mode in the USB core. The patch mostly consists of updating the USB
HUB code to support USB 3.0 HUBs. This patch also add some more USB
controller methods to support more active-alike USB controllers like
the XHCI which needs to be informed about various device state events.
USB 3.0 HUBs are not tested yet, due to lack of hardware, but are
believed to work.
After this update the initial device descriptor is only read twice
when we know that the bMaxPacketSize is too small for a single packet
transfer of this descriptor.
Approved by: thompsa (mentor)
message has been printed is enough to get someones attention. Also remove the
line number for DPRINTF/DPRINTFN, it already prints the funtion name and a
unique message.
- clean up USB detach logic. There seems to be some problems detaching multiple
USB HUBs connected in series from the root.
- after this patch the rule is:
1) Always use device_detach() on the USB HUB first.
2) Never just device_delete_child() on the USB HUB, because that function
will traverse to all the device leaves and free them first, and then the USB
stack will free the devices twice which doesn't work very well.
- make sure the did DMA delay gets set after the timeout has elapsed to make
logic more clear. There is no functional difference.
Submitted by: Hans Petter Selasky
being polled.
- Remove the need for Giant from the USB HUB driver.
- Leave device unconfigured instead of disabling the USB port
when Huawei Autoinstall disk detection triggers. This should
fix problems that the Huawei device is not detected after
Autoinstall eject is issued.
- Reported by: Nikolay Antsiferov
- Fix memory use after free race for USB character devices.
- Reported by: Lucius Windschuh
- Factor out the enumeration lock into three functions to make the
coming newbus lock conversion more easy.
- usbd_enum_lock
- usbd_enum_unlock
- usbd_enum_is_locked
Submitted by: hps
- Add minimum polling support to drive UMASS
and UKBD in case of panic.
- Add extra check to ukbd probe to fix problem about
mouse devices attaching like keyboards.
- P4 ID: 166148
Submitted by: hps
Approved by: re
- Add support for devices that handle set and clear stall in hardware.
- Add missing get timestamp function
- Add more xfer flags
Submitted by: Hans Petter Selasky
Approved by: re (kib)
Some hardware easily comes out of sync with regard to whether the current or
the next control transfer should be stalled, if a stall command is always
issued before receiving the SETUP packet. After this patch the stall command
will only be issued when a transfer should actually be stalled.
Submitted by: Hans Petter Selasky
Refactor how we interface with the root HUB. This is achieved by making a
direct call from usb2_do_request to the host controller for root hub requests,
this call will perform the controller specific register read/writes and return
the error code.
This cuts out a lot of code in the host controller files and saves one thread
per USB bus.
Submitted by: Hans Petter Selasky
Some cancelable flags are always true. Substitute these away. These cancelable
flags were mostly useful with the root HUB which is now handled differently.
Submitted by: Hans Petter Selasky
Refactor how we interface with the root HUB. This cuts around 1200 lines of
code totally and saves one thread per USB bus.
Submitted by: Hans Petter Selasky
- make usb2_power_mask_t 16-bit
- remove "usb2_config_sub" structure from "usb2_config". To compensate for this
"usb2_config" has a new field called "usb_mode" which select for which mode
the current xfer entry is active. Options are: a) Device mode only b) Host
mode only (default-by-zero) c) Both modes. This change was scripted using
the following sed script: "s/\.mh\././g".
- the standard packet size table in "usb_transfer.c" is now a function, hence
the code for the function uses less memory than the table itself.
Submitted by: Hans Petter Selasky
Workaround for buggy USB hardware not handling new SETUP packet before STATUS
stage is complete, this allows xfers to endpoint0 to return a short frame.
Submitted by: Hans Petter Selasky
Reported by: me
- Move tunable defines into usb_core.h and dependancy towards usb_defs.h
- Leave hardcoded defines in "usb_defs.h".
- Allow overriding all tunable defines.
- Add more customisable typedefs.
- Correct maximum device number.
Submitted by: Hans Petter Selasky
Improvements to "usb2_transfer_setup()" and "usb2_transfer_unsetup()". Set
"ppxfer[n]" when the transfer setup is complete to prevent races. Remove
redundant NULL-checks from "usb2_transfer_unsetup()".
Submitted by: Hans Petter Selasky
