHY has several
features including crossover correction, polarity correction as
well as supporting triple speed(10/100/1000bps). Data transfer
between MAC and PHY is via RGMII for 1000baseT, MII for
10baseT/100baseTX.
Unfortunately, RealTek used the same model number for RTL8211B(L)
PHY so there is no way to discriminate between RTL8211B(L) and its
predecessors. ATM RTL8211B uses revision number 2 so checking the
revision number seems to be only way to identify it.
Obtained from: Michael Eisele [1]
Tested by: clemens fischer < ino-qc AT spotteswoode DOT de DOT eu DOT org >
mii_anegticks to MII_ANEGTICKS_GIGE and use it. Previously it used
to MII_ANEGTICKS which may not be enough to wait before retrying
autonegotiation process at 1000bps.
o Reset autonegotation timer if media option is not IFM_AUTO or we
got a valid link.
o Announce link loss right after it happends.
o Autonegiation is retried every mii_anegticks seconds.
o Report link state changes right after setting autonegotiation.
reason (not all BIOSen have _DIS methods for all link devices for example).
This matches the behavior of attach() with respect to _DIS as well.
Submitted by: njl
handle to the PCI device_t if the ACPI device_t is already attached to a
driver. This happens on the Tablet TC1000 which for some reason includes
two PCI-ISA bridges and treats the second bridge as an ACPI system resource
device.
Reviewed by: njl (a while ago)
MFC after: 3 days
refactored it to be a generic device.
Instead of being part of the standard kernel, there is now a 'nvram' device
for i386/amd64. It is in DEFAULTS like io and mem, and can be turned off
with 'nodevice nvram'. This matches the previous behavior when it was
first committed.
the PS/2 mouse controller. Thus, when acpi_ibm(4) claimed the mouse
device, the mouse would stop working. The one ACPI dump of an R40 that
I've looked at includes an HKEY device with the proper "IBM0068" ID, so
I'm not sure how the "IBM0057" ID could have helped at all.
MFC after: 1 week
Approved by: njl
the PCIOCGETCONF, PCIOCREAD and PCIOCWRITE IOCTLs, which was broken
with the introduction of PCI domain support.
As the size of struct pci_conf_io wasn't changed with that commit,
this unfortunately requires the ABI of PCIOCGETCONF to be broken
again in order to be able to provide backwards compatibility to
the old version of that IOCTL.
Requested by: imp
Discussed with: re (kensmith)
Reviewed by: PCI maintainers (imp, jhb)
MFC after: 5 days
to kproc_xxx as they actually make whole processes.
Thos makes way for us to add REAL kthread_create() and friends
that actually make theads. it turns out that most of these
calls actually end up being moved back to the thread version
when it's added. but we need to make this cosmetic change first.
I'd LOVE to do this rename in 7.0 so that we can eventually MFC the
new kthread_xxx() calls.
codecs. Codec at address 0 seems purely digital, or perhaps an HDMI
interface. Let the driver skip it and continue scanning the codecs
starting with address 2 (Realtek ALC885).
* Due to possibilities of future similar cases, put enough logic
in hdac_scan_codecs() to force codec scanning starting from
XX address via tunable "hint.pcm.%d.codec_index".
Reported / Tested by: Toomas Pelberg <toomasp@gmx.net>
- Trivial headphone / speaker automute fixup for Fujitsu-Siemens
AMILO Si 1848 laptop.
Reported / Tested by: Ed <ed@bsd.it>
- Trivial headphone / speaker automute fixup for Fujitsu-Siemens
Lifebook S7020D laptop.
Reported / Tested by: Jaromir Dvoracek <jarek@ataxo.com>
- Some smart vendor trying to create interplanetary wormhole by
screwing pci config space during their BIOS update. The side effects
of their failure attempt includes mutilated hardware id, broken
speaker automuting and loosing the entire analog CD connectivity,
thus causing enough collateral damages to collapse the entire
universe. Move along with it.
Please exercise extra cautious when applying BIOS updates.
Reported / Tested by: Pietro Cerutti <gahr@gahr.ch>
- assembled laptop, based on the MSI-1034
(662) which is now becoming MSI-034A.
- Fix no sound issues (on headphones) for Lenovo ThinkCentre A55 due
to global automute table entry which is not applicable for
non-laptops.
Reported / Tested by: Piotr Smyrak <piotr.smyrak@heron.pl>
- Speaker mute control for HP DC7700 since the front headphone jack
does not generate any interesting unsolicited signal/response.
Reported / Tested by: tyop @ irc.freenode.net
Approved by: re (kensmith)
MFC after: 3 days
ukbd_poll to mark this keyboard instance as polling before calling
usbd_set_polling at USB level. usbd_set_polling runs softintr before
returning, stealing our input and making consequent polling getchar
kind of pointless.
This allows USB keyboards to coexist peacefully with serial console in DDB
and other contexts where polling is used.
MFC after: 1 week
properly due to the shortage of the RX buffer size. In a case of zyd
devices, up to 3 frames can be combined in an USB transaction. So, RX
buffer should be at least ((MCLBYTES + extra structs) * 3)
Submitted by: Weongyo Jeong <weongyo.jeong@gmail.com>
MFC after: 3 days
make sure to never call sched_bind() for uninitialised CPUs.
Submitted by: Constantine A. Murenin <cnst@FreeBSD.org>
Sponsored by: Google Summer of Code 2007 (GSoC2007/cnst-sensors)
Mentored by: syrinx
Tested by: many
OKed by: kensmith
which is ukbd0. Specifically, the keyboard driver structures for ukbd0
are not allocated/freed but are statically allocated via a persistent
global variable. There is some additional magic for the ukbd0 such that
if the keyboard is marked as probed in this global variable, then we
don't check to see if the device_t we are probing has an interface.
This causes a problem if an attach of ukbd0 fails without fulling clearing
the state in the global variable. Specifically, if the keyboard fails to
initialize in init_keyboard() or kbd_register(), then the keyboard will
still be marked as probed. The USB layer will then try to offer the
"generic" version of the USB keyboard device (as opposed to the
per-interface sub-devices) and the ukbd(4) driver will see that the
keyboard is marked probe and will skip the "is this a per-interface device"
check. Later in ukbd_attach() it panics because it tries to dereference
the interface pointer which is NULL.
The fix is to clear the flags in the persistent keyboard data for ukbd0
when init_keyboard() or kbd_register() fail.
MFC after: 1 week
Reviewed by: imp
- Add proper scanning support rather than letting the firmware grab the first
access point
- Overhaul state changes
- Use macros for locking and provide _locked() versions of some functions
- Increase debugging output
- Use a callout rather than the old watchdog interface
- Improve style, function names and defines
- Add WPA (TKIP) support
Based heavily on a patchset provided by Sam Leffler.
VR_STICKHW register would result in unexpected results on these
hardwares. wpaul said the following for the issue.
The vr_attach() routine unconditionally does this for all supported
chips:
/*
* Windows may put the chip in suspend mode when it
* shuts down. Be sure to kick it in the head to wake it
* up again.
*/
VR_CLRBIT(sc, VR_STICKHW, (VR_STICKHW_DS0|VR_STICKHW_DS1));
The problem is, the VR_STICKHW register is not valid on all Rhine
devices. The VT86C100A chip, which is present on the D-Link DFE-530TX
boards, doesn't support power management, and its register space is
only 128 bytes wide. The VR_STICKHW register offset falls outside this
range. This may go unnoticed in most scenarios, but if you happen to have
another PCI device in your system which is assigned the register
space immediately after that of the Rhine, the vr(4) driver will
incorrectly stomp it. In my case, the BIOS on my test board decided
to put the register space for my PRO/100 ethernet board right next
to the Rhine, and the Rhine driver ended up clobbering the IMR register
of the PRO/100 device. (Long story short: the board kept locking up on
boot. Took me the better part of the morning suss out why.)
The strictly correct thing to do would be to check the PCI config space
to make sure the device supports the power management capability and only
write to the VR_STICKHW register if it does.
Instead of inspecting chip revision numbers for the availability of
VR_STICKHW register, check the existence of power management capability
of the hardware as wpaul suggested.
Reported by: wpaul
Suggested by: wpaul
OK'ed by: jhb
SAS-enabled cards. It also makes the driver MPSAFE, eliminating some
problems that resulted from CAM becoming MPSAFE. Many thanks to 3Ware/AMCC
for continuing to support FreeBSD.
Submitted by: Manjunath Ranganathaiah
Approved by: re
voltage of 0. This can result in a divide by zero trap. Add a guard
for this case. The value of lfcap is checked in acpi_battery_bif_valid()
just before this, so it is safe.
Reportd by: sam
Approved by: re
MFC after: 3 days
of directly from acpi0. Before it would attach prior to the sysresource
devices, causing the later allocation of its memory range to fail and
print a warning like "acpi0: reservation of fed00000, 1000 (3) failed".
Use an explicit define for our probe order base value of 10.
Help from: jhb
Tested by: Abdullah Ibn Hamad Al-Marri <almarrie / gmail.com>
MFC after: 3 days
Approved by: re
with all functions supported. This is done adding usb device IDs
to the table of recognised devices (because there is no standard
'scanner' class, so no other way to recognise them), and with
a small change to the uscanner attach routine that prevents
reconfiguring the whole USB device while we are dealing only with
one of its USB interfaces.
The latter part has been suggested by Steinar Hamre in
http://www.freebsd.org/cgi/query-pr.cgi?pr=107665 , i have
only added a bit of explaination to the code.
I have personally tried this on the Epson DX-5050 and DX-6000
devices (on the US market they have different names, CX-something).
I have good reasons to think that, possibly with the mere addition
of more USB ids to the table in uscanner.c, this should work with
all Epson multifunction devices in that family (from DX-3800 to
DX-7000 - these units are in the 50-120$ price range).
More details on related topics (SANE configuration, OCR, etc.)
at http://info.iet.unipi.it/~luigi/FreeBSD/dx5050.html
Manpage updates coming soon.
Approved by: re, imp
MFC after: 3 days
UDMA modes.
Please notice that Soekris NET5501 bios versions before 1.32f has a bug
that prevents this from working.
Approved by: re (gnn)
MFC: 2 weeks
support machines having multiple independently numbered PCI domains
and don't support reenumeration without ambiguity amongst the
devices as seen by the OS and represented by PCI location strings.
This includes introducing a function pci_find_dbsf(9) which works
like pci_find_bsf(9) but additionally takes a domain number argument
and limiting pci_find_bsf(9) to only search devices in domain 0 (the
only domain in single-domain systems). Bge(4) and ofw_pcibus(4) are
changed to use pci_find_dbsf(9) instead of pci_find_bsf(9) in order
to no longer report false positives when searching for siblings and
dupe devices in the same domain respectively.
Along with this change the sole host-PCI bridge driver converted to
actually make use of PCI domain support is uninorth(4), the others
continue to use domain 0 only for now and need to be converted as
appropriate later on.
Note that this means that the format of the location strings as used
by pciconf(8) has been changed and that consumers of <sys/pciio.h>
potentially need to be recompiled.
Suggested by: jhb
Reviewed by: grehan, jhb, marcel
Approved by: re (kensmith), jhb (PCI maintainer hat)
to gem_attach() as the former access softc members not yet initialized
at that time and gem_reset() actually is enough to stop the chip. [1]
o Revise the use of gem_bitwait(); add bus_barrier() calls before calling
gem_bitwait() to ensure the respective bit has been written before we
starting polling on it and poll for the right bits to change, f.e. even
though we only reset RX we have to actually wait for both GEM_RESET_RX
and GEM_RESET_TX to clear. Add some additional gem_bitwait() calls in
places we've been missing them according to the GEM documentation.
Along with this some excessive DELAYs, which probably only were added
because of bugs in gem_bitwait() and its use in the first place, as
well as as have of an gem_bitwait() reimplementation in gem_reset_tx()
were removed.
o Add gem_reset_rxdma() and use it to deal with GEM_MAC_RX_OVERFLOW errors
more gracefully as unlike gem_init_locked() it resets the RX DMA engine
only, causing no link loss and the FIFOs not to be cleared. Also use it
deal with GEM_INTR_RX_TAG_ERR errors, with previously were unhandled.
This was based on information obtained from the Linux GEM and OpenSolaris
ERI drivers.
o Turn on workarounds for silicon bugs in the Apple GMAC variants.
This was based on information obtained from the Darwin GMAC and Linux GEM
drivers.
o Turn on "infinite" (i.e. maximum 31 * 64 bytes in length) DMA bursts.
This greatly improves especially RX performance.
o Optimize the RX path, this consists of:
- kicking the receiver as soon as we've a spare descriptor in gem_rint()
again instead of just once after all the ready ones have been handled;
- kicking the receiver the right way, i.e. as outlined in the GEM
documentation in batches of 4 and by pointing it to the descriptor
after the last valid one;
- calling gem_rint() before gem_tint() in gem_intr() as gem_tint() may
take quite a while;
- doubling the size of the RX ring to 256 descriptors.
Overall the RX performance of a GEM in a 1GHz Sun Fire V210 was improved
from ~100Mbit/s to ~850Mbit/s.
o In gem_add_rxbuf() don't assign the newly allocated mbuf to rxs_mbuf
before calling bus_dmamap_load_mbuf_sg(), if bus_dmamap_load_mbuf_sg()
fails we'll free the newly allocated mbuf, unable to recycle the
previous one but a NULL pointer dereference instead.
o In gem_init_locked() honor the return value of gem_meminit().
o Simplify gem_ringsize() and dont' return garbage in the default case.
Based on OpenBSD.
o Don't turn on MAC control, MIF and PCS interrupts unless GEM_DEBUG is
defined as we don't need/use these interrupts for operation.
o In gem_start_locked() sync the DMA maps of the descriptor rings before
every kick of the transmitter and not just once after enqueuing all
packets as the NIC might instantly start transmitting after we kicked
it the first time.
o Keep state of the link state and use it to enable or disable the MAC
in gem_mii_statchg() accordingly as well as to return early from
gem_start_locked() in case the link is down. [3]
o Initialize the maximum frame size to a sane value.
o In gem_mii_statchg() enable carrier extension if appropriate.
o Increment if_ierrors in case of an GEM_MAC_RX_OVERFLOW error and in
gem_eint(). [3]
o Handle IFF_ALLMULTI correctly; don't set it if we've turned promiscuous
group mode on and don't clear the flag if we've disabled promiscuous
group mode (these were mostly NOPs though). [2]
o Let gem_eint() also report GEM_INTR_PERR errors.
o Move setting sc_variant from gem_pci_probe() to gem_pci_attach() as
device probe methods are not supposed to touch the softc.
o Collapse sc_inited and sc_pci into bits for sc_flags.
o Add CTASSERTs ensuring that GEM_NRXDESC and GEM_NTXDESC are set to
legal values.
o Correctly set up for 802.3x flow control, though #ifdef out the code
that actually enables it as this needs more testing and mainly a proper
framework to support it.
o Correct and add some conversions from hard-coded functions names to
__func__ which were borked or forgotten in if_gem.c rev. 1.42.
o Use PCIR_BAR instead of a homegrown macro.
o Replace sc_enaddr[6] with sc_enaddr[ETHER_ADDR_LEN].
o In gem_pci_attach() in case attaching fails release the resources in
the opposite order they were allocated.
o Make gem_reset() static to if_gem.c as it's not needed outside that
module.
o Remove the GEM_GIGABIT flag and the associated code; GEM_GIGABIT was
never set and the associated code was in the wrong place.
o Remove sc_mif_config; it was only used to cache the contents of the
respective register within gem_attach().
o Remove the #ifdef'ed out NetBSD/OpenBSD code for establishing a suspend
hook as it will never be used on FreeBSD.
o Also probe Apple Intrepid 2 GMAC and Apple Shasta GMAC, add support for
Apple K2 GMAC. Based on OpenBSD.
o Add support for Sun GBE/P cards, or in other words actually add support
for cards based on GEM to gem(4). This mainly consists of adding support
for the TBI of these chips. Along with this the PHY selection code was
rewritten to hardcode the PHY number for certain configurations as for
example the PHY of the on-board ERI of Blade 1000 shows up twice causing
no link as the second incarnation is isolated.
These changes were ported from OpenBSD with some additional improvements
and modulo some bugs.
o Add code to if_gem_pci.c allowing to read the MAC-address from the VPD on
systems without Open Firmware.
This is an improved version of my variant of the respective code in
if_hme_pci.c
o Now that gem(4) is MI enable it for all archs.
Pointed out by: yongari [1]
Suggested by: rwatson [2], yongari [3]
Tested on: i386 (GEM), powerpc (GMACs by marcel and yongari),
sparc64 (ERI and GEM)
Reviewed by: yongari
Approved by: re (kensmith)
polling/interrupt-driven fallback and instead use polling only during
boot and pure interrupt-driven mode after boot. Polled mode could be
relegated completely to a legacy role if we could enable interrupts
during boot. Polled mode can be forced after boot by setting
debug.acpi.ec.polled="1", i.e. if there are timeouts.
- Use polling only during boot, shutdown, or if requested by the user.
Otherwise, use a generation count of GPEs, incremented atomically. This
prevents an old status value from being used if the EC is really slow
and the same condition (i.e. multiple IBEs for a write transaction) is
being checked.
- Check for and run the query handler directly if the SCI bit is set in
the status register during boot. Previously, the query handler wouldn't
run until interrupts were finally enabled late in boot.
- During boot and after starting a command, check if the event appears
to already have occurred before we even start waiting. If so, it's
possible the EC is very slow and we might accept an old status value.
Print a warning in this case. Once we've booted, interrupt-driven mode
should work just fine but polled mode could be unreliable. There's not
much more we can do about this until interrupts are enabled during boot.
- In the above case, we also do one final check if the interrupt-driven
mode gets a timeout. If the status is complete, it will force the
system back into polled mode since interrupt mode doesn't work. For
polled mode during boot, if the status appears to be already complete
before beginning the check loop, it waits 10 us before actually checking
the status, just in case the EC is really slow and hasn't gotten to work
on the new request yet.
- Use upper-case hex for the _Qxx method
- Use device_printf for errors, don't hide them under verbose
- Increase default total timeout to 750 ms and decrease polling interval
to 5 us.
- Don't pass the status value via the softc. Just read it directly.
- Remove the mutex. We use the sx lock for transaction serialization
with the query handler.
- Remove the Intel copyright notice as no code of theirs was ever
present in this file (verified against rev 1.1)
- Allow KTR module-only builds for ease of testing
Thanks to jkim and Alexey Starikovskiy for helpful discussions and testing.
Approved by: re
MFC after: 2 weeks
- The output routine of low level console is not protected by any lock
by default.
- Increment and decrement of sc->write_in_progress are not atomic and
this may cause console hang.
- We also have many other states used by emulator that should be protected
by the lock.
- This change does not fix interspersed messages which PRINTF_BUFR_SIZE
kernel option should fix.
Approved by: re (bmah)
MFC after: 1 week
controller if it's sole child device has the "usb" device class.
Previously ehci(4) would think that PCI-ISA bridges on the same slot
(such as in some Intel ICHs) were "neighbors" resulting in spurious
warnings about neighbor count mismatches.
- Fix a memory leak when looking for neighbors.
MFC after: 1 week
Approved by: re (kensmith)
Tested by: phk
to become unkillable when that process is sent a termination signal. The
process will sit in waitvt looping in the kernel, and chewing up all
available CPU until the system is rebooted.
Submitted by: Jilles Tjoelker <jilles@stack.nl>
Reviewed by: bde
Approved by: re (kensmith)
MFC after: 1 week
the mfi(4) LSI MegaSAS RAID card. Looking at the Linux driver for the
mpt(4) it should be 0x0062 and not 0x0060. Tested with an mfi card
of this device id.
Approved by: re (bmah)
Reviewed by: scottl
MFC after: 3 days
o add driver callback to handle notification of beacon changes;
this is required for devices that manage beacon frames themselves
(devices must override the default handler which does nothing)
o move beacon update-related flags from ieee80211com to the beacon
offsets storage (or handle however a driver wants)
o expand beacon offsets structure with members needed for 11h/dfs
and appie's
o change calling convention for ieee80211_beacon_alloc and
ieee80211_beacon_update
o add overlapping bss support for 11g; requires driver to pass
beacon frames from overlapping bss up to net80211 which is not
presently done by any driver
o move HT beacon contents update to a routine in the HT code area
Reviewed by: avatar, thompsa, sephe
Approved by: re (blanket wireless)
does not have a rate table in older hal's so if we scan such a
channel the driver will hit an assertion or crash; for old hal's
fallback to using the static turbo rate table for this mode
(not correct but good enough for now given none of the rate
control algorithms understand how to switch between base+boost)
Approved by: re (blanket wireless)
mode works properly, previously the hostap channel could not be changed off #3.
Fix an ifp/sc misuse while I am here.
Reported by: many
Approved by: re (bmah)
change interrupt if the link is established with link parter. However
interrupt handler didn't acknowledge the interrupt if nfe(4) was not
running at the time of interrupt delivery. This caused endless
interrupt generation. Fix the bug by acknowledging the interrupt
regardless of running state of the driver.
PR: kern/116295
Submitted by: Mark Derbyshire (mark At taom dot com)
Approved by: re (kensmith)
other changes too).
(without any real order)
1. Use device_get_nameunit for mutex naming
2. Add timer for low-latency playback
3. Move most mixer controls from sysctls to mixer(8) controls.
This is a largest part of this patch.
4. Add analog/digital switch (as a temporary sysctl)
5. Get back support for low-bitrate playback (with help of (2))
6. Change locking for exclusive I/O. Writing to non-PTR register
is almost safe and does not need to be ordered with PTR operations.
7. Disable MIDI until we get it to detach properly and fix memory
managment problems.
8. Enable multichannel playback by default. It is as stable as
single-channel mode. Multichannel recording is still an
experimental feature.
9. Multichannel options can be changed by loader tunables.
10. Add a way to disable card from a loader tunable.
11. Add new PCI IDs.
12. Debugger settings are loader tunables now.
14. Remove some unused variables.
15. Mark pcm sub-devices MPSAFE.
16. Partially revert (bus_setup_intr -> snd_setup_intr) since it need
to be done independently
Submitted by: Yuriy Tsibizov (driver maintainer)
Approved by: re (bmah)
- duplicate #define in header, thanks to Kevin Lo for pointing out.
- incorrect BUSMASTER enable logic, thanks Patrick Oeschger
- 82543 fails due to bogus IO BAR logic
- Allow 82571 to use MSI interrupts
- Checksum Offload for UDP not working on 82575
Approved by:re
ioctl().
Note that other information provided by ifconfig(8) such like "list chan"
or "list ap" are still not available at this moment.
Before an(4) is connected to wlan(4), users are encouraged to use
ancontrol(8) to retrieve aforementioned information.
Reported by: dhw (http://lists.freebsd.org/pipermail/freebsd-current/2007-July/074848.html)
Reviewed by: ambrisko
Tested by: dhw
Approved by: re (bmah)
- fix the use after free seen when sending packets small enough to fit as an immediate
and bpf peers are present
- update to firmware rev 4.7 along with various small vendor fixes
Supported by: Chelsio
Approved by: re (blanket)
MFC after: 3 days
that can lead to a panic when the stick is yanked.
- make sure that zyd_attach() returns 0 or errno.
Submitted by: Weongyo Jeong <weongyo.jeong@gmail.com>
Reported by: Ted Lindgreen <ted@tednet.nl>
Reviewed by: sam
Approved by: re (blanket wireless)
o update ic_lastdata to reflect time of last outbound frame
o outbound traffic must preempt/cancel bg scanning to avoid delays
This stuff was somehow missed in the initial import.
Reviewed by: thompsa, avatar, sephe (earlier version)
Approved by: re (blanket wireless)
The first drop was Beta, this code is expected to be the release version.
Note that this driver code will build in either 6.2 or 7. If you
use the code in 6.2 you will not get TSO or MSI/X support but it will
function in a legacy mode.
Approved by: re
needed at least to convince the BIOS to give us access to CPU freq
control on MacBooks.
Submitted by: Rui Paulo <rpaulo / fnop.net>
Approved by: re
MFC after: 5 days
ZD1211/ZD1211B USB IEEE 802.11b/g wireless network devices. Not (yet)
connected to the build process (next batch of commits once I've looped
the current back back).
Submitted by: Weongyo Jeong
Reviewed by: sam@
Approved by: re@
Both WWNN and WWPN are 64-bit unsigned integers and they are prefixed
with "0x", which requires two more bytes each.
Submitted by: Danny Braniss (danny at cs dot huji dot ac dot il)
via Matthew Jacob (lydianconcepts at gmail dot com)
Approved by: re (bmah)
MFC after: 3 days
- remove cpl->iff panic - we can't know the port number from the rspq on the 4-port
- pick the ifnet based on the interface in the CPL header
- switch to using qset 0 for egress on the 4-port for now - may change
when we start using RSS
- move ether_ifdetach to before the port lock gets deinitialized to avoid
hang in the case where there are BPF peers (cxgb_ioctl is called indirectly
when BPF peers are present)
- don't call t3_mac_reset if multiport is set, this was causing tx errors
by misconfiguring the MAC on the 4-port
- change V_TXPKT_INTF to use txpkt_intf as the interfaces are not contiguous
- free the mbuf immediately in the case where the payload is small enough to be copied
into the rspq
- only update the coalesce timer if for a queue if packets were taken off of it
- add in missed 20ms DELAY in initializaton vsc8211
- prompt MFC as this only applies to the 4-port which is currently completely
broken - OK'd by kensmith
Supported by: Chelsio
Approved by: re (blanket)
MFC after: 0 days
on an down mxge interface
- Fix a bug where mxge reported the link state as
active when it wasn't (after ifconfig down).
- Prevent spurious watchdog resets when link partner is not consuming
- Add support for CX4 and popular XFP media detection
- Update the firmware and associated header files to 1.4.25
Approved by: re (kensmith)
and newer CPUs (including Core 2 and Core / Core 2 based Xeons). The
driver attaches to each cpu device and creates a sysctl node in that
device's sysctl context (dev.cpu.N.temperature). When invoked, the
handler binds to the appropriate CPU to ensure a correct reading.
Submitted by: Rui Paulo <rpaulo@fnop.net>
Sponsored by: Google Summer of Code 2007
Tested by: des, marcus, Constantine A. Murenin, Ian FREISLICH
Approved by: re (kensmith)
MFC after: 3 weeks
Without this the PHY wouldn't work as expected. This should fix
dual-boot Windows XP machine where RealTek Windows drivers put the
PHY in power down mode during shutdown. The magic PHY register
accesses come from RealTek driver. No datasheets mention the magic
PHY registers.
In general, the PHY wakeup code should go into PHY driver. However it
seems that it only apply to RTL8169S single chip and it would be
another hack if we have rgephy(4) check what parent driver/chip model
is attached.
Reported by: lofi, Laurens Timmermans ( laurens AT timkapel DOT nl )
Tested by: lofi
Obtained from: RealTek FreeBSD driver
Approved by: re (Ken Smith)
- Don't leak the config lock if detach() fails due to the controller char
dev being open.
- Close a race between detach() and a process opening the controller char
dev.
MFC after: 1 week
Approved by: re (bmah)
Fix a resource allocation bug (explained by jhb on -acpi)
Thanks for Mike Tancsa for testing and helping track down the bug.
Approved by: re (kensmith)
MFC after: 3 weeks
detailed status on each of the backing subdisks. This allows userland
to see which subdisks are online, failed, missing, or a hot spare.
MFC after: 1 week
Approved by: re (bmah)
Reviewed by: sos
differ in their details with calls to a new function, ehci_hcreset(),
that performs the reset.
The original sequences either had no delay or a 1ms delay between
telling the controller to stop and asserting the controller reset
bit. One instance of the original reset sequence waited for the
controller to indicate that its reset was complete before continuing,
but the other two immediately let the subsequent code execute. The
latter is a problem on some hardware, because a read of the HCCPARAMS
register returns an incorrect value while the reset is in progress,
which triggers an infinite loop in ehci_pci_givecontroller(), which
hangs the system on shutdown.
The reset sequence in ehci_hcreset() starts with the most complete
instance from the original code, which contains a loop to wait for
the controller to indicate that its reset is complete. This appears
to be the correct thing to do according to "Enhanced Host Controller
Interface Specification for Universal Serial Bus" revision 1.0,
section 2.3.1. Add another loop to wait for the controller to
indicate that it has stopped before setting the HCRESET bit. This
is required by the section 2.3.1 in the specification, which says
that setting HCRESET before the controller has halted "will result
in undefined behaviour".
Reviewed by: imp (previous patch version without the extra wait loop)
Tested by: se (previous patch version without the extra wait loop)
Approved by: re (bmah)
MFC after: 1 week
previously conditionally acquired Giant based on debug.mpsafenet. As that
has now been removed, they are no longer required. Removing them
significantly simplifies error-handling in the socket layer, eliminated
quite a bit of unwinding of locking in error cases.
While here clean up the now unneeded opt_net.h, which previously was used
for the NET_WITH_GIANT kernel option. Clean up some related gotos for
consistency.
Reviewed by: bz, csjp
Tested by: kris
Approved by: re (kensmith)
requiring DC_TX_ALIGN or DC_TX_COALESCE, which was previously done
in dc_start_locked(), into dc_encap().
o In dc_encap():
- If m_defrag() fails just drop the packet like other NIC drivers
do. This should only happen when there's a mbuf shortage, in which
case it was possible to end up with an IFQ full of packets which
couldn't be processed as they couldn't be defragmented as they
were taking up all the mbufs themselves. This includes adjusting
dc_start_locked() to not trying to prepend the mbuf (chain) if
dc_encap() has freed it.
- Likewise, if bus_dmamap_load_mbuf() fails as dc_dma_map_txbuf()
failed, free the mbuf possibly allocated by the above call to
m_defrag() and drop the packet.
o In dc_txeof():
- Don't clear IFF_DRV_OACTIVE unless there are at least 6 free TX
descriptors. Further down the road dc_encap() will bail if there
are only 5 or fewer free TX descriptors, causing dc_start_locked()
to abort and prepend the dequeued mbuf again so it makes no sense
to pretend we could process mbufs again when in fact we won't.
While at it replace this magic 5 with a macro DC_TX_LIST_RSVD.
- Just always assign idx to sc->dc_cdata.dc_tx_cons; it doesn't
make much sense to exclude the idx == sc->dc_cdata.dc_tx_cons
case.
o In dc_dma_map_txbuf() there's no need to set sc->dc_cdata.dc_tx_err
to error if the latter is != 0, bus_dmamap_load_mbuf() already
returns the same error value in that case anyway.
o For less overhead, convert to use bus_dmamap_load_mbuf_sg() for
loading RX buffers.
o Remove some banal and/or outdated comments.
Approved by: re (kensmith)
MFC after: 1 week
to clear RL_TDESC_VLANCTL_TAG). This fixes sending packets in the
native VLAN when running both tagged and an untagged VLAN over the
same trunk and descriptors are recycled.
Approved by: re (kensmith)
MFC after: 1 week
that could cause panics and corruption under moderate load. Many thanks
to Matt Reimer, Tom McDonald, and the rest of the guys at VPOP.net for
their help in identifying and testing this.
Approved by: re
errors (especially when jumbo frames are enabled or in low memory systems)
because the RX chain was corrupted when an mbuf was mapped to an unexpected
number of buffers.
- Fixed a problem that would cause kernel panics when an excessively
fragmented TX mbuf couldn't be defragmented and was released by
bce_tx_encap().
Approved by: re(hrs)
MFC after: 7 days
the fast or safe/slow method is in use. Fast remains at 1000, slow is
now at 850 (always preferred to TSC). Since the HPET has proven slower
than ACPI-fast on some systems, drop its quality to 900. In the future,
it is hoped that HPET performance will improve as it is the main
timer Intel supports. HPET may move back to 2000 in -current once RELENG_7
is branched to ensure that it gets tested.
Approved by: re
the duration of the function. The device we would otherwise
have left in an useless state may just as well be the low-level
console. When booting verbose, we do need it addressable if we
want to avoid a MCA.
Approved by: re (kensmith)
framework for non-MPSAFE network protocols:
- Remove debug_mpsafenet variable, sysctl, and tunable.
- Remove NET_NEEDS_GIANT() and associate SYSINITSs used by it to force
debug.mpsafenet=0 if non-MPSAFE protocols are compiled into the kernel.
- Remove logic to automatically flag interrupt handlers as non-MPSAFE if
debug.mpsafenet is set for an INTR_TYPE_NET handler.
- Remove logic to automatically flag netisr handlers as non-MPSAFE if
debug.mpsafenet is set.
- Remove references in a few subsystems, including NFS and Cronyx drivers,
which keyed off debug_mpsafenet to determine various aspects of their own
locking behavior.
- Convert NET_LOCK_GIANT(), NET_UNLOCK_GIANT(), and NET_ASSERT_GIANT into
no-op's, as their entire behavior was determined by the value in
debug_mpsafenet.
- Alias NET_CALLOUT_MPSAFE to CALLOUT_MPSAFE.
Many remaining references to NET_.*_GIANT() and NET_CALLOUT_MPSAFE are still
present in subsystems, and will be removed in followup commits.
Reviewed by: bz, jhb
Approved by: re (kensmith)
- make NDIS_DEBUG a sysctl
- default to IEEE80211_MODE_11B if the card doesnt tell us the channels
- dont mess with ic_des_chan when we assosciate
- Allow a directed scan by setting the ESSID before scanning (verified
with wireshark). Hidden APs probably wouldnt have worked before.
- Grab the channel type and use it to look up the correct curchan for
the scan results (mistakenly used 11B before)
- Fix memory leak in the ndis_scan_results
Tested by: matteo
Reviewed by: sam
Approved by: re (rwatson)
to repeat if you had more than two keys down at any given time (which
happened to me all the time with emacs).
This is taken from PR 110681, although what URATAN Shigenobu describes
there is different than the pathology that I have been seeing. I'm
seeing this only in X, while he sees it on his console, yet I think
the two problems are related. I've also reworked the patch slightly
to conform to the coding standards of adjacent code.
It is unclear to me if this merely masks the maddening bug that I have
seen, or if this is a real fix. I typically see the problem when I'm
typing fast in emacs and using lots of motion keys (meta and control).
In either case, my workstation at work again is finally useful with
this patch.
PR: 110681
Submitted by: URATAN Shigenobu
Approved by: re (blanket)
the protocol to be report on each open, but ignore any errors as set
protocol for mice that don't implement the boot protocol can generate
an error. Evidentally, the Gyration GyroPoint RF Technology Receiver
(Gyration Ultra Cordless) device has this problem.
Submitted by: Eugene M. Kim
PR: 106565
Approved by: re (blanket)
included man pages on how to use it. This code is still somewhat experimental
but has been successfully tested on a number of targets. Many thanks to
Danny for contributing this.
Approved by: re
Ever since switching to adaptive polling re(4) occasionally spews
watchdog timeouts on systems with MSI capability. This change is
minimal one for supporting MSI and re(4) also needs MSIX support
for RTL8111C in future. Because softc structure of re(4) is shared
with rl(4), rl(4) was touched to use the modified softc.
Reported by: cnst
Tested by: cnst
Approved by: re (kensmith)
Because nfe(4) hardware doesn't support SG on Rx path, supporting
jumbo frame requires very large contiguous kernel memory(i.e. several
mega bytes). In case of lack of contiguous kernel memory that
allocation request may always fail. However nfe(4) can operate on normal
sized MTU frames, so go ahead and just disable jumbo frame support.
While I'm here add a new tunable "hw.nfe.jumbo_disable" to disable
jumbo frame support.
In nfe_poll, make sure to invoke correct Rx handler.
Approved by: re (kensmith)
advancing. Read from the timer before attaching to be sure it advances
in 1 us. Since the slowest rate allowed by the spec is 10 MHz, the
timer is guaranteed to change in this interval if it is working.
Tested by: Rui Paulo
Approved by: re
MFC after: 3 days
4KB pages as i386, data structures that just fit in one page on i386 (and
on 64 bit architectures with 8KB pages) can be distributed over two pages
on amd64. This is a porblem in the case of the Symbios driver, since the
SCRIPTS engine in the SCSI chip operates on physical addresses and needs
physically contiguous memory. Earlier patches used contigmalloc on amd64,
but this version replaces part of a structure by a pointer to that data.
In order to not introduce an extra indirection for other architectures,
the change has been made conditional on __amd64__.
Earlier attempts to repair this problem are removed (i.e. the macros that
made amd64 use contigmalloc). The fix was submitted by Jan Mikkelsen and
modified by me to only affect amd64.
PR: 89550
Submitted by: janm at transactionware dot com (Jan Mikkelsen)
Approved by: re (Hiroki Sato)
MFC after: 2 weeks
interrupt that is shared with other devices(e.g. USB) in system and
provide a new tunable "hw.msk.legacy_intr" to activate the legacy
interrupt handler. Setting the tunable automatically disables MSI
for msk(4). Previously msk(4) used adoptive polling with taskqueue(9)
as all msk(4) hardwares I know supports MSI. However, there are cases
that MSI couldn't be used on some hardwares due to bugs in MSI
implementatins.
Tested by: Li-Lun Wang < llwang AT infor DOT org >
Approved by: re (kensmith)
- Add custom .c wrappers for the firmware, rather than the standard
firmware(9) generated firmware objects to work around toolchain
problems on ia64 involving linking objects produced by
ld -b -binary into the kernel.
- Move from using Myricom's ".dat" firmware blobs to using Myricom's
zlib compressed ".h" firmware header files. This is done to
facilitate the custom wrappers, and saves a fair amount of wired
memory in the case where the firmware is built in, or preloaded.
- Fix two compile issues in mxge which only appear on non-i386/amd64.
Reviewed by: mlaier, mav (earlier version with just zlib support)
Glanced at by: sam
Approved by: re (kensmith)
config info. from device.hints. Some machines have ipmi controllers
that do not have attachment info in either PCI, SMBIOS or ACPI.
This idea was hacked together by me and then done properly by
jhb.
Submitted by: jhb
Reviewed by: jhb (man page)
Approved by: re (Ken Smith)
MFC after: 1 week
- Keep last transaction label for each destination.
- If the next label is not free, just give up.
- This should reduce CPU load for TX on if_fwip under heavy load.
Approved by: re (hrs)
This adds a function to agp.c to set the aperture resource ID if it's
not the usual AGP_APBASE. Previously, agp.c had been assuming
AGP_APBASE, which resulted in incorrect agp_info, and contortions by
agp_i810.c to work around it.
This also adds functions to agp.c for default AGP_GET_APERTURE() and
AGP_SET_APERTURE(), which return the aperture resource size and disallow
aperture size changes. Moving to these for our AGP drivers will likely
result in stability improvements. This should fix 855-class aperture
size detection.
Additionally, refuse to attach agp_i810 when some RAM is above 4GB and
the GART can't reference memory that high. This should be very rare.
The correct solution would be bus_dma conversion for agp, which is
beyond the scope of this change. Other AGP drivers could likely use
this change as well.
G33/Q35/Q33 AGP support is also included, but disconnected by default
due to lack of testing.
PR: kern/109724 (855 aperture issue)
Submitted by: FUJIMOTO Kou<fujimoto@j.dendai.ac.jp>
Approved by: re (hrs)
- change include style so build in kernel try OR standalone work.
- Limit HWCSUM - I was led to believe that it would work with RSS,
but our testing had odd issues which suggests this is false.
- A fatfinger error in the ioctl code made ifconfig up not work.
Approved by: re
than indirecting through ifaddr_byindex, which makes things easier with
respect to virtualized network stacks.
Submitted by: Marko Zec <zec at icir dot org>
Reviewed by: Leonid Grossman <Leonid dot Grossman at neterion dot com>
Approved by: re (kensmith)
non-sleepable lock held. drm_pci_alloc() calls them, thus drm mutex shall
not be held during the call.
Move the drm_pci_alloc() to the start of the i915_initialize() and drop the
the drm mutex around it.
Reported by: Ganbold <ganbold micom mng net>
Reviewed by: anholt
Approved by: re (hrs)
MFC after: 1 week
- use net80211 for scanning and pass the results back to the scan cache
- use ieee80211_init_channels to fill our channel list
- fix up state transitions
- depreciate the old wicontrol ioctls
- add some debugging lines (#define NDIS_DEBUG)
Reviewed by: sam
Approved by: re (kensmith)
ioctls can be removed. These have been #ifdef'd out and left as a reference in
case any of the RIDs need to be turned into sysctls at a later date.
Reviewed by: sam, avatar
Approved by: re (kensmith)
- reduce cpu usage by as much as 25% (40% -> 30) by doing txq reclaim more efficiently
- use mtx_trylock when trying to grab the lock to avoid spinning during long encap loop
- add per-txq reclaim task
- if mbufs were successfully re-claimed try another pass
- track txq overruns with sysctl
Approved by: re (blanket)
- Add controller id for Intel 82801I (ICH9).
PR: kern/114399
Submitted by: Michael Fuckner <michael@fuckner.net>
- MSI support. Disable by default due to various issues with too many
broken hardwares. MSI can be enabled through device.hints(5) or
kenv(8) by setting "hint.pcm.%d.msi=1".
Partially submitted by: kevlo
YAMAMOTO Taku <taku@tackymt.homeip.net>
Tested by: joel, kevlo, YAMAMOTO Taku
Approved by: re (hrs)
MFC after: 3 days
do the heavy lifting of the 'mii_tick' function, rue was left behind.
Implement this in a naive way. Reports from the field show this makes
the driver functional with some locking issues, as opposed to an
instant panic. Those will be addressed in a later version of the
driver.
Approved by: re@ (bmah)
Sort NETGEAR list per convention.
Swap QUALCOMM and QUALCOMM2.
Add a few vendor products.
no md5 changes with this file (except when USBVERBOSE is enabled)
Approved by: re@ (blanket)
- Handle directories and leaves other than unit directories and text leaves
correctly.
- Now we can retrieve CROM of iSight correctly.
Approved by: re (hrs)
Tested by: flz
MFC after: 3 days
in. These are exclusively in the name of the company for this round.
No new devices have been added, but the MITEL entry has been
eliminated because nothing uses it. You won't see any difference
unless you have USBVERBOSE defined for the kernel.
Approved by: re@ (blanket)
nxge: cast page size fragments down to (int). If the vm's demand paging
PAGE_SIZE is ever too big for that, we've got far bigger problems.
ofw: move va_start() a little earlier. gcc-4.2 doesn't like us modifying
the last arg before the va_start().
Approved by: re (rwatson)
would be 93C46(1Kbit) or 93C56(2Kbit). One of differences between them
is number of address lines required to access the EEPROM. For example,
93C56 EEPROM needs 8 address lines to read/write data. If 93C56
recevied premature end of required number of serial clock(CLK) to set
OP code/address of EEPROM, the result would be unexpected behavior.
Previously it tried to detect 93C46, which requires 6 address lines,
and then assumed it would be 93C56 if read data was not expected
value. However, this approach didn't work in some models/situations
as 93C56 requries 8 address lines to access its data. In order to fix
it, change EEPROM probing order such that 93C56 is detected reliably.
While I'm here change hard-coded address line numbers with defined
constant to enhance readability.
PR: 112710
Approved by: re (mux)
o Adonics Cable 205
o Aiptek PocketCAM 3Mega
o Belkin USB2SCSI
o Casio QV DigiCam
o CCYU EasyDisk ED1064
o Desknote UCR-61S2B
o Epson Stylus Photo 875DC Card Reader
o Epson Stylus Photo 895 Card Reader
o Feiya 5-in-1 Card Reader
o Hitachi Dvd-CAM DZ-MV100A Camcorder
o HP CD-WRiter+ CD-4e
o Insystem Storage Adapter v2
o Kyocera Finecam S3x
o Kyocera Finecam S4
o Kyocera Finecam S5
o Kyocera Finecam L3
o Lexar USB CF Reader
o MindAtWork Digital Wallet
o Minolta Dimage F300
o Minolta Dimage E223
o Minsumi USB Fdd
o Netac USB-CF-Card
o NetChip USB Clik! 40
o Onspec MDCFE-B USB CF Reader
o Onspec SIIG/Datafab Memory Stick + CF Reader/Writer
o Onspec Datafab-based Reader
o Onspec PNY/Datafab CF+SM Reader
o Onspec SimpleTech/Datafab CF+SM Reader
o Onspec MDSM-b Reader
o Onspec USB To CF + SM Combo (LC1)
o Onspec ImageMate SDDR55
o Panasonic LS-120 Camera
o Samsung Techwin Digimax 410
o Shuttle eUSB SmartMedia / CompactFlash Adapter
o Skanhex MD 7425 Camera
o Skanhex SX 520z Camera
o Sony Memorystick NW-MS7
o Sony Portable USB Hardrive V2
o Sony Memorystick PEG N760c
o Sony Memorystick MSC-U03
o TREK/IBM USB memory key
o Trumpion T33520 USB Flash Card Controller
o Trumpion MP3 Player
o Vivtar Vivicam 35Xx
o WinMaxGroup USB Flash Disk 64M-C
o Zoran Digital Camera EX-20 DSC
and maybe a few others...
Submitted by: Vaidas Damosevicius and flz
PR: 79893
Reviewed by: njl, flz
Approved by: re (blanket)
that should be a no-op (for example, requesting SYNC on record path).
The standards does not indicate that such requests are illegal, so
just return it as success instead of EINVAL.
Approved by: re (mux)
First, we were never correctly checking for a 24XX Status Type 0
response- that cased us to fall through to evaluate status for
commands as if this were a 2100/2200/2300 Status Type 0 response.
This is *close*, but not quite the same. This has been reported
to be apparent with some wierd lun configuration problems with
some arrays. It became glaringly apparent on sparc64 where none
of the correct byte swap things were done.
Fixing this omission then caused a whole universe shifting debug
cycle of endian issues for the 2400. The manual for 24XX f/w turns
out to be wrong about the endianness of a couple of entities. The
lun and cdb fields for the type 7 request are *not* unconditionally
big endian- they happen to be opposite of whatever the endian of
the current machine type is. Same with the sense data for the
24XX type 0 response.
While we're at it investigate and resolve some NVRAM endian
issues.
Approved by: re (ken)
MFC after: 3 days
Submitted by: Simon Schubert <corecode@fs.ei.tum.de>
- Defer flushing unsolicited response into taskqueue thread rather
than handle it directly in interrupt handler, since few of its
operations (like measuring/calibrating jack impedance) are quite
expensive.
- Misc. debugging cleanups.
Tested by: joel
Approved by: re (hrs)
MFC after: 3 days
Note: The offending quirk should have been made model/codec specific,
but since there were no records / log which model requires it, the quirk
logic had to be inverted (blacklist instead of whitelist).
Tested by: Arkadiy Dudevitch <dudevitch@englerllc.com>
Approved by: re (hrs)
MFC after: 3 days
