array with a singleton.
Also, pccbb isa attachment is never going to happen, do disconnect it from the
build (will delete this in future commit). It would need to be updated as well,
but since this code is effectively dead code, remove it from the build instead.
These were obtained from the Chelsio Unified Wire v3.12.0.1 beta
release.
Note that the firmwares are not uuencoded any more.
MFH: 1 month
Sponsored by: Chelsio Communications
Uses two GPIO pins as MDC (clock) and MDIO (bidirectional I/O), relies
on mii_bitbang.
Tested on SG-3200 where the PHY for one of the ports is wired independently
of the SoC MDIO bus.
Sponsored by: Rubicon Communications, LLC (Netgate)
ConnectX-6 DX.
Currently TLS v1.2 and v1.3 with AES 128/256 crypto over TCP/IP (v4
and v6) is supported.
A per PCI device UMA zone is used to manage the memory of the send
tags. To optimize performance some crypto contexts may be cached by
the UMA zone, until the UMA zone finishes the memory of the given send
tag.
An asynchronous task is used manage setup of the send tags towards the
firmware. Most importantly setting the AES 128/256 bit pre-shared keys
for the crypto context.
Updating the state of the AES crypto engine and encrypting data, is
all done in the fast path. Each send tag tracks the TCP sequence
number in order to detect non-contiguous blocks of data, which may
require a dump of prior unencrypted data, to restore the crypto state
prior to wire transmission.
Statistics counters have been added to count the amount of TLS data
transmitted in total, and the amount of TLS data which has been dumped
prior to transmission. When non-contiguous TCP sequence numbers are
detected, the software needs to dump the beginning of the current TLS
record up until the point of retransmission. All TLS counters utilize
the counter(9) API.
In order to enable hardware TLS offload the following sysctls must be set:
kern.ipc.mb_use_ext_pgs=1
kern.ipc.tls.ifnet.permitted=1
kern.ipc.tls.enable=1
Sponsored by: Mellanox Technologies
The hardware offload is primarily targeted for TLS v1.2 and v1.3,
using AES 128/256 bit pre-shared keys. This patch adds all the needed
hardware structures, capabilites and firmware commands.
Sponsored by: Mellanox Technologies
This makes it possible to retrieve per-connection statistical
information such as the receive window size, RTT, or goodput,
using a newly added TCP_STATS getsockopt(3) option, and extract
them using the stats_voistat_fetch(3) API.
See the net/tcprtt port for an example consumer of this API.
Compared to the existing TCP_INFO system, the main differences
are that this mechanism is easy to extend without breaking ABI,
and provides statistical information instead of raw "snapshots"
of values at a given point in time. stats(3) is more generic
and can be used in both userland and the kernel.
Reviewed by: thj
Tested by: thj
Obtained from: Netflix
Relnotes: yes
Sponsored by: Klara Inc, Netflix
Differential Revision: https://reviews.freebsd.org/D20655
This adds support for ifnet (NIC) KTLS using Chelsio T6 adapters.
Unlike the TOE-based KTLS in r353328, NIC TLS works with non-TOE
connections.
NIC KTLS on T6 is not able to use the normal TSO (LSO) path to segment
the encrypted TLS frames output by the crypto engine. Instead, the
TOE is placed into a special setup to permit "dummy" connections to be
associated with regular sockets using KTLS. This permits using the
TOE to segment the encrypted TLS records. However, this approach does
have some limitations:
1) Regular TOE sockets cannot be used when the TOE is in this special
mode. One can use either TOE and TOE-based KTLS or NIC KTLS, but
not both at the same time.
2) In NIC KTLS mode, the TOE is only able to accept a per-connection
timestamp offset that varies in the upper 4 bits. Put another way,
only connections whose timestamp offset has the 28 lower bits
cleared can use NIC KTLS and generate correct timestamps. The
driver will refuse to enable NIC KTLS on connections with a
timestamp offset with any of the lower 28 bits set. To use NIC
KTLS, users can either disable TCP timestamps by setting the
net.inet.tcp.rfc1323 sysctl to 0, or apply a local patch to the
tcp_new_ts_offset() function to clear the lower 28 bits of the
generated offset.
3) Because the TCP segmentation relies on fields mirrored in a TCB in
the TOE, not all fields in a TCP packet can be sent in the TCP
segments generated from a TLS record. Specifically, for packets
containing TCP options other than timestamps, the driver will
inject an "empty" TCP packet holding the requested options (e.g. a
SACK scoreboard) along with the segments from the TLS record.
These empty TCP packets are counted by the
dev.cc.N.txq.M.kern_tls_options sysctls.
Unlike TOE TLS which is able to buffer encrypted TLS records in
on-card memory to handle retransmits, NIC KTLS must re-encrypt TLS
records for retransmit requests as well as non-retransmit requests
that do not include the start of a TLS record but do include the
trailer. The T6 NIC KTLS code tries to optimize some of the cases for
requests to transmit partial TLS records. In particular it attempts
to minimize sending "waste" bytes that have to be given as input to
the crypto engine but are not needed on the wire to satisfy mbufs sent
from the TCP stack down to the driver.
TCP packets for TLS requests are broken down into the following
classes (with associated counters):
- Mbufs that send an entire TLS record in full do not have any waste
bytes (dev.cc.N.txq.M.kern_tls_full).
- Mbufs that send a short TLS record that ends before the end of the
trailer (dev.cc.N.txq.M.kern_tls_short). For sockets using AES-CBC,
the encryption must always start at the beginning, so if the mbuf
starts at an offset into the TLS record, the offset bytes will be
"waste" bytes. For sockets using AES-GCM, the encryption can start
at the 16 byte block before the starting offset capping the waste at
15 bytes.
- Mbufs that send a partial TLS record that has a non-zero starting
offset but ends at the end of the trailer
(dev.cc.N.txq.M.kern_tls_partial). In order to compute the
authentication hash stored in the trailer, the entire TLS record
must be sent as input to the crypto engine, so the bytes before the
offset are always "waste" bytes.
In addition, other per-txq sysctls are provided:
- dev.cc.N.txq.M.kern_tls_cbc: Count of sockets sent via this txq
using AES-CBC.
- dev.cc.N.txq.M.kern_tls_gcm: Count of sockets sent via this txq
using AES-GCM.
- dev.cc.N.txq.M.kern_tls_fin: Count of empty FIN-only packets sent to
compensate for the TOE engine not being able to set FIN on the last
segment of a TLS record if the TLS record mbuf had FIN set.
- dev.cc.N.txq.M.kern_tls_records: Count of TLS records sent via this
txq including full, short, and partial records.
- dev.cc.N.txq.M.kern_tls_octets: Count of non-waste bytes (TLS header
and payload) sent for TLS record requests.
- dev.cc.N.txq.M.kern_tls_waste: Count of waste bytes sent for TLS
record requests.
To enable NIC KTLS with T6, set the following tunables prior to
loading the cxgbe(4) driver:
hw.cxgbe.config_file=kern_tls
hw.cxgbe.kern_tls=1
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D21962
Update the NetBSD Kernel Concurrency Sanitizer (KCSAN) runtime to work in
the FreeBSD kernel. It is a useful tool for finding data races between
threads executing on different CPUs.
This can be enabled by enabling KCSAN in the kernel config, or by using the
GENERIC-KCSAN amd64 kernel. It works on amd64 and arm64, however the later
needs a compiler change to allow -fsanitize=thread that KCSAN uses.
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D22315
This kind of clock nodes represent temporary placeholder for clocks
defined later in boot process. Also, these are necessary to break
circular dependencies occasionally occurring in complex clock graphs.
MFC after: 3 weeks
NetGDB(4) is a component of a system using a panic-time network stack to
remotely debug crashed FreeBSD kernels over the network, instead of
traditional serial interfaces.
There are three pieces in the complete NetGDB system.
First, a dedicated proxy server must be running to accept connections from
both NetGDB and gdb(1), and pass bidirectional traffic between the two
protocols.
Second, the NetGDB client is activated much like ordinary 'gdb' and
similarly to 'netdump' in ddb(4) after a panic. Like other debugnet(4)
clients (netdump(4)), the network interface on the route to the proxy server
must be online and support debugnet(4).
Finally, the remote (k)gdb(1) uses 'target remote <proxy>:<port>' (like any
other TCP remote) to connect to the proxy server.
The NetGDB v1 protocol speaks the literal GDB remote serial protocol, and
uses a 1:1 relationship between GDB packets and sequences of debugnet
packets (fragmented by MTU). There is no encryption utilized to keep
debugging sessions private, so this is only appropriate for local
segments or trusted networks.
Submitted by: John Reimer <john.reimer AT emc.com> (earlier version)
Discussed some with: emaste, markj
Relnotes: sure
Differential Revision: https://reviews.freebsd.org/D21568
Debugnet is a simplistic and specialized panic- or debug-time reliable
datagram transport. It can drive a single connection at a time and is
currently unidirectional (debug/panic machine transmit to remote server
only).
It is mostly a verbatim code lift from netdump(4). Netdump(4) remains
the only consumer (until the rest of this patch series lands).
The INET-specific logic has been extracted somewhat more thoroughly than
previously in netdump(4), into debugnet_inet.c. UDP-layer logic and up, as
much as possible as is protocol-independent, remains in debugnet.c. The
separation is not perfect and future improvement is welcome. Supporting
INET6 is a long-term goal.
Much of the diff is "gratuitous" renaming from 'netdump_' or 'nd_' to
'debugnet_' or 'dn_' -- sorry. I thought keeping the netdump name on the
generic module would be more confusing than the refactoring.
The only functional change here is the mbuf allocation / tracking. Instead
of initiating solely on netdump-configured interface(s) at dumpon(8)
configuration time, we watch for any debugnet-enabled NIC for link
activation and query it for mbuf parameters at that time. If they exceed
the existing high-water mark allocation, we re-allocate and track the new
high-water mark. Otherwise, we leave the pre-panic mbuf allocation alone.
In a future patch in this series, this will allow initiating netdump from
panic ddb(4) without pre-panic configuration.
No other functional change intended.
Reviewed by: markj (earlier version)
Some discussion with: emaste, jhb
Objection from: marius
Differential Revision: https://reviews.freebsd.org/D21421
Previously they were defined in a header which was included exactly
once. Change this to follow the usual practice of putting definitions
in C files. No functional change intended.
Discussed with: tuexen
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
This provides a framework to define a template describing
a set of "variables of interest" and the intended way for
the framework to maintain them (for example the maximum, sum,
t-digest, or a combination thereof). Afterwards the user
code feeds in the raw data, and the framework maintains
these variables inside a user-provided, opaque stats blobs.
The framework also provides a way to selectively extract the
stats from the blobs. The stats(3) framework can be used in
both userspace and the kernel.
See the stats(3) manual page for details.
This will be used by the upcoming TCP statistics gathering code,
https://reviews.freebsd.org/D20655.
The stats(3) framework is disabled by default for now, except
in the NOTES kernel (for QA); it is expected to be enabled
in amd64 GENERIC after a cool down period.
Reviewed by: sef (earlier version)
Obtained from: Netflix
Relnotes: yes
Sponsored by: Klara Inc, Netflix
Differential Revision: https://reviews.freebsd.org/D20477
MPFS is a logical switch in the Mellanox device which forward packets
based on a hardware driven L2 address table, to one or more physical-
or virtual- functions. The physical- or virtual- function is required
to tell the MPFS by using the MPFS firmware commands, which unicast
MAC addresses it is requesting from the physical port's traffic.
Broadcast and multicast traffic however, is copied to all listening
physical- and virtual- functions and does not need a rule in the MPFS
switching table.
Linux commit: eeb66cdb682678bfd1f02a4547e3649b38ffea7e
MFC after: 3 days
Sponsored by: Mellanox Technologies
is a completely separate TCP stack (tcp_bbr.ko) that will be built only if
you add the make options WITH_EXTRA_TCP_STACKS=1 and also include the option
TCPHPTS. You can also include the RATELIMIT option if you have a NIC interface that
supports hardware pacing, BBR understands how to use such a feature.
Note that this commit also adds in a general purpose time-filter which
allows you to have a min-filter or max-filter. A filter allows you to
have a low (or high) value for some period of time and degrade slowly
to another value has time passes. You can find out the details of
BBR by looking at the original paper at:
https://queue.acm.org/detail.cfm?id=3022184
or consult many other web resources you can find on the web
referenced by "BBR congestion control". It should be noted that
BBRv1 (which this is) does tend to unfairness in cases of small
buffered paths, and it will usually get less bandwidth in the case
of large BDP paths(when competing with new-reno or cubic flows). BBR
is still an active research area and we do plan on implementing V2
of BBR to see if it is an improvement over V1.
Sponsored by: Netflix Inc.
Differential Revision: https://reviews.freebsd.org/D21582
KTLS adds support for in-kernel framing and encryption of Transport
Layer Security (1.0-1.2) data on TCP sockets. KTLS only supports
offload of TLS for transmitted data. Key negotation must still be
performed in userland. Once completed, transmit session keys for a
connection are provided to the kernel via a new TCP_TXTLS_ENABLE
socket option. All subsequent data transmitted on the socket is
placed into TLS frames and encrypted using the supplied keys.
Any data written to a KTLS-enabled socket via write(2), aio_write(2),
or sendfile(2) is assumed to be application data and is encoded in TLS
frames with an application data type. Individual records can be sent
with a custom type (e.g. handshake messages) via sendmsg(2) with a new
control message (TLS_SET_RECORD_TYPE) specifying the record type.
At present, rekeying is not supported though the in-kernel framework
should support rekeying.
KTLS makes use of the recently added unmapped mbufs to store TLS
frames in the socket buffer. Each TLS frame is described by a single
ext_pgs mbuf. The ext_pgs structure contains the header of the TLS
record (and trailer for encrypted records) as well as references to
the associated TLS session.
KTLS supports two primary methods of encrypting TLS frames: software
TLS and ifnet TLS.
Software TLS marks mbufs holding socket data as not ready via
M_NOTREADY similar to sendfile(2) when TLS framing information is
added to an unmapped mbuf in ktls_frame(). ktls_enqueue() is then
called to schedule TLS frames for encryption. In the case of
sendfile_iodone() calls ktls_enqueue() instead of pru_ready() leaving
the mbufs marked M_NOTREADY until encryption is completed. For other
writes (vn_sendfile when pages are available, write(2), etc.), the
PRUS_NOTREADY is set when invoking pru_send() along with invoking
ktls_enqueue().
A pool of worker threads (the "KTLS" kernel process) encrypts TLS
frames queued via ktls_enqueue(). Each TLS frame is temporarily
mapped using the direct map and passed to a software encryption
backend to perform the actual encryption.
(Note: The use of PHYS_TO_DMAP could be replaced with sf_bufs if
someone wished to make this work on architectures without a direct
map.)
KTLS supports pluggable software encryption backends. Internally,
Netflix uses proprietary pure-software backends. This commit includes
a simple backend in a new ktls_ocf.ko module that uses the kernel's
OpenCrypto framework to provide AES-GCM encryption of TLS frames. As
a result, software TLS is now a bit of a misnomer as it can make use
of hardware crypto accelerators.
Once software encryption has finished, the TLS frame mbufs are marked
ready via pru_ready(). At this point, the encrypted data appears as
regular payload to the TCP stack stored in unmapped mbufs.
ifnet TLS permits a NIC to offload the TLS encryption and TCP
segmentation. In this mode, a new send tag type (IF_SND_TAG_TYPE_TLS)
is allocated on the interface a socket is routed over and associated
with a TLS session. TLS records for a TLS session using ifnet TLS are
not marked M_NOTREADY but are passed down the stack unencrypted. The
ip_output_send() and ip6_output_send() helper functions that apply
send tags to outbound IP packets verify that the send tag of the TLS
record matches the outbound interface. If so, the packet is tagged
with the TLS send tag and sent to the interface. The NIC device
driver must recognize packets with the TLS send tag and schedule them
for TLS encryption and TCP segmentation. If the the outbound
interface does not match the interface in the TLS send tag, the packet
is dropped. In addition, a task is scheduled to refresh the TLS send
tag for the TLS session. If a new TLS send tag cannot be allocated,
the connection is dropped. If a new TLS send tag is allocated,
however, subsequent packets will be tagged with the correct TLS send
tag. (This latter case has been tested by configuring both ports of a
Chelsio T6 in a lagg and failing over from one port to another. As
the connections migrated to the new port, new TLS send tags were
allocated for the new port and connections resumed without being
dropped.)
ifnet TLS can be enabled and disabled on supported network interfaces
via new '[-]txtls[46]' options to ifconfig(8). ifnet TLS is supported
across both vlan devices and lagg interfaces using failover, lacp with
flowid enabled, or lacp with flowid enabled.
Applications may request the current KTLS mode of a connection via a
new TCP_TXTLS_MODE socket option. They can also use this socket
option to toggle between software and ifnet TLS modes.
In addition, a testing tool is available in tools/tools/switch_tls.
This is modeled on tcpdrop and uses similar syntax. However, instead
of dropping connections, -s is used to force KTLS connections to
switch to software TLS and -i is used to switch to ifnet TLS.
Various sysctls and counters are available under the kern.ipc.tls
sysctl node. The kern.ipc.tls.enable node must be set to true to
enable KTLS (it is off by default). The use of unmapped mbufs must
also be enabled via kern.ipc.mb_use_ext_pgs to enable KTLS.
KTLS is enabled via the KERN_TLS kernel option.
This patch is the culmination of years of work by several folks
including Scott Long and Randall Stewart for the original design and
implementation; Drew Gallatin for several optimizations including the
use of ext_pgs mbufs, the M_NOTREADY mechanism for TLS records
awaiting software encryption, and pluggable software crypto backends;
and John Baldwin for modifications to support hardware TLS offload.
Reviewed by: gallatin, hselasky, rrs
Obtained from: Netflix
Sponsored by: Netflix, Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D21277
The netmap_pt.c module has become obsolete after
the refactoring that added netmap_kloop.c.
Remove it and unlink it from the build system.
MFC after: 1 week
Intel has created RST and many laptops from vendors like Lenovo and Asus. It's a
mechanism for creating multiple boot devices under windows. It effectively hides
the nvme drive inside of the ahci controller. The details are supposed to be a
trade secret. However, there's a reverse engineered Linux driver, and this
implements similar operations to allow nvme drives to attach. The ahci driver
attaches nvme children that proxy the remapped resources to the child. nvme_ahci
is just like nvme_pci, except it doesn't do the PCI specific things. That's
moved into ahci where appropriate.
When the nvme drive is remapped, MSI-x interrupts aren't forwarded (the linux
driver doesn't know how to use this either). INTx interrupts are used
instead. This is suboptimal, but usually sufficient for the laptops these parts
are in.
This is based loosely on https://www.spinics.net/lists/linux-ide/msg53364.html
submitted, but not accepted by, Linux. It was written by Dan Williams. These
changes were written from scratch by Olivier Houchard.
Submitted by: cognet@ (Olivier Houchard)
Nvme drives can be attached in a number of different ways. Separate out the PCI
attachment so that we can have other attachment types, like ahci and various
types of NVMeoF.
Submitted by: cognet@
Add helper function for synchronous execution of HCI commands at probe
stage and use this function to check firmware state of Intel Wireless
8260/8265 bluetooth devices found in many post 2016 year laptops.
Attempt to initialize FreeBSD bluetooth stack while such a device is in
bootloader mode locks the adapter hardly so it requires power on/off
cycle to restore.
This change blocks ng_ubt attachment unless operational firmware is
loaded thus preventing the lock up.
PR: 237083
Reviewed by: hps, emax
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D21071
The Zstd format bumps the CLOOP major number to 4 to avoid incompatibility
with older systems. Support in geom_uzip(4) is conditional on the ZSTDIO
kernel option, which is enabled in amd64 GENERIC, but not all in-tree
configurations.
mkuzip(8) was modified slightly to always initialize the nblocks + 1'th
offset in the CLOOP file format. Previously, it was only initialized in the
case where the final compressed block happened to be unaligned w.r.t.
DEV_BSIZE. The "Fake" last+1 block change in r298619 means that the final
compressed block's 'blen' was never correct unless the compressed uzip image
happened to be BSIZE-aligned. This happened in about 1 out of every 512
cases. The zlib and lzma decompressors are probably tolerant of extra trash
following the frame they were told to decode, but Zstd complains that the
input size is incorrect.
Correspondingly, geom_uzip(4) was modified slightly to avoid trashing the
nblocks + 1'th offset when it is known to be initialized to a good value.
This corrects the calculated final real cluster compressed length to match
that printed by mkuzip(8).
mkuzip(8) was refactored somewhat to reduce code duplication and increase
ease of adding other compression formats.
* Input block size validation was pulled out of individual compression
init routines into main().
* Init routines now validate a user-provided compression level or select
an algorithm-specific default, if none was provided.
* A new interface for calculating the maximal compressed size of an
incompressible input block was added for each driver. The generic code
uses it to validate against MAXPHYS as well as to allocate compression
result buffers in the generic code.
* Algorithm selection is now driven by a table lookup, to increase ease of
adding other formats in the future.
mkuzip(8) gained the ability to explicitly specify a compression level with
'-C'. The prior defaults -- 9 for zlib and 6 for lzma -- are maintained.
The new zstd default is 9, to match zlib.
Rather than select lzma or zlib with '-L' or its absense, respectively, a
new argument '-A <algorithm>' is provided to select 'zlib', 'lzma', or
'zstd'. '-L' is considered deprecated, but will probably never be removed.
All of the new features were documented in mkuzip.8; the page was also
cleaned up slightly.
Relnotes: yes
Follow-up on r322318 and r322319 and remove the deprecated modules.
Shift some now-unused kernel files into userspace utilities that incorporate
them. Remove references to removed GEOM classes in userspace utilities.
Reviewed by: imp (earlier version)
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D21249
with Communication Device Class Ethernet Emulation Model (CDC EEM).
The driver supports both the device, and host side operation; there
is a new USB template (#11) for the former.
This enables communication with virtual USB NIC provided by iLO 5,
as found in new HPE Proliant servers.
Reviewed by: hselasky
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Hewlett Packard Enterprise
Instances of the device can be configured using hints or FDT data.
Interfaces to reconfigure the chip and extract voltage measurements from
it are available via sysctl(8).
an updated rack depend on having access to the new
ratelimit api in this commit.
Sponsored by: Netflix Inc.
Differential Revision: https://reviews.freebsd.org/D20953
with an eventual goal to convert all legacl zlib callers to the new zlib
version:
* Move generic zlib shims that are not specific to zlib 1.0.4 to
sys/dev/zlib.
* Connect new zlib (1.2.11) to the zlib kernel module, currently built
with Z_SOLO.
* Prefix the legacy zlib (1.0.4) with 'zlib104_' namespace.
* Convert sys/opencrypto/cryptodeflate.c to use new zlib.
* Remove bundled zlib 1.2.3 from ZFS and adapt it to new zlib and make
it depend on the zlib module.
* Fix Z_SOLO build of new zlib.
PR: 229763
Submitted by: Yoshihiro Ota <ota j email ne jp>
Reviewed by: markm (sys/dev/zlib/zlib_kmod.c)
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D19706
The current implementation of gzipped a.out support was based
on a very old version of InfoZIP which ships with an ancient
modified version of zlib, and was removed from the GENERIC
kernel in 1999 when we moved to an ELF world.
PR: 205822
Reviewed by: imp, kib, emaste, Yoshihiro Ota <ota at j.email.ne.jp>
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D21099
o Add an experimental IOMMU support to xDMA framework
The BERI IOMMU device is the part of CHERI device-model project [1]. It
translates memory addresses for various BERI peripherals modelled in
software. It accepts FreeBSD/mips64 page directories format and manages
BERI TLB.
1. https://github.com/CTSRD-CHERI/device-model
Sponsored by: DARPA, AFRL
