redefine such operations for different consumers.
This will be used when NUMA support will be finished and numaset
will need to be used.
Sponsored by: EMC / Isilon storage division
Obtained from: jeff
Reviewed by: alc
of "right".)
Flip back on the "always continue TX DMA using the holding descriptor"
code - by always setting ATH_BUF_BUSY and never setting axq_link to NULL.
Since the holding descriptor is accessed via txq->axq_link and _that_
is done behind the TXQ lock rather than the TX path lock, the holding
descriptor stuff itself needs to be behind the TXQ lock.
So, do the mental gymnastics needed to do this.
I've not seen any of the hardware failures that I was seeing when
I last tried to do this.
Tested:
* AR5416, STA mode
Until an ADM6996 driver shows up, this allows for the two switch
ports to be used.
Submitted by: Luiz Otavio O Souza <loos.br@gmail.com>
Reviewed by: ray
* Fix API changes;
* remove unused code;
* Allow some switches to be used that don't expose a set of PHY
registers for the CPU facing port (eg the ADM6996 for the Ubiquiti
Routerstation.)
Submitted by: Luiz Otavio O Souza <loos.br@gmail.com>
Reviewed by: ray
This adds a vlan capability field to etherswitch_info structure and some
definitions of ports flags.
It adds the support to global config parameters which right now is used
only to switch between the vlan modes, but it is intended to be extended
to support the setup of others parameters (STP, mirror, etc.).
Submitted by: Luiz Otavio O Souza <loos.br@gmail.com>
Reviewed by: ray
Use if_initbaudrate() to set baudrate.
Add IFCAP_LINKSTATE to if_capabilities.
Submitted by: David C Somayajulu <davidcs@freebsd.org>
Approved by: George Neville-Neil <gnn@freebsd.org>
do drain (flush_workqueue() in Linux terms) but instead returns true if
the work was removed before it is run, or false otherwise.
Simulate this by removing the taskqueue_drain() and return the value
derived from taskqueue_cancel()'s return value.
This would solve a witness warning caused by calling taskqueue_drain()
with a non-sleepable lock held, like:
taskqueue_drain with the following non-sleepable locks held:
exclusive rw lle (lle) r = 0 (0xfffffe001450b410) locked @
/usr/src/sys/netinet/in.c:1484
KDB: stack backtrace:
db_trace_self_wrapper() at db_trace_self_wrapper+0x2b/frame 0xffffff848d4f7690
kdb_backtrace() at kdb_backtrace+0x39/frame 0xffffff848d4f7740
witness_warn() at witness_warn+0x4a8/frame 0xffffff848d4f7800
taskqueue_drain() at taskqueue_drain+0x3a/frame 0xffffff848d4f7840
set_timeout() at set_timeout+0x4a/frame 0xffffff848d4f7860
netevent_callback() at netevent_callback+0x16/frame 0xffffff848d4f7870
arpintr() at arpintr+0x9b5/frame 0xffffff848d4f7930
This do not affect kernel without OFED compiled in.
Reported by: Garrett Cooper <yaneurabeya gmail com>
(who also tested an earlier version of this patch,
but bugs are mine)
MFC after: 2 weeks
I'm not sure why this is failing. The holding descriptor should be being
re-read when starting DMA of the next frame. Obviously something here
isn't totally correct.
I'll review the TX queue handling and see if I can figure out why this
is failing. I'll then re-revert this patch out and use the holding
descriptor again.
2. Added Flash Read/Update Support
3. Fixed TSO Handling
Submitted by: David C Somayajulu (davidcs@freebsd.org)
Reviewed by: George Neville-Neil (gnn@freebsd.org)
Approved by: George Neville-Neil (gnn@freebsd.org)
and printing at boot.
For reference on table informations and purposes please review ACPI specs.
Sponsored by: EMC / Isilon storage division
Obtained from: jeff
Reviewed by: jhb (earlier version)
order to match the MAXCPU concept. The change should also be useful
for consolidation and consistency.
Sponsored by: EMC / Isilon storage division
Obtained from: jeff
Reviewed by: alc
defaults to 1, meaning that it's off.
When read-ahead is enabled on a file, the vfs cluster code deliberately
breaks a read into 2 I/O transactions; one to satisfy the actual read,
and one to perform read-ahead. This makes sense in low-latency
circumstances, but often produces unbalanced i/o transactions that
penalize disks. By setting vfs.read_min, we can tell the algorithm to
fetch a larger transaction that what we asked for, achieving the same
effect as the read-ahead but without the doubled, unbalanced transaction
and the slightly lower latency. This significantly helps our workloads
with video streaming.
Submitted by: emax
Reviewed by: kib
Obtained from: Netflix
but partly to just tidy up things.
The problem here - there are too many TX buffers in the queue! By the
time one needs to transmit an EAPOL frame (for this PR, it's the response
to the group rekey notification from the AP) there are no ath_buf entries
free and the EAPOL frame doesn't go out.
Now, the problem!
* Enforcing the TX buffer limitation _before_ we dequeue the frame?
Bad idea. Because..
* .. it means I can't check whether the mbuf has M_EAPOL set.
The solution(s):
* De-queue the frame first
* Don't bother doing the TX buffer minimum free check until after
we know whether it's an EAPOL frame or not.
* If it's an EAPOL frame, allocate the buffer from the mgmt pool
rather than the default pool.
Whilst I'm here:
* Add a tweak to limit how many buffers a single node can acquire.
* Don't enforce that for EAPOL frames.
* .. set that to default to 1/4 of the available buffers, or 32,
whichever is more sane.
This doesn't fix issues due to a sleeping node or a very poor performing
node; but this doesn't make it worse.
Tested:
* AR5416 STA, TX'ing 100+ mbit UDP to an AP, but only 50mbit being received
(thus the TX queue fills up.)
* .. with CCMP / WPA2 encryption configured
* .. and the group rekey time set to 10 seconds, just to elicit the
behaviour very quickly.
PR: kern/138379
the page. This both reduces the number of queues locking and avoids
moving the active page to inactive list just because the page was read
or written.
Based on the suggestion by: alc
Reviewed by: alc
Tested by: pho
Keep following access permissions:
APX AP Kernel User
1 01 R N
1 10 R R
0 01 R/W N
0 11 R/W R/W
Avoid using reserved in ARMv6 APX|AP settings:
- In case of unprivileged (user) access without permission to write,
the access permission bits were being set to reserved for ARMv6
(but valid for ARMv7) value of APX|AP = 111.
Fix-up faulting userland accesses properly:
- Wrong condition statement in pmap_fault_fixup() caused that
any genuine, unprivileged access was being fixed-up instead of
just skip doing anything and return. Staring from now we ensure
proper reaction for illicit user accesses.
L2_S_PROT_R and L2_S_PROT_U names might be misleading as they do not
reflect real permission levels. It will be clarified in following
patches (switch to AP[2:1] permissions model).
Obtained from: Semihalf
- On ARMADAXP B0 (GP development board) we are not able to use PCI due to
whole 32-bit address space used by 4GB of RAM memory.
- Change is required to destroy unnecessary window to free address space
for PCI and other devices
- Fix offset value for SDRAM decoding windows
Obtained from: Semihalf
to driver specific files.
- window initialization is done during device attach
- CESA TDMA decoding windows values are set based on DTS,
not copied from CPU registers
- remove unnecessary virtual mapping
- update dts file
Obtained from: Semihalf
- Allow DMA addresses anywhere in the lower 4GB; Envy24HT has a 32-bit DMA
engine, not 28-bit like Envy24.
- Mark interrupt handler as MPSAFE, seems to be correctly synchronized.
PR: kern/152378
Submitted by: Jason Harmening <jason.harmening@gmail.com>
MFC after: 1 month
used previously caused probe failure on platforms where char is unsigned
(e.g. ARM), as mftrecsz can be negative.
Submitted by: Ilya Bakulin <ilya@bakulin.de>
MFC after: 2 weeks
change the way that these functions ascend the tree when the search for a
matching leaf fails at an interior node. Rather than returning to the root
of the tree and repeating the lookup with an updated key, maintain a stack
of interior nodes that were visited during the descent and use that stack
to resume the lookup at the closest ancestor that might have a matching
descendant.
Sponsored by: EMC / Isilon Storage Division
Reviewed by: attilio
Tested by: pho
fork_trampoline (thread entry point) assembler routines, because it's
not possible to unwind beyond those points.
Also insert STOP_UNWINDING in the exception_exit routine, to prevent an
unwind-loop at that point. This is just a stopgap until we get around
to instrumenting all assembler functions with proper unwind metadata.
exit the loop until after printing info about the current frame. Also,
if executing the unwind function for a frame doesn't change the values of
any registers, log that and exit the loop rather than looping endlessly.
