seem to require a special firmware to use TSO. But the firmware is
not available to FreeBSD and Linux claims that the TSO performed by
the firmware is slower than hardware based TSO. Moreover the
firmware based TSO has one known bug which can't handle TSO if
ethernet header + IP/TCP header is greater than 80 bytes. The
workaround for the TSO bug exist but it seems it's too expensive
than not using TSO at all. Some hardwares also have the TSO bug so
limit the TSO to the controllers that are not affected TSO issues
(e.g. 5755 or higher).
While I'm here set VLAN tag bit to all descriptors that belengs to
a frame instead of the first descriptor of a frame. The datasheet
is not clear how to handle VLAN tag bit but it worked either way in
my testing. This makes it simplify TSO configuration a little bit.
Big thanks to davidch@ who sent me detailed TSO information.
Without this I was not able to implement it.
Tested by: current
have a DMA bug when buffer address crosses a multiple of the 4GB
boundary(e.g. 4GB, 8GB, 12GB etc). Limit DMA address to be within
4GB address for these controllers. The second DMA bug limits DMA
address to be within 40bit address space. This bug applies to
BCM5714 and BCM5715 and 5708(bce(4) controller). This is not
actually a MAC controller bug but an issue with the embedded PCIe
to PCI-X bridge in the device. So for BCM5714/BCM5715 controllers
also limit the DMA address to be within 40bit address space.
Special thanks to davidch@ who gave me detailed errata information.
I think this change will fix long standing bge(4) instability
issues on systems with more than 4GB memory.
Reviewed by: davidch
PCI flush to get correct status block update. Add an optimized
interrupt handler that is activated for MSI case. Actual interrupt
handling is done by taskqueue such that the handler does not
require driver lock for Rx path. The MSI capable bge(4) controllers
automatically disables further interrupt once it enters interrupt
state so we don't need PIO access to disable interrupt in interrupt
handler.
update and then clear status block. Previously it used to access
these index without synchronization which may cause problems when
bounce buffers are used. Also add missing bus_dmamap_sync(9) in
polling handler. Since we now update status block in driver, adjust
bus_dmamap_sync(9) for status block.
checking IFF_DRV_RUNNING and IFF_DRV_OACTIVE flags. Also if we
have less than 16 free send BDs set IFF_DRV_OACTIVE and try it
later. Previously bge(4) used to reserve 16 free send BDs after
loading dma maps but hardware just need one reserved send BD. If
prouder index has the same value of consumer index it means the Tx
queue is empty.
While I'm here check IFQ_DRV_IS_EMPTY first to save one lock
operation.
directly access them at fixed address. While I'm here don't touch
other bits of PCIe device control register except max payload size.
Reviewed by: marius
* exception handlers are now run with interrupts disabled, which avoids
many race conditions
* fix some cases where SIGINT only aborts one command and continues the
script, in particular if a SIGINT causes an EINTR error which trumped the
interrupt.
Example:
sh -c 'echo < /some/fifo; echo This should not be printed'
The fifo should not have writers. When pressing ctrl+c to abort the open,
the shell used to continue with the next command.
Example:
sh -c '/bin/echo < /some/fifo; echo This should not be printed'
Similar. Note, however, that this particular case did not and does not work
in interactive mode with job control enabled.
addresses, again. However, change a hostname into an IP address, only
when a host has just one A/AAAA RR.
Requested by: candy__at__kgc.co.jp
MFC after: 2 weeks
This avoids weirdness when 'fc -e vi' or the like is done and there is a
syntax error in the file. Formerly an interactive shell tried to execute
stuff after the syntax error and exited.
This should also avoid similar issues with 'command eval' and 'command .'
when 'command' is implemented properly as in NetBSD sh.
Special builtins did not have this problem since errors in them cause the
shell to exit or to reset various state such as the current command input
file.
Binary divider value 10 specified in datasheet is not a hex 0x10.
UDMA2 should be 33/2 instead of 66/4, which is documented as reverved,
UDMA4 should be 66/2 instead of 66/4, which is definitely wrong.
* increase buffer size from 100 to 256 bytes
* remove implied flush from out2str(), in particular this avoids unnecessary
flushing in the middle of a -x tracing line
* rename dprintf() to out2fmt_flush(), make it flush out2 and use this
function in various places where flushing is desired after an error
message
unlock Giant twice.
While there, bring conditions in the do/while loops closer to style,
that also makes the lines fit into 80 columns.
Reported and tested by: dougb
r197525, so that the creation verifier is handled correctly
in va_atime for 64bit architectures. There were two problems.
One was that the code incorrectly assumed that
sizeof (struct timespec) == 8 and the other was that the tv_sec
field needs to be assigned from a signed 32bit integer, so that
sign extension occurs on 64bit architectures. This is required
for correct operation when exporting ZFS volumes.
Reviewed by: pjd
MFC after: 2 weeks
a feature that libstdc++ depends on to simulate the behavior of libc's
internal '__isthreaded' variable. One benefit of this is that _libc_once()
is now private to _once_stub.c.
Requested by: kan
controller also has support for IP/TCP checksum offloading for Rx
path. But I failed to find to way to enable Rx MAC to compute the
checksum of received frames.
both big-endian and little-endian format in descriptors for Rx path
but I couldn't find equivalent feature in Tx path. So just stick to
little-endian for now.
with the additional property that it is safe for routines in libc to use
in both single-threaded and multi-threaded processes. Multi-threaded
processes use the pthread_once() implementation from the threading library
while single-threaded processes use a simplified "stub" version internal
to libc. The libc stub-version of pthread_once() now also uses the
simplified "stub" version as well instead of being a nop.
Reviewed by: deischen, Matthew Fleming @ Isilon
Suggested by: alc
MFC after: 1 week
the filter as we do from bpf_filter()[1].
- Revert experimental use of contigmalloc(9)/contigfree(9). It has no
performance benefit over malloc(9)/free(9)[2].
Requested by: rwatson[1]
Pointed out by: rwatson, jhb, alc[2]
fully support booting from large volumes.
Tested by: Emil Smolenski ambsd of raisa.eu.org
Submitted by: Matt Reimer mattjreimer of gmail (most of the C bits)
MFC after: 1 week
- fix a transfer cancelling bug/segfault [1]
- correct a return code in the transfer cancel function.
- add new API function, libusb20_tr_bulk_intr_sync().
Submitted by: HPS
Reported by: Robert Jenssen [1]
