Initialize the execfile argument to NULL instead of _PATH_DEVNULL. This allows
the -M option to be used without specifying -N.
PR: bin/138146
Approved by: rrs (mentor)
Placate new binutils, by using 16-bit %ax instead of 32-bit %eax as an
argument for fnstsw. Explicitely specify sizes for the XMM control and
status word and X87 control and status words.
Install the padlock(4) man page on amd64 as well as i386, to match the
platforms where the driver itself is compiled and installed.
PR: docs/130895
Reported by: George Hartzell <hartzell alerce.com>
Implement an "-x" option to cp(1), for compatibility with Linux and
feature parity with du(1) and similar: When set, cp(1) will not traverse
mount points.
PR: bin/88056
Initial patch by: Graham J Lee leeg teaching.physics.ox.ac.uk
Introduce new rc.conf variable firewall_coscripts. It can be used to
specify list of executables and/or rc scripts that should be executed
after firewall starts/stops.
Submitted by: Yuri Kurenkov <y dot kurenkov at init dot ru>
Reviewed by: rhodes, rc@
Improve checking whether an ARM VA has a valid mapping before performing cache
sync.
VIPT/PIPT caches need valid VA-PA mapping in PTE for a cache operation to
succeed (unlike VIVT). Prior to this fix pmap was using l2pte_valid() for that
check, but this is not sufficient as the function merely checks if a PTE
exists (there can be existing but _invalid_ entries in the table).
A new pmap_has_valid_mapping() routine is introduced to do this job right by
checking proper PTE flags.
Among other potential problems this cures coherency issues with L2 caches on
MV-78100.
Submitted by: Grzegorz Bernacki, Piotr Ziecik
Reviewed, tested by: marcel
Obtained from: Semihalf
Add FIS-based switching support. If controller supports FBS, it allows
several devices beyond Port Multiplier to work simultaneously, substantially
increasing performance.
Add Power Up In Stand-by feature support. Device with PUIS enabled
require explicit command to do initial spin-up. Mark that command
with CAM_HIGH_POWER flag, to allow CAM manage staggered spin-up.
- Use separate buffer for identify data fetching. We can't use main buffer
here if device already running, as data need to be formatted before use.
- Remove some saved_ccb variables. They are unused now.
- Give ATA/SATA SIMs info about ATAPI packet size, supported by device.
- Make ATA XPT to reject longer SCSI CDBs then supported by device, or
any SCSI CDBs, if device doesn't support ATAPI.
Large set of CAM improvements:
- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
Add support for SATA part of Marvell 88SE912x controllers to ahci(4).
Limit early revisions from 6Gb/s to 3Gb/s by default, or they negotiate
only 1.5Gb/s, when 3Gb/s devices connected.
Add dummy driver for PATA part of these controllers, preventing generic
driver attach them. It causes system freeze when SATA controller used after
PATA was touched.
Make ata_getrev() an optional method by implementing ata_null_getrev().
This fixes a bogus '???' boot message on Cambria boards with a CompactFlash
card.
Make OSS_GETVERSION ioctl really work. It has 'M' group, not 'P',
as different nearby ones, and was grabbed by MIXER_xxx() handler.
While there, replace '(cmd & MIXER_xxx(0)) == MIXER_xxx(0)' expressions
with more correct '(cmd & ~0xff) == MIXER_xxx(0)'. Use of bit operations
to compare numeric fields doesn't looks sane.
Implement the "-i" option to sysctl(8), to ignore failures while
retrieving individual OIDs. This allows the same list of OIDs to be
passed to sysctl(8) across different systems where particular OIDs may
not exist, and still get as much information as possible from them.
PR: bin/123644
Submitted by: dhw
Don't panic on failure to attach if we fail before or during the
if_alloc() of ifp.
This fixes the panic reported in the PRs, but not the attach failure.
PR: kern/139079, kern/143874
Tested by: Steven Noonan <steven uplinklabs.net>
Reviewed by: thompsa
Patch the experimental NFS client so that there is a timeout
for negative name cache entries in a manner analogous to
r202767 for the regular NFS client. Also, make the code in
nfs_lookup() compatible with that of the regular client
and replace the sysctl variable that enabled negative name
caching with the mount point option.
The multiplicand a = 0x5deece66d = 25214903917, not 0xfdeece66d.
This bug in the man page has gone unnoticed for over 15 years!
PR: docs/143461
Submitted by: Jeremy Huddleston jeremyhu apple.com
