uhci.c: -r1.82
uhcivar.h: -r1.22
date: 2000/01/26 10:04:39; author: augustss; state: Exp;
Try to avoid accessing the HC if it is dead. Suggested by mycroft.
revision 1.125
date: 2000/09/23 21:00:10; author: augustss; state: Exp; lines: +19 -3
Avoid "bandwidth reclamation" for control transfers. The kue device chokes
on it.
uhci.c: -r1.124
uhcireg.h: -r1.13
date: 2000/08/13 18:20:14; author: augustss; state: Exp;
Fix race condition when unlinking xfers. Thanks to IWAMOTO Toshihiro
<iwamoto@sat.t.u-tokyo.ac.jp> for analyzing the problem and suggesting a fix.
Fixes PR 10662.
uhci.c: -r1.123 (and a tiny bit of -r1.92)
uhcivar.h: -r1.32
date: 2000/08/13 16:18:09; author: augustss; state: Exp;
Implement what in Intel-speech is known as "bandwidth
reclamation". It means that we continously poll USB devices
that have a pending transfer instead of polling just once
every ms. This speeds up some transfers at the expense of
using more PCI bandwidth.
uchireg.h: -r1.12
uchi.c: -r1.121
date: 2000/07/23 19:43:38; author: augustss; state: Exp;
Be a little more explicit and careful about setting links in TDs and QHs.
date: 2000/02/29 21:37:01; author: augustss; state: Exp;
Distinguish between device and interface classes.
(I finally found a document that said that they were different.)
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
interrupt threads to run with it always >= 1, so that malloc can
detect M_WAITOK from "interrupt" context. This is also necessary
in order to context switch from sched_ithd() directly.
Reviewed By: peter
the offending inline function (BUF_KERNPROC) on it being #included
already.
I'm not sure BUF_KERNPROC() is even the right thing to do or in the
right place or implemented the right way (inline vs normal function).
Remove consequently unneeded #includes of <sys/proc.h>
cases the registers are not correctly set on resume.
This solves the problem of USB failing after resuming a machine.
Submitted by: mike+fbsd@medianstrip.net
PR: 18261
problem was basically (for offset > 4096):
vtophys(addr) + offset != vtophys(addr + offset)
Also, use TD's with a maximum size of 4k instead of 8kb for OHCI
controllers.
This problem occurs in drivers that use large transfer sizes:
umass, host2host and ethernet with jumbo frames.
uhci_check_intr() routine needs to be more careful about deciding when
the end of a transfer has been detected.
This allows me to remove the nasty workaround code from if_aue and if_cue.
Receive performance is now much better for these adapters (500KB/sec
vs. 350KB/sec).
Also removed unused KUE_CUTOFF define from if_kuereg.h.
Submitted by: Lennart Augustsson
Reviewed by: n_hibma
methods for USB devices.
However: with none of the devices I have here suspend seems to work
properly. This is probably a bug in uhci_power which I still have to
look at.
Prodded and pushed by: Christopher Masto <chris@netmonger.net>
- Sync ohci, uhci and usbdi modules with NetBSD in order to obtain the
following improvements:
o New USBD_NO_TSLEEP flag can be used in place of UQ_NO_TSLEEP
quirk. This allows drivers to specify busy waiting only for
certain transfers (namely control transfers for reading/writing
registers and stuff).
o New USBD_FORCE_SHORT_XFER flag can be used to deal with
devices like the ADMtek Pegasus that sense the end of bulk OUT
transfers in a special way (if a transfer is exactly a multiple
of 64 bytes in size, you need to send an extra empty packet
to terminate the transfer).
o usbd_open_pipe_intr() now accepts an interval argument which
can be used to change the rate at which the interrupt callback
routine is invoked. Specifying USBD_DEFAULT_INTERVAL uses the
value specified in the device's config data, but drivers can
override it if needed.
- Change if_aue to use USBD_FORCE_SHORT_XFER for packet transmissions.
- Change if_aue, if_kue and if_cue to use USBD_NO_TSLEEP for all
control transfers. We no longer force the non-tsleep hack for
bulk transfers since these are done asynchronously anyway.
- Removed quirk entry fiddling from if_aue and if_kue since we don't
need it anymore now that we have the USBD_NO_TSLEEP flag.
- Tweak ulpt, uhid, ums and ukbd drivers to use the new arg to
usbd_open_pipe_intr().
- Add a flag to the softc struct in the ethernet drivers to indicate
when a device has been detached, and use this flag to perform
tests to prevent the drivers from trying to do control transfers
if this is the case. This is necessary because calling if_detach()
with INET6 enabled will eventually result in a call to the driver's
ioctl() routine to delete the multicast groups on the interface,
which will result in attempts to perform control transfers. (It's
possible this also happens even without INET6 support enabled.) This
is pointless since we know that if the detach method has been called,
the hardware has been unplugged.
- Changed watchdog timeout routines to just call the driver init routines
to initialize the device states without trying to close and re-open the
pipes. This is partly because we don't want to frob things at interrupt
context, but also because this doesn't seem to work right and I don't
want to panic the system just because a USB device may have stopped
responding.
- Fix aue_rxeof() to be a little smarter about detecting when a double
transfer is needed. Unfortunately, the design of the chip makes it hard
to get this exactly right. Hopefully, this will go away once either
Nick or Lennart finds the bug in the uhci driver that makes this ugly
hack necessary.
- Also sync usbdevs with NetBSD.
- In uhci_intr() check to see if sc->sc_bus.bdev is NULL, and if it is,
ack any pending interrupts and disable them, then return. It is possible
for interrupts to be delivered the moment a handler is set up at attach
time in uhci_pci.c, particularly when attempting to kldload the usb.ko
module after the system is already up. However the driver isn't ready
to field interrupts at that time and certain pointers in the softc
struct aren't initialized yet, and we invariably end up falling off
the end of one of them. The effect is that kldloading the usb module
will panic the system in uhci_intr(). This added sanity check stops
this from happening: I can now kldload the usb.ko module without any
problems and load/attach other USB drivers after it.
Of course the uhci driver has no detach method, but that's another
problem.
- In uhci_run(), set the UHCI_CMD_MAXP bit in the command register to
allow 64-byte packets to be used for full speed bandwidth reclamation.
Certain high speed devices (in this case the ADMtek USB ethernet
adapter) require this bit to be set, otherwise babble errors occur
at the end of large (between 1100 and 1500 byte) transfers. This
should not affect other devices, although supposedly it is less efficient
than the 32-byte setting. Unfortunately, this is a per-bus setting,
not a per-device setting, so we can't just enable it for certain
devices on the USB bus.
are queued. Traverse the queues vertically and then horizontally.
This means that TDs for one xfer are transmitted back to back until the
first NAK or error condition. Up to now we transmitted a TD per frame
and transmitted the next TD in the next frame.
The old approach is more fair if you have the end of the queue point at
the beginning of the control transfer queue, but also a lot more overhead
due to the fact that the QHs have to be read more often.
The new approach squirts the packets down the line as fast as possible
for one transfer and then does the next one. In the current situation,
with fairly empty USB buses, this is a more sensible approach. We might
have to revisit the scheduler later however.
It speeds up large transfers (Zip drive, Host-To-Host adapters) on UHCI
by a factor of 5 and makes it as fast as OHCI on the bus.
The next problem to solve is the question why the limit is 300kb/s and
not 1000/kb/s (kb == kilobyte).
- more req[uest]->xfer changes.
- get the corresponding NetBSD Id's right
ohci.c
- move untimeout above print statement
- remove usb_delay that panics the system (tsleep in intr context) when
ohcidebug > 5.
ugen.c
- create the devices for endpoints with make_dev.
uhub.c
- change from using usbdebug to uhubdebug
- add more debugging statements
Cleaning up the code:
- Declare many functions static
- Change variable names to make them more self explanatory
- Change usbd_request_handle -> usbd_xfer_handle
- Syntactical changes
- Remove some unused code
- Other KNF changes
Interrupt context handling
- Change delay to usbd_delay_ms were possible (takes polling mode into
account)
- Change detection mechanism for interrupt context
Add support for pre-allocation DMA-able memory by device driver
Add preliminary support for isochronous to the UHCI driver (not for OHCI
yet).
usb.c, uhci.c, ohci.c
- Initial attempt at detachable USB host controllers
- Handle the use_polling flag with a lttle more care and only set it if
we are cold booting.
usb.c, uhci.c ohci.c, usbdi.c usbdi_util.c usb_subr.c
- Make sure an aborted pipe is marked as not running.
- Start queued request in the right order.
- Insert some more DIAGNOSTIC sanity checks.
- Remove (almost) unused definitions USBD_XFER_OUT and USBD_XFER_IN.
usb.c, usb_subr.c
- Add an event mechanism so that a userland process can watch devices
come and go.
ohci.c
- Handle the case when a USB transfer is so long that it crosses two
page (4K) boundaries. OHCI cannot do that with a single TD so we make
a chain.
ulpt.c
- Use a bigger buffer when transferring data.
- Pre-allocate the DMA buffer. This makes the driver slightly more
efficient.
- Comment out the GET_DEVICE_ID code, because for some unknown reason it
causes printing to fail sometimes.
usb.h
- Add a macro to extract the isoc type.
- Add a macro to check whether the routine has been entered after splusb
and if not, complain.
usbdi.c
- Fix a glitch in dequeueing and aborting requests on interrupt pipes.
- Add a flag in the request to determine if the data copying is done by
the driver or the usbdi layer.
condition for Short transfers.
Change the scheduling to Depth first. We now transfer as many TD's as
possible from QH before moving to the next queue (Breadth first). It should
still be verified that this does not lead to starvation in a busy system
(in the case were transfers are added to the beginning of the control
or bulk queues).
- Some cleanup and improvements in the uhci and ohci drivers
- Support for plugging and unplugging devices improved
- Now available is bulk transport over OHCI controllers
- Resume and suspend have been temporarily been disabled again. Proper
support for it is available in the uhci.c and ohci.c files but I have
not yet spent the brain cycles to use it.
- OpenBSD now uses the USB stack as well
- Add FreeBSD tags
of the current interrupt trasaction.
- Do not schedule the next interrupt transaction if the pipe is being
aborted or the last round of the interrupt transaction ended with error.
Submitted by: Kazutaka YOKOTA <yokota@zodiac.mech.utsunomiya-u.ac.jp>
resource. Avoids useless interrupts occurring between the allocation
of the interrupt resource and the final initialisation of the
kernel. Cause of these interrupts is unknown (a resuming device?).
2) rename variables to be more conclusive.
3) fix a problem in uhci_ii_done. Avoid collecting all the status's of the
TD's, we only need to one from the last inactive one.
4) Change the errorcount from 2 to 3 (see UHCI spec.).
i386 platform boots, it is no longer ISA-centric, and is fully dynamic.
Most old drivers compile and run without modification via 'compatability
shims' to enable a smoother transition. eisa, isapnp and pccard* are
not yet using the new resource manager. Once fully converted, all drivers
will be loadable, including PCI and ISA.
(Some other changes appear to have snuck in, including a port of Soren's
ATA driver to the Alpha. Soren, back this out if you need to.)
This is a checkpoint of work-in-progress, but is quite functional.
The bulk of the work was done over the last few years by Doug Rabson and
Garrett Wollman.
Approved by: core
2) create function usbd_errstr which turns a usbd_status into a sensible
error message
3) Change the printf in DPRINTF to logprintf which is a define for
log(KERN_DEBUG, x)
1) Removed 'emulation' of bitmaps in printfs, FreeBSD seems to have caught
up on that one
2) Fixed a few bugs in the timeout/timo timeout variables
3) First attempt at fixing a bug mentioned by Kazu: uhci_run is not able
start/stop his USB host on his motherboard.
