was setup to do an abortive close an association that was
in the accept_queue could get stuck and never freed. Now
we properly start the kill timer on the socket and turn
off the flag (same thing we do for the graceful close method).
MFC after: 1 week
corruption bug where if an ATA command is issued before DMA is started,
data will become available to the controller before it knows what to do
with it. This results in either data corruption or a controller crash.
This patch remedies the problem by adopting the workaround employed
by Linux and Darwin: starting the DMA engine prior to sending the ATA
command.
Observer on: Xserve G5
Reviewed by: mav
MFC after: 1 week
the page is managed.
Don't set the machine-independent layer's dirty field for the page being
mapped in init_pte_prot(). (The dirty field is only supposed to set when
a mapping is removed or write-protected and the page was managed and
modified.)
Determine whether or not to perform dirty bit emulation based on whether
or not the page is managed, i.e., pageable, not based on whether the page
is being mapped into the kernel address space. Nearly all of the kernel
address space consists of unmanaged pages, so this has neglible impact on
the overhead of dirty bit emulation for the kernel address space. However,
there can also exist unmanaged pages in the user address space. Previously,
dirty bit emulation was unnecessarily performed on these pages.
Tested by: jchandra@
buffers it should also reinitialize RX descriptors otherwise some
stale data could be passed to controller. This could end up with
mbuf double free or unexpected NULL pointer dereference in upper
stack. To fix the issue, save loaded buffer's length and
reinitialize RX descriptors with the saved value whenever bge(4)
reuses the loaded RX buffers.
While I'm here, increase the number of RX buffers to 512 from 256.
This simplifies RX buffer handling as well as giving more RX
buffers. Controller supports just fixed number of RX buffers
(i.e. 512) and bge(4) used to rely on hope that our CPU is fast
enough to keep up with the controller. With this change, bge(4)
will use 1MB for RX buffers but I don't think it would cause
problems in these days.
Reported by: marcel
Tested by: marcel
1) Fix the alignment of a comment.
2) Fix a BUG where we were NOT paying attention
to the RESEND marking on retransmitting control
chunks.. and worse we were not decrementing the
retran count that could cause us to loop forever.
3) Add in the valdiate_no_lock function on invariants
so that we will really check all ways out to be sure
a lock does not slip out locked.
MFC after: 1 week.
1) Makes it so that the INVARIANT function validate nolocks is
available anywhere.
2) Fixes a BUG where a close has been done on a collision socket
and the cookie processing would return leaving a lock held.
MFC after: 1 week
fix. On Apple OpenPICs, the low/high bit of the interrupt sense is only
respected for interrupt 0. We currently erroneously program all OpenPIC
interrupts level high instead of level low by default, which only matters
for some G5 systems where the SATA controllers use IRQ 0.
This change is a quick fix that will be reverted once the effect of
changing the default interrupt sense on embedded systems is known.
MFC after: 3 days
are respected. This fixes loading the Apple onboard audio driver
(snd_ai2s) as a module after boot, which would previously cause a panic.
PR: powerpc/146888
MFC after: 5 days
context from in-kernel execution of padlock instructions and to handle
spurious FPUDNA exceptions that sometime are raised when doing padlock
calculations.
Globally mark crypto(9) kthread as using FPU.
Reviewed by: pjd
Hardware provided by: Sentex Communications
Tested by: pho
PR: amd64/135014
MFC after: 1 month
FPU/SSE hardware. Caller should provide a save area that is chained
into the stack of the areas; pcb save_area for usermode FPU state is
on top. The pcb now contains a pointer to the current FPU saved area,
used during FPUDNA handling and context switches. There is also a
facility to allow the kernel thread to use pcb save_area.
Change the dreaded warnings "npxdna in kernel mode!" into the panics
when FPU usage is not registered.
KPI discussed with: fabient
Tested by: pho, fabient
Hardware provided by: Sentex Communications
MFC after: 1 month
I don't know why- but it occurred to me in looking at the second sleep
is that all I want is a pause- not an actual sleep. So do that instead.
MFC after: 2 weeks
fails to allocate MIPS page table pages. The current usage of VM_WAIT in
case of vm_phys_alloc_contig() failure is not correct, because:
"There is no guarantee that any of the available free (or cached) pages
after the VM_WAIT will fall within the range of suitable physical
addresses. Every time this function sleeps and a single page is freed
(or cached) by someone else, this function will be reawakened. With
a little bad luck, you could spin indefinitely."
We also add low and high parameters to vm_contig_grow_cache() and
vm_contig_launder() so that we restrict vm_contig_launder() to the range
of pages we are interested in.
Reported by: alc
Reviewed by: alc
Approved by: rrs (mentor)
GCC forwards the -N flag directly to ld. This flag is not documented and
not supported by (for example) Clang. Just use -Wl,-N.
Submitted by: Pawel Worach
