- Read interrupt properties at bus enumeration time and store
it into global mapping table.
- At bus_activate_resource() time, given mapping entry is resolved and
connected to real interrupt source. A copy of mapping entry is attached
to given resource.
- At bus_setup_intr() time, mapping entry stored in resource is used
for delivery of requested interrupt configuration.
- For MSI/MSIX interrupts, mapping entry is created within
pci_alloc_msi()/pci_alloc_msix() call.
- For legacy PCI interrupts, mapping entry must be created within
pcib_route_interrupt() by pcib driver itself.
Reviewed by: nwhitehorn, andrew
Differential Revision: https://reviews.freebsd.org/D7493
In some cases, the driver must handle given properties located in
specific OF subnode. Instead of creating duplicate set of function, add
'node' as argument to existing functions, defaulting it to device OF node.
MFC after: 3 weeks
Pressing the PEK (power enable key) will shutdown the board.
Some events are reported to devd via system "PMU" and subsystem
"Battery", "AC" and "USB" such as connected/disconnected.
Some sensors values (power source voltage/current) are reported via
sysctl (dev.axp209_pmu.X.)
It also expose a gpioc node usable in kernel and userland. Only 3 of
the 4 GPIO are exposed (The GPIO3 is different and mostly unused on
boards). Most popular boards uses GPIO1 as a sense pin for OTG power.
Add a dtsi file that adds gpio-controller capability to the device as
upstream doesn't defined it and include it in our custom DTS.
Reviewed by: jmcneill
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D6135
After r285994, sysctl(8) was fixed to use 273.15 instead of 273.20 as 0C
reference and as result, the temperature read in sysctl(8) now exibits a
+0.1C difference.
This commit fix the kernel references to match the reference value used in
sysctl(8) after r285994.
Sponsored by: Rubicon Communications (Netgate)
Also check the return value of copyin(9) to prevent unnecessary allocation in the failure case.
Submitted by: ngie
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D5155
This is compatible with the ds1307, but comparing the mcp7941x datasheet vs the
ds1307 code, appears there is one bit placement difference, so that is now
accounted for.
Relnotes: yes
Most calls to bus_alloc_resource() use "anywhere" as the range, with a given
count. Migrate these to use the new bus_alloc_resource_anywhere() API.
Reviewed by: jhb
Differential Revision: https://reviews.freebsd.org/D5370
support for the i2c, mmc, and gmac clocks. Further clocks can be added as
needed.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed by: jmcneill
Differential Revision: https://reviews.freebsd.org/D5339
Marvell twsi part, however uses different register locations, as such split
the existing driver into Marvell and Allwinner attachments.
While here clean a few style issues.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D4846
The FDT bindings for eeprom parts don't include any metadata about the
device other than the part name encoded in the compatible property.
Instead, a driver is required to have a compiled-in table of information
about the various parts (page size, device capacity, addressing scheme). So
much for FDT being an abstract description of hardware characteristics, huh?
In addition to the FDT-specific changes, this also switches to using the
newer iicbus_transfer_excl() mechanism which holds bus ownership for the
duration of the transfer. Previously this code held the bus across all
the transfers needed to complete the user's IO request, which could be
up to 128KB of data which might occupy the bus for 10-20 seconds. Now the
bus will be released and re-aquired between every page-sized (8-256 byte)
transfer, making this driver a much nicer citizen on the i2c bus.
The hint-based configuration mechanism is still in place for non-FDT systems.
Michal Meloun contributed some of the code for these changes.
while holding exclusive ownership of the bus. This is the routine most
slave drivers should use unless they have a need to acquire and hold the
bus across a series of related operations that involves multiple transfers.
If the bus is detached and deleted by a call to device_delete_child() or
device_delete_children() on a device higher in the tree, I²C children
were already detached and deleted. So the device_t pointer stored in sc
points to freed memory: we must not try to delete it again.
By using device_delete_children(), we let subr_bus.c figure out if there
are children to take care of.
While here, make sure iicbus_detach() and iicoc_detach() call
device_delete_children() too, to be safe.
Reviewed by: jhb, imp
Approved by: jhb, imp
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D3926
these functions are thin wrappers around calling the hardware-layer driver,
but some of them do sanity checks and return an error. Since the hardware
layer can only return IIC_Exxxxx status values, the iicbus helper functions
must also adhere to that, so that drivers at higher layers can assume that
any non-zero status value is an IIC_Exxxx value that provides details about
what happened at the hardware layer (sometimes those details are important
for certain slave drivers).
errno values that are at least vaguely equivelent. Also add a new status
value, IIC_ERESOURCE, to indicate a failure to acquire memory or other
required resources to complete a transaction.
The IIC_Exxxxxx values are supposed to communicate low-level details of the
i2c transaction status between the lowest-layer hardware driver and
higher-layer bus protocol and device drivers for slave devices on the bus.
Most of those slave drivers just return all status values from the lower
layers directly to their callers, resulting in crazy error reporting from a
user's point of view (things like timeouts being reported as "no such
process"). Now there's a helper function to make it easier to start
cleaning up all those drivers.
Make it clearer what each one means in the comments that define them.
IIC_BUSBSY was used in many places to mean two different things, either
"someone else has reserved the bus so you have to wait until they're done"
or "the signal level on the bus was not in the state I expected before/after
issuing some command".
Now IIC_BUSERR is used consistantly to refer to protocol/signaling errors,
and IIC_BUSBSY refers to ownership/reservation of the bus.
perform a stop operation on the bus if there was an error, otherwise the
bus will remain hung forever. Consistantly use 'if (error != 0)' style in
the function.
bus_alloc_resource(), bus_release_resource() and bus_set_resource()
(bus_generic_rl_alloc_resource(), bus_generic_rl_release_resource() and
bus_generic_rl_set_resource() respectively).
Do not print the resources for nomatch devices.
Use the inherited method for bus_get_resource_list() on ofw_iicbus.c.
Submitted by: jhb and Michal Meloun (D2033)
controllers.
Call iicbus_transfer() from the device context and not from the iicbus
context.
I am committing a slightly different patch, so if something break, it is
probably my fault.
PR: 199496
Submitted by: Juraj Lutter <otis@sk.FreeBSD.org>
--Allow multiple open iic fds by storing addressing state in cdevpriv
--Fix, as much as possible, the baked-in race conditions in the iic
ioctl interface by requesting bus ownership on I2CSTART, releasing it on
I2CSTOP/I2CRSTCARD, and requiring bus ownership by the current cdevpriv
to use the I/O ioctls
--Reduce internal iic buffer size and remove 1K read/write limit by
iteratively calling iicbus_read/iicbus_write
--Eliminate dynamic allocation in I2CWRITE/I2CREAD
--Move handling of I2CRDWR to separate function and improve error handling
--Add new I2CSADDR ioctl to store address in current cdevpriv so that
I2CSTART is not needed for read(2)/write(2) to work
--Redesign iicbus_request_bus() and iicbus_release_bus():
--iicbus_request_bus() no longer falls through if the bus is already
owned by the requesting device. Multiple threads on the same device may
want exclusive access. Also, iicbus_release_bus() was never
device-recursive anyway.
--Previously, if IICBUS_CALLBACK failed in iicbus_release_bus(), but
the following iicbus_poll() call succeeded, IICBUS_CALLBACK would not be
issued again
--Do not hold iicbus mtx during IICBUS_CALLBACK call. There are
several drivers that may sleep in IICBUS_CALLBACK, if IIC_WAIT is passed.
--Do not loop in iicbus_request_bus if IICBUS_CALLBACK returns
EWOULDBLOCK; instead pass that to the caller so that it can retry if so
desired.
Differential Revision: https://reviews.freebsd.org/D2140
Reviewed by: imp, jhb, loos
Approved by: kib (mentor)
Many thanks to ian who gently provided me the DS1307 breakout board.
Tested on: Raspberry pi
Differential Revision: https://reviews.freebsd.org/D2022
Reviewed by: rpaulo
I2C real-time clock (RTC).
The DS3231 has an integrated temperature-compensated crystal oscillator
(TXCO) and crystal.
DS3231 has a temperature sensor, an independent 32kHz output (which can be
turned on and off by the driver) and another output that can be used as
interrupt for alarms or as a second square-wave output, which frequency and
operation mode can be set by driver sysctl(8) knobs.
Differential Revision: https://reviews.freebsd.org/D1016
Reviewed by: ian, rpaulo
Tested on: Raspberry pi model B
The current support for controlling i2c bus speed is an inconsistant mess.
There are 4 symbolic speed values defined, UNKNOWN, SLOW, FAST, FASTEST.
It seems to be universally assumed that SLOW means the standard 100KHz
rate from the original spec. Nothing ever calls iicbus_reset() with a
speed of FAST, although some drivers would treat it as the 400KHz standard
speed. Mostly iicbus_reset() is called with the speed set to UNKNOWN or
FASTEST, and there's really no telling what any individual driver will do
with those.
The speed of an i2c bus is limited by the speed of the slowest device on
the bus. This means that generally the bus speed needs to be configured
based on the board/system and the components within it. Historically for
i2c we've configured with device hints. Newer systems use FDT data and it
documents a clock-frequency property for i2c busses. Hobbyists and
developers are likely to want on the fly changes. These changes provide
all 3 methods, but do not require any existing drivers to change to use
the new facilities.
This adds an iicbus method, iicbus_get_frequency(dev, speed) that gets the
frequency for the requested symbolic speed. If the symbolic speed is SLOW
or if there is no speed configured for the bus, the returned value is
100KHz, always. Otherwise, if bus speed is configured by hints, fdt,
tunable, or sysctl, that speed is returned. It also adds a helper
function, iicbus_init_frequency() that any bus driver subclassed from
iicbus can initialize the frequency from some other source of info.
Initial driver implementations are provided for Freescale and TI.
Differential Revision: https://reviews.freebsd.org/D1174
PR: 195009
transfers to be default. It simplifies porting code which assumes
such settings.
Discussed with: avg, llos, nwhitehorn
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
For compatibility, 'device windtunnel' is still supported, but one should use
'device adm1030' instead, and this has been updated in GENERIC and NOTES.
There's a very remote, but possible, chance that the integer part read will
fail, but the fraction read succeeds, at which point the reported temperature is
invalid.
Reported by: Matthew Rezny
MFC after: 3 weeks
This driver supports the low and high precision models (9 and 11 bits) and
it will auto-detect the both variants.
The driver expose the temperature registers (actual temperature, shutdown
and hysteresys temperature) and also the configuration register.
It was tested on FDT systems: RPi, BBB and on non-FDT systems: AR71xx, with
both, hardware i2c controllers (when available) and gpioiic(4).
This provides a simple and cheap way for verifying the i2c bus on embedded
systems.
This change makes ofw_iicbus attach to iicbb(4) controllers in addition to
the already supported i2c host bridges (iichb).
On iicbb(4) allow the direct access of the OFW parent node by its children,
so they can be directly attached to iicbb(4) node on the DTS without the
need of describing the i2c bus.
Approved by: adrian (mentor, implicit)
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
extremely outdated, and I doubt that it was ever used for ifnet drivers.
It was used for AF_INET sockets in pre-FreeBSD time.
Approved by: re (hrs)
Sponsored by: Nginx, Inc.
doesn't automatically clear when VDD rises above Vlow again and needs to be
cleared manually. However, apparently this needs all of the time registers
to be set, i.e. pcf8563_settime(), and not just PCF8563_R_SECOND in order
for PCF8563_R_SECOND_VL to stick. Thus, we just issue a warning during
pcf8563_attach() rather than failing with ENXIO in case it is set.
MFC after: 3 days
Add a Simple polled driver iicoc for the OpenCores I2C controller. This
is used in Netlogic XLP processors.
Submitted by: Sreekanth M. S. (kanthms at netlogicmicro com)
The earlier version of the driver is sys/mips/rmi/dev/iic/ds1374u.c
Convert all references to ds1374u to ds1374, and use DEVMETHOD_END.
Also update the license header as Netlogic is now Broadcom.
clients.
These are helful when making certain drivers work on both Linux
and FreeBSD without changing the code flow too much.
Reviewed by: kib, wlosh
MFC after: 1 month
* Right now the delay is hard coded at 10uS. This is a bit long when doing lots
of periodic i2c transactions. So create a 'udelay' parameter and initialise it
to 10. This can be tuned later.
* Add a newline after a transaction finishes, so the debugging output isn't so
horrible.
These realtek switch PHYs speak a variant of i2c with some slightly
modified handling.
From the submitter, slightly modified now that some further digging
has been done:
The I2C framework makes a assumption that the read/not-write bit of the first
byte (the address) indicates whether reads or writes are to follow.
The RTL8366 family uses the bus: after sending the address+read/not-write byte,
two register address bytes are sent, then the 16-bit register value is sent
or received. While the register write access can be performed as a 4-byte
write, the read access requires the read bit to be set, but the first two bytes
for the register address then need to be transmitted.
This patch maintains the i2c protocol behaviour but allows it to be relaxed
(for these kinds of switch PHYs, and whatever else Realtek may do with this
almost-but-not-quite i2c bus) - by setting the "strict" hint to 0.
The "strict" hint defaults to 1.
Submitted by: Stefan Bethke <stb@lassitu.de>
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
setting (either default or if supported as set by SIOCSIFFIB, e.g.
from ifconfig).
Submitted by: Alexander V. Chernikov (melifaro ipfw.ru)
Reviewed by: julian
MFC after: 2 weeks
- Add retry loops in the i2c read/write functions.
- Combied the ADC channel selection and readout of the value into
one iicbus_transfer to avoid possible races.
Reviewed by: nwhitehorn
- Add a retry loop for the i2c sensor reading.
- Check on busy status of the chip and on invalid values.
- Fix a typo in a comment.
- Replace the constant 2732 with the ZERO_C_TO_K macro.
Approved by: nwhitehorn (mentor)
- Add a retry loop for the i2c sensor reading.
- Update the sensor handling for sensors which do not have a location
entry. [1]
Submitted by: [1] Justin Hibbits.
Approved by: nwhitehorn (mentor)
for this sensor. Instead of leaving this location empty we use here
the default name 'sensor'.
Submitted by: Justin Hibbits <chmeeedalf at gmail dot com>
Approved by: nwhitehorn (mentor)
functionality is the same, a difference is that the DS1775 has a better
precision than the LM75. But we do not use it in our setup. Make the
LM75 work the same as the DS1775.
Fix a typo in device_set_desc.
Tested by: Paul Mather <paul at gromit dlib vt edu>
Approved by: nwhitehorn (mentor)
PowerMac7,2.
- The fcu driver lets us read and write the fan RPMs for all fans in the
PowerMac7,2. This driver is PowerMac specific.
- The ds1775 is a driver to read the temperature for the drive bay sensor.
- The max6690 is another driver to read temperatures. Here it is used to
read the inlet, the backside and the U3 heatsink temperature.
An additional driver, the ad7417, will follow later.
Thanks to nwhitehorn for guiding me through this driver development.
Approved by: nwhitehorn (mentor)
This reflects actual type used to store and compare child device orders.
Change is mostly done via a Coccinelle (soon to be devel/coccinelle)
semantic patch.
Verified by LINT+modules kernel builds.
Followup to: r212213
MFC after: 10 days
queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
respectivly. This will allow one to have a kernel with both devices
present and use it for multiple boards with different types of RTC
sitting on a bus.
Discussed with: imp
work when the bus attaches its own children. Instead of hardcoding a unit
number and returning BUS_PROBE_NOWILDCARD, which will break multiple iicbus
systems, check in the probe routine whether the device address is 0. Real
I2C devices will never have this address, but devices added with
BUS_ADD_CHILD() will.
Requested by: jhb
Reviewed by: jhb
indicated I2C devices, and provides an ofw_bus interface for driver probing.
This should be MI, but is currently provided only on PowerPC due to lack of
sparc64 hardware with an I2C controller.
Discussed on: freebsd-arch
subclasses as are available with PCI. Changes I2C device drivers without
real probe logic to return BUS_PROBE_NOWILDWARD to avoid interference with
firmware bus enumeration, and reduces the probe priority of the iicbus
base driver to allow subclass attachment at higher priority.
Discussed on: freebsd-arch
Compilation of the AVILA kernel failed because of two reasons:
- It needed curthread, which is defined through <sys/pcpu.h>.
- It still referred the softc's sc_mtx field, which has been replaced by
sc_lock three weeks ago.
To solve the first problem, I decided to include <sys/pcpu.h> in
<sys/sx.h>, which also seems to be done by <sys/mutex.h> and
<sys/rwlock.h>. Those header files also require curthread.
Approved by: jhb
- Extend the DS1339 driver to recognize more chips in the family:
DS1337, DS1338, DS1339 are now supported
- Provide run-time chip detection
Reviewed, tested by: stas
Obtained from: Piotr Ziecik kosmo ! semihalf dot com
- ad7418(4) uses an sx lock instead of a mtx since the iicbus(4) stuff it
calls can sleep (request_bus()). Also, I expanded the locking slightly
to serialize writes to data stored in the softc.
- Similarly, the icee(4) driver now uses an sx lock instead of a mutex.
I also removed the pointless OPENED flag and flags field from the softc.
- The locking for the ic(4) driver was a bit trickier:
- Add a mutex to the softc to protect softc data.
- The driver uses malloc'd buffers that are the size of the interface
MTU to send and receive packets. Previously, these were allocated
every time the interface was brought up and anytime the MTU was
changed, with various races that could result in memory leaks. I
changed this to be a bit simpler and more like other NIC drivers in
that we allocate buffers during attach for the default MTU size and
only reallocate them on MTU changes. The reallocation procedure
goes to some lengths with various flags to not replace either the
the receive or transmit buffers while the driver is busy receiving
or transmitting a packet.
- Store the device_t of the driver in the softc instead of detours into
new-bus using if_dunit from the ifnet and an even more bizarre detour
to get the softc instead of using if_softc.
- Drop the driver mutex when invoking netisr_dispatch() to pass the
packet up to IP.
- Use if_printf().
- Add an sx lock to the iic(4) driver to serialize open(), close(), read(),
and write and to protect sc_addr and sc_count in the softc.
- Use cdev->si_drv1 instead of using the minor number of the cdev to
lookup the softc via newbus in iic(4).
- Store the device_t in the softc to avoid a similar detour via minor
numbers in iic(4).
- Only add at most one instance of iic(4) and iicsmb(4) to each iicbus(4)
instance, and do it in the child driver.
- Add a mutex to the iicbus(4) softc to synchronize the request/release bus
stuff.
- Use __BUS_ACCESSOR() for IICBUS_ACCESSOR() instead of rolling our own.
- Add a mutex to the iicsmb(4) softc to protect softc state updated in the
interrupt handler.
- Remove Giant from all the smbus methods in iicsmb(4) now that all the
iicbus(4) backend is locked.
- Just grab Giant in the ixp425_iic(4) driver since this driver uses
a shared address/data register window pair to access the actual
I2C registers. None of the other ixp425 drivers lock access to these
shared address/data registers yet and that would need to be done before
this could use any meaningful locking.
- Add locking to the interrupt handler and 'iicbus_reset' methods of the
at91_twi(4) driver.
- Add locking to the pcf(4) driver. Other pcf(4) fixes include:
- Don't needlessly zero the softc.
- Use bus_foo rather than bus_space_foo and remove bus space tag and
handle from softc.
- The lpbb(4) driver just grabs Giant for now. This will be refined later
when ppbus(4) is locked.
- As was done with smbus earlier, move the DRIVER_MODULE() lines to match
the bus driver (either iicbus or iicbb) to the bridge driver into the
bridge drivers.
Tested by: sam (arm/ixp425)
some devices (and not others). To get instances onto the iicbus, one
now needs hints or an identify routine. We also do not probe the bus
for devices because many iic devices cannot be safely probed (and when
they can, the probe order turns out to be somewhat difficult to get
right).
# I'm not 100% sure that the iicsmb removal is right. Please contact me if
# this causes difficulty.
Add a note that suggests a cleanup.
Note: This patch was derived based on looking at the pvrxxx/pvr250
ports' Makefiles only, and may be incomplete. It is not derived from
anything I saw from Hauppage.
- Change smbus_callback() to pass a void * rather than caddr_t.
- Change smbus_bread() to pass a pointer to the count and have it be an
in/out parameter. The input is the size of the buffer (same as before),
but on return it will contain the actual amount of data read back from
the bus. Note that this value may be larger than the input value. It
is up to the caller to treat this as an error if desired.
- Change the SMB_BREAD ioctl to write out the updated struct smbcmd which
will contain the actual number of bytes read in the 'count' field. To
preserve the previous ABI, the old ioctl value is mapped to SMB_OLD_BREAD
which doesn't copy the updated smbcmd back out to userland. I doubt anyone
actually used the old BREAD anyway as it was rediculous to do a bulk-read
but not tell the using program how much data was actually read.
- Make the smbus driver and devclass public in the smbus module and
push all the DRIVER_MODULE()'s for attaching the smbus driver to
various foosmb drivers out into the foosmb modules. This makes all
the foosmb logic centralized and allows new foosmb modules to be
self-contained w/o having to hack smbus.c everytime a new smbus driver
is added.
- Add a new SMB_EINVAL error bit and use it in place of EINVAL to return
an error for bad arguments (such as invalid counts for bread and bwrite).
- Map SMB bus error bits to EIO in smbus_error().
- Make the smbus driver call bus_generic_probe() and require child drivers
such as smb(4) to create device_t's via identify routines. Previously,
smbus just created one anonymous device during attach, and if you had
multiple drivers that could attach it was just random chance as to which
driver got to probe for the sole device_t first.
- Add a mutex to the smbus(4) softc and use it in place of dummy splhigh()
to protect the 'owner' field and perform necessary synchronization for
smbus_request_bus() and smbus_release_bus().
- Change the bread() and bwrite() methods of alpm(4), amdpm(4), and
viapm(4) to only perform a single transaction and not try to use a
loop of multiple transactions for a large request. The framing and
commands to use for a large transaction depend on the upper-layer
protocol (such as SSIF for IPMI over SMBus) from what I can tell, and the
smb(4) driver never allowed bulk read/writes of more than 32-bytes
anyway. The other smb drivers only performed single transactions.
- Fix buffer overflows in the bread() methods of ichsmb(4), alpm(4),
amdpm(4), amdsmb(4), intpm(4), and nfsmb(4).
- Use SMB_xxx errors in viapm(4).
- Destroy ichsmb(4)'s mutex after bus_generic_detach() to avoid problems
from child devices making smb upcalls that would use the mutex during
their detach methods.
MFC after: 1 week
Reviewed by: jmg (mostly)
forcing all transfers to do the start read/write stop by hand. Some
smart bridges prefer this sort of operation, and this allows us to
support their features more easily. When bridges don't support it, we
fall back to using the old-style opertaions. Expand the ioctl
interface to expose this function. Unlike the old-style interface,
this interface is thread safe, even on old bridges.
as pcf_ebus and pcf_isa, they should probably be fixed back to pcf),
and bti2c doesn't exist, bktr has smbus or iicbb as children..
Brought to you by: http://people.FreeBSD.org/~jmg/driver.pdf
IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to
ifnet.if_drv_flags. Device drivers are now responsible for
synchronizing access to these flags, as they are in if_drv_flags. This
helps prevent races between the network stack and device driver in
maintaining the interface flags field.
Many __FreeBSD__ and __FreeBSD_version checks maintained and continued;
some less so.
Reviewed by: pjd, bz
MFC after: 7 days
a DLT_NULL interface. In particular:
1) Consistently use type u_int32_t for the header of a
DLT_NULL device - it continues to represent the address
family as always.
2) In the DLT_NULL case get bpf_movein to store the u_int32_t
in a sockaddr rather than in the mbuf, to be consistent
with all the DLT types.
3) Consequently fix a bug in bpf_movein/bpfwrite which
only permitted packets up to 4 bytes less than the MTU
to be written.
4) Fix all DLT_NULL devices to have the code required to
allow writing to their bpf devices.
5) Move the code to allow writing to if_lo from if_simloop
to looutput, because it only applies to DLT_NULL devices
but was being applied to other devices that use if_simloop
possibly incorrectly.
PR: 82157
Submitted by: Matthew Luckie <mjl@luckie.org.nz>
Approved by: re (scottl)
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
NULL name in device_add_child(), explicitly name all of our known
child drivers in order to give them a chance to attach to us.
Otherwise, only the first one present would be probed and attached.
Reviewed by: nsouch
MFC after: 1 month
Introduce d_version field in struct cdevsw, this must always be
initialized to D_VERSION.
Flip sense of D_NOGIANT flag to D_NEEDGIANT, this involves removing
four D_NOGIANT flags and adding 145 D_NEEDGIANT flags.
Free approx 86 major numbers with a mostly automatically generated patch.
A number of strategic drivers have been left behind by caution, and a few
because they still (ab)use their major number.
a new bpf_mtap2 routine that does the right thing for an mbuf
and a variable-length chunk of data that should be prepended.
o while we're sweeping the drivers, use u_int32_t uniformly when
when prepending the address family (several places were assuming
sizeof(int) was 4)
o return M_ASSERTVALID to BPF_MTAP* now that all stack-allocated
mbufs have been eliminated; this may better be moved to the bpf
routines
Reviewed by: arch@ and several others
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
drivers that implemnt the i2c bit banging bus interface not have to
recompile iicbb in order to add an attachment for it.
This will mean the bktr and other definitions can go back to their
respective drivers.
drain routines are done by swi_net, which allows for better queue control
at some future point. Packets may also be directly dispatched to a netisr
instead of queued, this may be of interest at some installations, but
currently defaults to off.
Reviewed by: hsu, silby, jayanth, sam
Sponsored by: DARPA, NAI Labs
branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
o don't strip the Ethernet header from inbound packets; pass packets
up the stack intact (required significant changes to some drivers)
o reference common definitions in net/ethernet.h (e.g. ETHER_ALIGN)
o track ether_ifattach/ether_ifdetach API changes
o track bpf changes (use BPF_TAP and BPF_MTAP)
o track vlan changes (ifnet capabilities, revised processing scheme, etc.)
o use if_input to pass packets "up"
o call ether_ioctl for default handling of ioctls
Reviewed by: many
Approved by: re
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
before adding/removing packets from the queue. Also, the if_obytes and
if_omcasts fields should only be manipulated under protection of the mutex.
IF_ENQUEUE, IF_PREPEND, and IF_DEQUEUE perform all necessary locking on
the queue. An IF_LOCK macro is provided, as well as the old (mutex-less)
versions of the macros in the form _IF_ENQUEUE, _IF_QFULL, for code which
needs them, but their use is discouraged.
Two new macros are introduced: IF_DRAIN() to drain a queue, and IF_HANDOFF,
which takes care of locking/enqueue, and also statistics updating/start
if necessary.
non-device code.
* Re-implement the method dispatch to improve efficiency. The new system
takes about 40ns for a method dispatch on a 300Mhz PII which is only
10ns slower than a direct function call on the same hardware.
This changes the new-bus ABI slightly so make sure you re-compile any
driver modules which you use.
is an application space macro and the applications are supposed to be free
to use it as they please (but cannot). This is consistant with the other
BSD's who made this change quite some time ago. More commits to come.
device_add_child_ordered(). 'ivars' may now be set using the
device_set_ivars() function.
This makes it easier for us to change how arbitrary data structures are
associated with a device_t. Eventually we won't be modifying device_t
to add additional pointers for ivars, softc data etc.
Despite my best efforts I've probably forgotten something so let me know
if this breaks anything. I've been running with this change for months
and its been quite involved actually isolating all the changes from
the rest of the local changes in my tree.
Reviewed by: peter, dfr
have been there in the first place. A GENERIC kernel shrinks almost 1k.
Add a slightly different safetybelt under nostop for tty drivers.
Add some missing FreeBSD tags
This means that we will not have to have a bpf and a non-bpf version
of our driver modules.
This does not open any security hole, because the bpf core isn't loadable
The drivers left unchanged are the "cross platform" drivers where the respective
maintainers are urged to DTRT, whatever that may be.
Add a couple of missing FreeBSD tags.
- device_print_child() either lets the BUS_PRINT_CHILD
method produce the entire device announcement message or
it prints "foo0: not found\n"
Alter sys/kern/subr_bus.c:bus_generic_print_child() to take on
the previous behavior of device_print_child() (printing the
"foo0: <FooDevice 1.1>" bit of the announce message.)
Provide bus_print_child_header() and bus_print_child_footer()
to actually print the output for bus_generic_print_child().
These functions should be used whenever possible (unless you can
just use bus_generic_print_child())
The BUS_PRINT_CHILD method now returns int instead of void.
Modify everything else that defines or uses a BUS_PRINT_CHILD
method to comply with the above changes.
- Devices are 'on' a bus, not 'at' it.
- If a custom BUS_PRINT_CHILD method does the same thing
as bus_generic_print_child(), use bus_generic_print_child()
- Use device_get_nameunit() instead of both
device_get_name() and device_get_unit()
- All BUS_PRINT_CHILD methods return the number of
characters output.
Reviewed by: dfr, peter
The cdevsw_add() function now finds the major number(s) in the
struct cdevsw passed to it. cdevsw_add_generic() is no longer
needed, cdevsw_add() does the same thing.
cdevsw_add() will print an message if the d_maj field looks bogus.
Remove nblkdev and nchrdev variables. Most places they were used
bogusly. Instead check a dev_t for validity by seeing if devsw()
or bdevsw() returns NULL.
Move bdevsw() and devsw() functions to kern/kern_conf.c
Bump __FreeBSD_version to 400006
This commit removes:
72 bogus makedev() calls
26 bogus SYSINIT functions
if_xe.c bogusly accessed cdevsw[], author/maintainer please fix.
I4b and vinum not changed. Patches emailed to authors. LINT
probably broken until they catch up.
Reformat and initialize correctly all "struct cdevsw".
Initialize the d_maj and d_bmaj fields.
The d_reset field was not removed, although it is never used.
I used a program to do most of this, so all the files now use the
same consistent format. Please keep it that way.
Vinum and i4b not modified, patches emailed to respective authors.
