The newer hardware revisions of the Raspberry Pi 4 removed the ability of
the VIA VL805 xhci controller to load its own firmware. Instead the
firmware must be installed at the appropriate time by the VideoCore
coprocessor.
Submitted by: Robert Crowston <crowston_protonmail.com>
Differential Revision: https://reviews.freebsd.org/D25261
Handle the fact that parts of usb(4) can be compiled into the boot
loader, where M_WAITOK does not guarantee a successful allocation.
PR: 240545
Submitted by: Andrew Reiter <arr@watson.org> (original version)
Reviewed by: hselasky
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D25706
Create an acpi attachment for the DWC USB OTG device. This is present in
the Raspberry Pi 4 in the USB-C port normally used to power the board. Some
firmware presents the kernel with ACPI tables rather than FDT so we need
an ACPI attachment.
Submitted by: Greg V <greg_unrelenting.technology>
Approved by: hselasky (removal of All rights reserved)
Differential Revision: https://reviews.freebsd.org/D25203
description of items residing in a so-called union. FreeBSD currently
only supports 4 such pop levels.
If the push level is not restored within the processing of the same
HID item, an invalid memory location may be used for subsequent HID
item processing.
Verify that the push level is always valid when processing HID items.
Reported by: Andy Nguyen (Google)
MFC after: 3 days
Sponsored by: Mellanox Technologies
This specifically fixes that TX frames are large enough now to hold a 3900 odd
byte AMSDU (the little ones); me flipping it on earlier messed up transmit!
Tested:
* if_run, STA mode, TX/RX TCP/UDP iperf. TCP is now back to normal and
correctly does ~ 3200 byte AMSDU/fast frames (2x1600ish byte MSDUs).
* Set the tx/rx chains based on the existing MIMO eeprom reads
* Add 3-chain rates
Tested:
* MAC/BBP RT5390 (rev 0x0502), RF RT5370 (MIMO 1T1R), 2g/5g STA
* MAC/BBP RT3593 (rev 0x0402), RF RT3053 (MIMO 3T3R), 2g/5g STA
Now that I'm a proud owner of an ASUS USB-N66, I can test 2G/5G and
3-stream configurations.
For now, just flip on 5G HT rates. I've tested this in both
5G HT20 and 5G 11a modes. It's still one stream for now until
we verify that the number of streams reported (ie the MIMO below)
is actually the number of 11n streams, NOT the number of antennas.
(They don't have to match! You can have more antennas than MIMO
streams!)
Tested:
* run0: MAC/BBP RT3593 (rev 0x0402), RF RT3053 (MIMO 3T3R)
* Enable self-generated 11n frames
* add MCS rates for 1-stream and 2-stream rates; will do 3-stream
once the rest of this tests out OK with other people.
* Hard-code 1 stream for now
* Add A-MPDU RX mbuf tagging
* RTS/CTS if doing RTSCTS in HT protmode as well as legacy; they're
separate configuration flags
* Update the amrr rate index stuff - walk the rates array like others
to find the right one - this now works for MCS and CCK/OFDM rates
* Add support for atheros fast frames/AMSDU support as we can generate
those in net80211.
TODO:
* HT40 isn't enabled yet
* No A-MPDU support just yet; that requires some more firmware research
and maybe porting some ath(4) A-MPDU support/tracking into net80211
* Short preamble flags aren't set yet for MCS; need to check the linux
driver and see what's going on there
* Add 3x3 rates and set tx/rx stream configuration appropriately
* More 5GHz testing; I have a 3x3 dual band USB NIC coming soon that'll
let me test this.
* Figure out why the RX path isn't performing as fast as it could -
there's only a single buffer loaded at a time for the receive path
in the USB bulk handler and this may not be super useful.
Tested:
* RT5390 usb, 1x1, RF5370 (2GHz radio), STA mode - A-MSDU TX, A-MPDU RX
Submitted by: Ashish Gupta <ashishgu@andrew.cmu.edu>
Differential Revision: https://reviews.freebsd.org/D22840
don't implement link power management, LPM.
This fixes error code XHCI_TRB_ERROR_BANDWIDTH for isochronous USB 3.0
transactions.
Submitted by: Horse Ma <Shichun.Ma@dell.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
Name each ehci driver uniquely.
This remove the warning printed at each arm boot :
module_register: cannot register simplebus/ehci from kernel; already loaded from kernel
A similar fix was done in r333074 but imx_ehci wasn't renamed and generic_ehci wasn't
present at that time.
This driver hasn't been relevant in almost 15 years. It was for a product on the
shelves for about 6 months in 2003/2004. I've not updated the driver since then,
and have had nobody talk to me about it since maybe 2006 or 2007. It doesn't
implement a standard interface, and can be better done with libusb. All the
action has moved to webcamd for newer, more fully featured hardware. It makes no
appearances in the nycbug dmesg archive.
Relnotes: yes
MFC After: 3 days
key is pressed at the same time as a regular key, that means key with
modifier is output. Some automated USB keyboards like Yubikeys need this.
This fixes a regression issue after r357861.
Reported by: Adam McDougall <mcdouga9@egr.msu.edu>
PR: 224592
PR: 233884
MFC after: 3 days
Sponsored by: Mellanox Technologies
Skip device mode switch step on Fountain-based devices as they don't
support RAW_SENSOR_MODE command, so failing to attach.
This was reproduced on PowerBook G4 (model PowerBook5,6) equipped with
product ID 0x020e
Reviewed by: hselasky
Approved by: jhibbits (mentor)
Differential Revision: https://reviews.freebsd.org/D24005
maximal input report size instead of wMaxPacketSize.
If the USB frame length is set to 1024 bytes, WMT_BSIZE, the EETI controller
will pack multiple touch events in the packet and the current code will only
process the first touch event.
As a result some important events are lost like releasing the finger from the
touchscreen.
Use the maximal input report size as buffer size instead.
PR: 244718
Tested by: Oskar Holmlund <oskar.holmlund@ohdata.se>, wulf
MFC after: 3 days
Discussed with: hselasky
Limiting frame size to maximum packet size breaks devices which have input
report size larger than wMaxPacketSize. Maximal input report size should be
used instead.
Revert the commit as it have not been MFC-ed yet.
Discussed with: hselasky
will pack multiple touch events in the packet and the current code will only
process the first touch event.
As a result some important events are lost like releasing the finger from the
touchscreen.
Use the maximum maximum packet size as buffer size instead.
Submitted by: Oskar Holmlund <oskar.holmlund@ohdata.se>
PR: 244718
MFC after: 3 days
Sponsored by: Mellanox Technologies
Touch Digitizer V04 report descriptor declares 'Contact Count Maximum' usage
as constant. That was not supported by descriptor parser.
PR: 232040
Reported by: Sergei Akhmatdinov <sakhmatd@darkn.space>
MFC after: 1 week
because it clobbers the super speed link status when a device is in super
speed mode. Currently the power bit is not needed for anything in the USB
hub driver.
This fixes USB warm reset for super speed devices.
Tested by: Shichun.Ma@dell.com
MFC after: 3 days
Sponsored by: Mellanox Technologies
This fixes a regression issue after r357861.
Reported by: James Wright <james.wright@jigsawdezign.com>
PR: 224592
PR: 233884
MFC after: 3 days
Sponsored by: Mellanox Technologies
key-codes from the USB keyboard. Negative key-codes are currently skipped.
While at it use the bit size value provided by the HID location structure
instead of assuming a value of 8.
This fixes a regression issue after r357861.
Reported by: Minoru TANABE <kotanabe3@gmail.com>
PR: 224592
PR: 233884
MFC after: 3 days
Sponsored by: Mellanox Technologies
if_capabilities indicates capabilities supported by the hardware;
if_capenable which are enabled. Note that rx checksum is still disabled
in the driver at compile time.
Submitted by: Johannes <iz-rpi04@hs-karlsruhe.de>
MFC after: 2 weeks
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked). Use it in
preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Reviewed by: hselasky, kib
Approved by: kib (mentor)
Differential Revision: https://reviews.freebsd.org/D23632
Add support for decoding pressed keys as a bitmap. The keys in the
bitmap are described in the interface specific HID descriptor. Some
keyboards even have multiple input interfaces, only using the bitmap
method when the event array is full. That typically means when more
than seven keys are pressed simultaneously.
The internals of the USB keyboard driver have been slightly reworked
to keep track of all keys in a single bitmap having 256 bits. This
bitmap is then divided into blocks of 64-bits as an optimisation.
Simplify automatic key repeat logic, because only the last key pressed
can be repeated.
PR: 224592
PR: 233884
Tested by: Alex V. Petrov <alexvpetrov@gmail.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
This avoids getting the XHCI_TRB_ERROR_CONTEXT_STATE error code from the XHCI
controller when the endpoint is disabled or already stopped.
Suggested by: Shichun.Ma@dell.com
MFC after: 1 week
Sponsored by: Mellanox Technologies
The newer versions of RPi FDT flipped the order of the interrupts
specification and added an 'interrupt-names' property for driver aide in
finding the correct interrupt, rather than assuming the positions. Use it if
it's available, or fallback to the old method if there is no interrupt-names
property with a usb value.
This has been tested with both old RPi3B FDT and new RPi3B FDT, USB again
works on the latter.
Reported by: Tom Yan <tom.ty89 gmail com>
MFC after: 3 days
Do not configure any endpoint twice, but instead keep track of which
endpoints are configured on a per device basis, and use an evaluate
endpoint context command instead. When changing the configuration make
sure all endpoints get deconfigured and the configured endpoint mask
is reset.
This fixes an issue where an endpoint might stop working if there is
an error and the endpoint needs to be reconfigured as a part of the
error recovery mechanism in the FreeBSD USB stack.
Tested by: Shichun.Ma@dell.com
MFC after: 1 week
Sponsored by: Mellanox Technologies
r356087 made it rather innocuous to double-register built-in keyboard
drivers; we now set a flag to indicate that it's been registered and only
act once on a registration anyways. There is no misleading here, as the
follow-up kbd_delete_driver will actually remove the driver as needed now
that the linker set isn't also consulted after kbdinit.
Keyboard drivers are generally registered via linker set. In these cases,
they're also available as kmods which use KPI for registering/unregistering
keyboard drivers outside of the linker set.
For built-in modules, we still fire off MOD_LOAD and maybe even MOD_UNLOAD
if an error occurs, leading to registration via linker set and at MOD_LOAD
time.
This is a minor optimization at best, but it keeps the internal kbd driver
tidy as a future change will merge the linker set driver list into its
internal keyboard_drivers list via SYSINIT and simplify driver lookup by
removing the need to consult the linker set.
Most keyboard drivers are using the genkbd implementations as it is;
formally use them for any that aren't set and make
genkbd_get_fkeystr/genkbd_diag private.
These invocations were directly calling enkbd_diag(), rather than
indirection back through kbdd_diag/kbdsw. While they're functionally
equivent, invoking kbdd_diag where feasible (i.e. not in a diag
implementation) makes it easier to visually identify locking needs in these
other drivers.
The datasheets for these chips claim the maximum is 921,600, but testing
shows these two higher rates also work (but no rates above 921,600 other
than these two work; these represent dividing the base buad clock by 3 and 2
respectively).
o Remove All Rights Reserved from my notices
o imp@FreeBSD.org everywhere
o regularize punctiation, eliminate date ranges
o Make sure that it's clear that I don't claim All Rights reserved by listing
All Rights Reserved on same line as other copyright holders (but not
me). Other such holders are also listed last where it's clear.
Some places in network code may need to verify that an ethernet address
is not the 'zero' address. Provide a standard macro ETHER_IS_ZERO for
this purpose, similar to the ETHER_IS_BROADCAST macro already available.
This patch also removes previous ETHER_IS_ZERO definitions in several
USB ethernet drivers, in favor of this centrally-located macro.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Submitted by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed by: erj@
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D21240
When epoch(9) was introduced to network stack, it was basically
dropped in place of existing locking, which was mutexes and
rwlocks. For the sake of performance mutex covered areas were
as small as possible, so became epoch covered areas.
However, epoch doesn't introduce any contention, it just delays
memory reclaim. So, there is no point to minimise epoch covered
areas in sense of performance. Meanwhile entering/exiting epoch
also has non-zero CPU usage, so doing this less often is a win.
Not the least is also code maintainability. In the new paradigm
we can assume that at any stage of processing a packet, we are
inside network epoch. This makes coding both input and output
path way easier.
On output path we already enter epoch quite early - in the
ip_output(), in the ip6_output().
This patch does the same for the input path. All ISR processing,
network related callouts, other ways of packet injection to the
network stack shall be performed in net_epoch. Any leaf function
that walks network configuration now asserts epoch.
Tricky part is configuration code paths - ioctls, sysctls. They
also call into leaf functions, so some need to be changed.
This patch would introduce more epoch recursions (see EPOCH_TRACE)
than we had before. They will be cleaned up separately, as several
of them aren't trivial. Note, that unlike a lock recursion the
epoch recursion is safe and just wastes a bit of resources.
Reviewed by: gallatin, hselasky, cy, adrian, kristof
Differential Revision: https://reviews.freebsd.org/D19111
Create an attachment file for the existing ACPI attachment, and create a
new FDT attachment for the generic-ehci driver.
Submitted by: andrew (Original version)
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D19389
above 1Kbyte. It might look like some XHCI(4) controllers do not
support when the USB control transfer is split using a link TRB. The
next NORMAL TRB after the link TRB is simply failing with XHCI error
code 4. The quirk ensures we allocate a 64Kbyte buffer so that the
data stage TRB is not broken with a link TRB.
Found at: EuroBSDcon 2019
MFC after: 1 week
Sponsored by: Mellanox Technologies
libusb. This is useful for speeding up large data transfers while reducing
the interrupt rate.
Found at: EuroBSDcon 2019
MFC after: 1 week
Sponsored by: Mellanox Technologies
this to 2k to prevent them from being truncated and ignored. It
appears to be a sanity check only, but bumping it to 2k allows both of
my iic hid devices to be parsed and the second one to work...
After r351243 when ALTQ was enabled in the kernel, the inline functions
in ifq.h would not have full type information as if_var.h was not
included.
Given usb_ethernet.h already includes all the various headers (which)
is the cause of the problem here, add if_var.h to it. This fixes the
builds again.
Reported by: CI system, e.g. FreeBSD-head-aarch64-LINT
order to have struct mii_data available. However, it only really needs
a forward declaration of struct mii_data for use in pointer form for
the return type of a function prototype.
Custom kernel configuration that have usb and fdt enabled, but no miibus,
end up with compilation failures because miibus_if.h will not get
generated.
Due to the above, the following changes have been made to usb_ethernet.h:
* remove the inclusion of mii headers
* forward-declare struct mii_data
* include net/ifq.h to satify the need for complete struct ifqueue
Reviewed by: ian
Obtained from: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D21293
with Communication Device Class Ethernet Emulation Model (CDC EEM).
The driver supports both the device, and host side operation; there
is a new USB template (#11) for the former.
This enables communication with virtual USB NIC provided by iLO 5,
as found in new HPE Proliant servers.
Reviewed by: hselasky
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Hewlett Packard Enterprise
Enable this for the NovAtel OEMv2 GPS receiver.
Not fixed: The receiver shows up as "<Interface 0>" in the device
tree, because that is literally what the descriptor-string is.
Reviewed by: hselasky@
While at it fix an invalid memory access issue when attaching external
USB HUBs, which are not mapped by ACPI, due to missing status check
when calling AcpiGetObjectInfo() from acpi_usb_hub_port_probe_cb().
Sponsored by: Mellanox Technologies
This adds ACPI device path on devinfo(8) output and
show value of _UPC(usb port capabilities), _PLD (physical location of device)
when hw.usb.debug >= 1 .
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D20630
rename the source to gsb_crc32.c.
This is a prerequisite of unifying kernel zlib instances.
PR: 229763
Submitted by: Yoshihiro Ota <ota at j.email.ne.jp>
Differential Revision: https://reviews.freebsd.org/D20193
asserted. Some development boards for example will reset on DTR,
and some radio interfaces will transmit on RTS.
This patch allows "stty -f /dev/ttyu9.init -rtsdtr" to prevent
RTS and DTR from being asserted on open(), allowing these devices
to be used without problems.
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D20031
if a USB transfer is cancelled that we need to fake a completion event.
Implement missing support in ugen_fs_copy_out() to handle this.
This fixes issues with webcamd(8) and firefox.
MFC after: 3 days
Sponsored by: Mellanox Technologies
This is a curious small widget for which I might write a driver.
It is bridge between USB HID interface and I2C interface plus some
GPIO pins.
MFC after: 2 weeks
all-ones then carving out blocks of zeroes where specified values go, init
it to all-zeroes, put in ones where values need to be masked, then use it
as value &= ~sc_led_modes_mask. In addition to being more idiomatic, this
means everything related to FDT data is initialized to zero along with the
rest of the softc, and that allows removing some #ifdef FDT sections and
wrapping the whole muge_set_leds() function in a single ifdef block.
This also deletes the early-out from muge_set_leds() when an eeprom exists.
Even if there is an eeprom with led config in it, the fdt data (if present)
should override that, because the user is in control of the fdt data.
OTP registers (because the user is in control of the fdt data). Remove the
early returns from the code that tries to find a good mac address, so that
the execution always flows through the routine to get an address from FDT
data last, when on FDT-enabled systems.
the device instance, and to get the MAC address for the device instance.
The ad-hoc code this replaces could find the wrong instance if multiple
devices were present.
Also use LED mode settings from the FDT to set the PHY.
From v3 of the patch submitted in the PR.
I moved the sc_led_modes and sc_led_modes_mask default setting outside
of the #ifdef FDT case.
PR: 237325
Submitted by: Ralf <iz-rpi03@hs-karlsruhe.de>
Reviewed by: ian
MFC after: 2 weeks
MFC with: r348001
Event: Waterloo Hackathon 2019
Differential Revision: https://reviews.freebsd.org/D20325
Also apply some style(9) and remove the message about EEPROM configuration
(if there's an EEPROM the hardware handles LED configuration itself).
PR: 237325
Reviewed by: ian
MFC after: 2 weeks
Submitted by: Ralf <iz-rpi03@hs-karlsruhe.de>
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
FDT data is sometimes used to configure usb devices which are hardwired into
an embedded system. Because the devices are instantiated by the usb
enumeration process rather than by ofwbus iterating through the fdt data, it
is somewhat difficult for a usb driver to locate fdt data that belongs to
it. In the past, various ad-hoc methods have been used, which can lead to
errors such applying configuration that should apply only to a hardwired
device onto a similar device attached by the user at runtime. For example,
if the user adds an ethernet device that uses the same driver as the builtin
ethernet, both devices might end up with the same MAC address.
These changes add a new usb_fdt_get_node() helper function that a driver can
use to locate FDT data that belongs to a single unique instance of the
device. This function locates the proper FDT data using the mechanism
detailed in the standard "usb-device.txt" binding document [1].
There is also a new usb_fdt_get_mac_addr() function, used to retrieve the
mac address for a given device instance from the fdt data. It uses
usb_fdt_get_node() to locate the right node in the FDT data, and attempts to
obtain the mac-address or local-mac-address property (in that order, the
same as linux does it).
The existing if_smsc driver is modified to use the new functions, both as an
example and for testing the new functions. Rpi and rpi2 boards use this
driver and provide the mac address via the fdt data.
[1] https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/usb/usb-device.txt
Differential Revision: https://reviews.freebsd.org/D20262
Ampere eMAG systems have XHCI just described in ACPI, not on PCI.
Submitted by: Greg V <greg@unrelenting.technology>
Reviewed by: andrew
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D19986
RTL8152 (chip version URE_CHIP_VER_4C10) doesn't
have hardwired MAC address, in other words, it is all zeros.
This commit fixes it by setting random MAC address
when MAC address is all zeros.
Reviewed by: kevlo
Differential Revision: https://reviews.freebsd.org/D19856
Both linux and u-boot sources for RTL8152 driver has this value.
RTL8152 USB ethernet is used in NanoPI R1 board as second ethernet.
This fixes for me RTL8152 USB ethernet not detected problem after
reboot on NanoPI R1 board.
Both NetBSD and OpenBSD have a wrong value so far.
frame header and data.
This will fix 'Mysterious OLPC stuff' for received frames and wrong
CCMP / TKIP / data decoding for transmitted frames in net/wireshark
dissector.
While here, drop unneeded comment - net80211 handles padding requirements
for Tx & Rx without driver adjustment.
Tested with D-Link DWA-140 rev B3, STA mode.
MFC after: 1 week
Also, pass control frames to the host while in MONITOR mode and / or
when promiscuous mode is enabled.
Tested with Netgear WG111 v3 (RTL8187B), STA / MONITOR modes.
MFC after: 2 weeks
- Alignment issues:
* Add missing __packed attributes + padding across all drivers; in
most places there was an assumption that padding will be always
minimally suitable; in few places - e.g., in urtw(4) / rtwn(4) -
padding was just missing.
* Add __aligned(8) attribute for all Rx radiotap headers since they can
contain 64-bit TSF timestamp; it cannot appear in Tx radiotap headers, so
just drop the attribute here. Refresh ieee80211_radiotap(9) man page
accordingly.
- Since net80211 automatically updates channel frequency / flags in
ieee80211_radiotap_chan_change() drop duplicate setup for these fields
in drivers.
Tested with Netgear WG111 v3 (urtw(4)), STA mode.
MFC after: 2 weeks
Marvell XHCI is in fact generic-xhci, so move the driver and
add the compatible string.
While here, get and enable the phy if the dtb provide one.
The xhci bindings state that phys should be in a 'phys' property but
Marvell DTS uses 'usb-phy', only add support for 'usb-phy' for now.
Sponsored-by: Rubicon Communications, LCC ("Netgate")
This is a "fake" phy that handle regulator, clocks and reset gpio.
Only clock and regulator is supported for now.
Sponsored-by: Rubicon Communications, LCC ("Netgate")
Enforce net80211 rates for control / management / multicast / EAPOL frames
and allow to override rate for unicast frames via ifconfig(8) 'ucastrate'
option; by default it still uses f/w rate adaptation for unicast frames.
MFC after: 1 week
Wrap ieee80211_add_channel_list_2ghz into another function
which supplies default (1-14) channel list to it and drop
its copies from drivers.
Checked with RTL8188EE, country US / JP / KR / UA.
MFC after: 2 weeks
- Check if buffer can contain Rx descriptor before accessing it.
- Verify upper / lower bounds for frame length.
- Do not pass too short frames into ieee80211_find_rxnode().
While here:
- Move cleanup to the function end.
- Reuse IEEE80211_IS_DATA() macro.
MFC after: 1 week
- Discard frames that are bigger than MCLBYTES (to prevent buffer overrun).
- Check buffer length before accessing its contents.
- Fix len <-> dmalen check - the last includes Rx Wireless information
structure size.
- Fix out-of-bounds read during Rx node search for ACK / CTS frames
(monitor mode only).
While here:
- Mark few suspicious places with comments.
- Move common cleanup to the function end.
MFC after: 1 week
Without HID_IGNORE quirk enabled these models appear in the system as a uhid
devices while NUT (Network UPS Tool) expects them to be ugen.
PR: 131521
Submitted by: Naoyuki Tai <ntai@smartfruit.com>, John Bayly <john.bayly@tipstrade.net>
MFC after: 1 week
Extend the vendor class USB audio quirk to cover devices without
the USB audio control descriptor.
PR: 234794
MFC after: 1 week
Sponsored by: Mellanox Technologies
out dead USB HUB devices by implementing an error counter, so that the USB
enumeration thread does not spend all its time reading from non-responding
devices, blocking user-space access in the end.
Tested by: Matthias Apitz <guru@unixarea.de>
MFC after: 1 week
Sponsored by: Mellanox Technologies
transaction translator will return a NAK. Ignore this message and
retry the complete split instead.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Now evdev part of keyboard drivers does not take any locks if corresponding
input/eventN device node is not opened by userland consumers.
Do not assert console lock inside evdev to handle the cases when keyboard
driver is called from some special single-threaded context like shutdown
thread.
the current fixed values, which enables use of rates above 1 Mbps.
Improved the detection of HXD chips, and the status flag handling as
well.
Submitted by: Gabor Simon <gabor.simon75@gmail.com>
PR: 225932
Differential revision: https://reviews.freebsd.org/D16639
MFC after: 1 week
Sponsored by: Mellanox Technologies
translator, when using the DWC OTG USB controller driver. Make sure to re-try
getting the complete split packets until a DATA0 packet is received. Larger
isochronous frames may be split into multiple MDATA packets terminated
by a single DATA0 packet.
PR: 230434
MFC after: 3 days
Approved by: re (gjb)
Sponsored by: Mellanox Technologies
Remove unused and easy to misuse PNP macro parameter
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
Approved by: re (glen)
r337289 has a side effect of reducing usb frame 0 buffer size down to
touch report size. That broke some devices e.g. "Raydium Touch System"
which are capable of generating non-touch frames of bigger length.
Fix it with enlarging frame 0 buffer up to internal wmt(4) buffer size.
Reported by: Roberto Fernandez Cueto <roberfern@gmail.com>
Tested by: Roberto Fernandez Cueto <roberfern@gmail.com>
Approved by: re (gjb)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D16772
I was not aware Warner was making or planning to make forward progress in
this area and have since been informed of that.
It's easy to apply/reapply when churn dies down.
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
Move evdev_ev_kbd_event() helper from evdev to kbd.c as otherwise evdev
unconditionally requires all keyboard and console stuff to be compiled
into the kernel. This dependency happens as evdev_ev_kbd_event() helper
references kbdsw global variable defined in kbd.c through use of
kbdd_ioctl() macro.
While here make all keyboard drivers respect evdev_rcpt_mask while setting
typematic rate and LEDs with evdev interface.
Requested by: Milan Obuch <bsd@dino.sk>
Reviewed by: hselasky, gonzo
Differential Revision: https://reviews.freebsd.org/D16614
Now softc should be retrieved from struct edvev * pointer
with evdev_get_softc() helper.
wmt(4) is a sample of driver that support both KPI.
Reviewed by: hselasky, gonzo
Differential Revision: https://reviews.freebsd.org/D16614
To compile this driver with evdev support enabled, place
following lines into the kernel configuration file:
options EVDEV_SUPPORT
device evdev
Note: Native and evdev modes are mutually exclusive.
Reviewed by: gonzo, wblock (docs)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D11156
Usbhid's hid_report_size() calculates integral size of all reports of given
kind found in the HID descriptor rather then exact size of report with given
ID as its userland counterpart does. As all input data processed by the
driver is located within the same report, calculate required driver's buffer
size with userland version, imported in one of the previous commits.
This allows us to skip zeroing of buffer on processing of each report.
While here do some minor refactoring.
MFC after: 2 weeks