of the two when calculating the MP throughput average for the ``set
autoload'' implementation.
This makes more sense as all links I know of are full-duplex. This
also means that people may need to adjust their autoload settings
as 100% bandwidth is now the theoretical maximum rather than 200%
(but of course, halfing the current settings is probably not the
correct answer either!).
This involves a ppp version bump as we need to pass an extra
throughput array through the MP local domain socket.
effect the idle timer in different ways.
Submitted by: Stefan Esser <se@freebsd.org>
With adjustments by me to document the option in the man page and to
give the same semantics for outgoing traffic as incoming.
I made the style more consistent in ip.c - this should really have
been done as a separate commit.
o If the new ``filter-decapsulation'' is enabled, delve into UDP packets
that contain 0xff 0x03 as the first two bytes, and if we recognise it
as PROTO_IP, decapsulate it for the purpose of filter checking.
If we recognise it as PROTO_<anything else> mention this for logging
purposes only.
This change is aimed at people running PPPoUDP where the UDP traffic is
being sent over another PPP link. It's desireable to have the top level
link connected all the time, but to have the bottom level link capable
of decapsulating the traffic and comparing the payload against the filters,
thus allowing ``set filter dial ...'' to work in tunnelled environments.
The caveat here is that the top ppp cannot employ any compression layers
without making the data unreadable for the bottom ppp. ``disable deflate
pred1 vj'' and ``deny deflate pred1 vj'' is suggested.
This is invaluable for dial-on-demand connections...
In ppp.linkup:
set log -dns -tcp/ip
and in ppp.linkdown
set log +dns +tcp/ip
giving a much better account of why the link came up.
twice (once for the arg parsing and once to make it a normal character).
Make the man page example consistent.
Reminded by: Bryan Liesner <bleez@netaxs.com>
Warn about -alias being depricated (but still allow it).
Don't moan twice about failing to open any tun device.
Fix a diagnostic and add the -quiet switch to the usage message.
ip_tos == IPTOS_LOWDELAY now get precidence over urgent
packets with ip_tos != IPTOS_LOWDELAY and non-urgent packets
with ip_tos == IPTOS_LOWDELAY.
Enhance the ``set urgent'' syntax to allow for urgent UDP
packets as well as urgent TCP packets.
(LCP/CCP/IPCP), one for urgent IP traffic and one for
everything else.
o Add the ``set urgent'' command for adjusting the list of
urgent port numbers. The default urgent ports are 21, 22,
23, 513, 514, 543 and 544 (Ports 80 and 81 have been
removed from the default priority list).
o Increase the buffered packet threshold from 20 to 30.
o Report the number of packets in the IP output queue and the
list of urgent ports under ``show ipcp''.
that ppp stays in the foreground.
o Add the -quiet switch to quieten ppps startup
o Add the -nat flag and discourage the use of the -alias flag. Both do
the same thing.
o Correct some nat usage strings.
o Change the internal ``alias'' command to ``nat''.
0.81.1 of the i4b code - namely support of the I4B_VR_REQ
ioctl via the i4brbchX device.
Ppp controls the phone number, but idle timers and
SYNC/RAW decisions are still made by isdnd (in isdnd.rc).
This involves a new datalink state machine phase. The
``wait for carrier'' phase happens after dialing but
before logging in. The whole dial state should really
be abstracted so that each device type can deal with it
in its own way (thinking about PPPoE) - but that'll have
to wait.
The ``set cd'' symantics remain the same for tty devices,
but we now delay until we either get CD or timeout waiting
(at which time we drop the link if we require CD).
For i4b devices we always insist on carrier.
Thanks to hm@ for his help, and especially for pointing out
that I *don't* need to re-implement isdnd (that was a huge
waste of time !) :-]
o If we're using RADIUS and the RADIUS mtu is less than our
peers mru/mrru, reduce our mtu to this value for NetBSD too.
o Make struct throughput's sample period dynamic and tweak the ppp
version number to reflect the extra stuff being passed through
the local domain socket as a result (MP mode).
o Measure the current throughput based on the number of samples actually
taken rather than on the full sample period.
o Keep the throughput statisics persistent while being passed to
another ppp invocation through the local domain socket.
o When showing throughput statistics after the timer has stopped, use
the stopped time for overall calculations, not the current time.
Also show the stopped time and how long the current throughput has
been sampled for.
o Use time() consistently in throughput.c
o Tighten up the ``show bundle'' output.
o Introduce the ``set bandwidth'' command.
o Rewrite the ``set autoload'' command. It now takes three arguments
and works based on a rolling bundle throughput average compared against
the theoretical bundle bandwidth over a given period (read: it's now
functional).
negate the sense of rules.
o Remove the redundant (and undocumented) ``host'' and ``port''
words (README.changes updated).
o Don't permit (and ignore) garbage instead of the protocol.
Mostly submitted by: Peter Jeremy <jeremyp@gsmx07.alcatel.com.au>
callback option, and the server sends us CBCP_NONUM, proceed directly
to the network phase rather than insisting on our configured CBCP
option.
Mostly submitted by: kkphang <phang@dgate.po.my>
being the same as the previous (still supported) ``host:port''
syntax for tcp socket devices.
A udp device uses synchronous ppp rather than async, and avoids
the double-retransmit overhead that comes with ppp over tcp (it's
usually a bad idea to transport IP over a reliable transport that
itself is using an unreliable transport). PPP over UDP provides
througput of ** 1.5Mb per second ** with all compression disabled,
maxing out a PPro/200 when running ppp twice, back-to-back.
This proves that PPPoE is plausable in userland....
This change adds a few more handler functions to struct device and
allows derivations of struct device (which may contain their own
data etc) to pass themselves through the unix domain socket for MP.
** At last **, struct physical has lost all the tty crud !
iov2physical() is now smart enough to restore the correct stack of
layers so that MP servers will work again.
The version number has bumped as our MP link transfer contents have
changed (they now may contain a `struct device').
Don't extract the protocol twice in MP mode (resulting in protocol
rejects for every MP packet). This was broken with my original
layering changes.
Add ``Physical'' and ``Sync'' log levels for logging the relevent
raw packets and add protocol-tracking LogDEBUG stuff in various
LayerPush & LayerPull functions.
Assign our physical device name for incoming tcp connections by
calling getpeername().
Assign our physical device name for incoming udp connections from
the address retrieved by the first recvfrom().
the layering.
We now ``stack'' layers as soon as we open the device (when we figure
out what we're dealing with). A static set of `dispatch' routines are
also declared for dealing with incoming packets after they've been
`pulled' up through the stacked layers.
Physical devices are now assigned handlers based on the device type
when they're opened. For the moment there are three device types;
ttys, execs and tcps.
o Increment version number to 2.2
o Make an entry in [uw]tmp for non-tty -direct invocations (after
pap/chap authentication).
o Make throughput counters quad_t's
o Account for the absolute number of mbuf malloc()s and free()s in
``show mem''.
o ``show modem'' becomes ``show physical''.
This was pretty harmless as netmasks on a POINTOPOINT
interface are pretty much ignored, but it looked funny.
Mention the configured netmask in ``show ipcp''.
Describe in more detail what a proxy arp entry is.
that are made in each of the FSMs (LCP, CCP & IPCP) and the
number of REQs/Challenges for PAP/CHAP by accepting more arguments
in the ``set {c,ip,l}cpretry'' and ``set {ch,p}apretry'' commands.
Change the non-convergence thresholds to 3 times the number of configured
REQ tries (rather than the previous fixed ``10''). We now notice
repeated NAKs and REJs rather than just REQs.
Don't suggest that CHAP 0x05 isn't supported when it's not configured.
Fix some bugs that expose themselves with smaller numbers of retries:
o Handle instantaneous disconnects (set device /dev/null) correctly
by stopping all fsm timers in fsm2initial.
o Don't forget to uu_unlock() devices that are files but are not
ttys (set device /dev/zero).
Fix a *HORRENDOUS* bug in RFC1661 (already fixed for an Open event in state
``Closed''):
According to the state transition table, a RCR+ or RCR- received in
the ``Stopped'' state are supposed to InitRestartCounter, SendConfigReq
and SendConfig{Ack,Nak}. However, in ``Stopped'', we haven't yet
done a TLS (or the last thing we did is a TLF). We must therefore
do the TLS at this point !
This was never noticed before because LCP and CCP used not use
LayerStart() for anything interesting, and IPCP tends to go into
Stopped then get a Down because of an LCP RTR rather than getting a
RCR again.
correctly by invoking the timer to get the value before
displaying the message.
Don't assume that a value of 0 is ``random'' in
``show datalink''.
Make the random value between 1 and DIAL_TIMEOUT rather
than between 0 and DIAL_TIMEOUT-1
is complete before checking carrier. If it's there,
the device supports carrier. If it's not it doesn't.
Add the ``set cd'' command for deciding how soon to check
for carrier, and for deciding if carrier is REQUIRED.
The default has changed: Pre 2.0 versions of ppp waited
for 1 second. Version 2 didn't wait, but this causes
problems with some (few?) modems that don't assert carrier
immediately on reporting CONNECT. The one second delay
is back now and can be removed with ``set cd 0''.
Bump the ppp version number in case this needs to be changed
again....
each time rather than making up a new one.
Increase the authname/authkey max sizes to 100 characters.
Allow ``authkey'' specifications beginning with ``!''.
When a challenge is received, the text following the
``!'' is executed as a program (expanding stuff in the same
way that ``sh'' and ``!bg'' do). The program is passed the
peer name, peer challenge and local ``authname'' on standard
input and is expected to output the name/key combination that
should be used to build the CHAP response.
This provides support for Secure ID cards (guess what I was
given at work recently!) using CHAP.
Examples will follow.
