in here to do some conflict detection. The new code doesn't do conflict
detection yet, but it will be implemented in another way.
aic7770.c moved to i386/eisa
misplaced extern declarations (mostly prototypes of interrupt handlers)
that this exposed. The prototypes should be moved back to the driver
sources when the functions are staticalized.
Added idempotency guards to <machine/conf.h>. "ioconf.h" can't be
included when building LKMs so define a wart in bsd.kmod.mk to help
guard against including it.
/dev/random is now a part of the kernel! you will need to make
the device in /dev: sh MAKEDEV random
and take a look at some test code in src/tools/test/random.
the kernel. ppp_tty.c goes to some lengths to minimise the inter-layer
calling (including a soft ISR). ppp_tty.c takes care of the soft masking
that was needed still.
(I've discovered that bugs in this area show up within an hour if the
masking was not correct.. :-} This combination has proven stable on
specialix serial ports, although there was some concern about the softtty
parts of sio/cy and netisr colliding - but Bruce has fixed that now)
This code will only be included in your kernel if you have
'options DEVRANDOM', but that will fall away in a couple of days.
Obtained from: Theodore Ts'o, Linux
accesses after the BIOS bus scan. The previous revision made the assumption,
that every PCI motherboard did ...
Change the test on the initial value of the CONF1_ADDR_PORT register in a way
that makes the probe succeed on triton based motherboards, without breaking
the EISA motherboard that has some non-PCI register at the same address.
Require the state of the configuration enable bits to be OFF assuming
that the BIOS left them that way, as it should anyway to avoid bad things
to happen.
The tests themselves are copied from the previous release, with the
exception of CONF1_ENABLE_MSK1 having the LSB set. This bit should be
read back as '0', since only DWORD addresses are legal.
free-run and doing a subtract in microtime() rather than resetting the
counter to zero at every clock tick. In combination with the changes to
kern_clock.c, this should eliminate all the immediately obvious sources
of systematic jitter in timekeeping on Pentium machines.
option DDB_NO_LCALLS to stop ddb getting control and broke all ddb
tracing. Now there is no option and no way for ddb to trace at
address _Xsyscall or to _Xsyscall, but tracing everywhere else
works. The previous fix did unnecessary things for Linux syscalls.
Don't bother checking that syscall frames are for user mode.
Make debugger traps inside the kernel (except at addresses _Xsyscall
and _Xsyscall+1) fatal if ddb is not configured. They "can't happen".
Add prototypes.
Remove stupid comments, e.g., /*ARGSUSED*/ for args that are used.
Obtained from: other people on the net ?
1. stepping over syscalls (gdb ni) sends you to DDB, and returned
to the wrong address afterwards, with or without DDB. patch in
i386/i386/trap.c below.
2. the linux emulator (modload'ed) still causes panics with DIAGNOSTIC,
re-applied a patch posted to one of the lists...
Changes relative to 1.12:
- Put extra instruction between outl()/inl() sequence to prevent the
old value being read back because of the bus capacitance.
- Additional check for existence of register at CONF2_ENABLE_PORT.
setting the control register. Make the read and write operations two
completely separate steps.
While we're at it, pull in the whole set of Cyrix cache control options
from NetBSD-current, since a few motherboards do the right thing with
the Cyrix chip.
There is no option to disable the internal cache completely (yet).
Reviewed by: pst
Obtained from: NetBSD
EFAULT if it is not resident. This prevents the system from manufacturing
a zero-fill page for unused but allocated areas of the kernel's VM. This
should fix the "CMAP busy" panic that some people saw during system
startup.
there is a PCI bus at all) ...
- Do not expect the chip sets to follow even very clearly expressed
requirements of the PCI 2.0 spec.
- Do not read back the value just written to an I/O port without making
sure that some other data have crossed the bus in between ...
2) Killed i386pagesperpage as it is not used by anything.
3) Fixed benign miscalculations in pmap_bootstrap().
4) Moved allocation of ISA DMA memory to machdep.c.
5) Removed bogus vm_map_find()'s in pmap_init() - the entire range was
already allocated kmem_init().
6) Added some comments.
virual_avail is still miscalculated NKPT*NBPG too large, but in order to
fix this properly requires moving the variable initialization into locore.s.
Some other day.
used and went a long way toward confusing the code.
2) Fix proc0's initial stack to not be 48 bytes smaller than it needs to
be.
3) Correct comment about 'first' arg to init386().
the first one in the config has priority. They can be switched using
userconfig().
i386/i386/conf.c:
Initialize the shared syscons/pcvt cdevsw entry to `nx'.
Add cdevsw registration functions.
Use devsw functions of the correct type if they exist.
i386/i386/cons.c:
Add renamed syscons entry points to constab.
i386/i386/cons.h:
Declare the renamed syscons entry points.
i386/i386/machdep.c:
Repeat console initialization after userconfig() in case the current
console has become wrong. This depends on cn functions not wiring down
anything important.
sys/conf.h:
Declare new functions.
i386/isa/isa.[ch]:
Add a function to decide which display driver has priority. Should be
done better.
i386/isa/syscons.c:
Rename pccn* -> sccn*.
Initialize CRTC start address in case the previous driver has moved it.
i386/isa/syscons.c, i386/isa/pcvt/*
Initialize the bogusly shared variable Crtat dynamically in case the
stored value was changed by the previous driver.
Initialize cdevsw table from a template.
Don't grab the console if another display driver has priority.
i386/isa/syscons.h, i386/isa/pcvt/pcvt_hdr.h:
Don't externally declare now-static cdevsw functions.
i386/isa/pcvt/pcvt_hdr.h:
Set the sensitive hardware flag so that pcvt doesn't always have lower
priority than syscons. This also fixes the "stupid" detection of the
display after filling the display with text.
i386/isa/pcvt/pcvt_out.c:
Don't be confused the off-screen cursor offset 0xffff set by syscons.
kern/subr_xxx.c:
Add enough nxio/nodev/null devsw functions of the correct type for syscons
and pcvt.
Split off cdevsw initialization in cninit() into a new function
cninit_finish() that isn't called until all hardware device drivers
have been attached. The bdevsw entry of the driver for the physical
console needs to be hooked after the physical driver has been
attached in case the attachment modified the entry.
Rearrange cninit() to avoid changing cn_tab until the driver for the
physical console has been initialized, so that the previous driver
(if any) can be used for debugging.
Start removing half-baked lint support. bdevsw functions usually have
unused args but /*ARGSUSED*/ was used for only about 5% of them.
cons.h:
Declare cn_init_finish().
autoconf.c:
Call cn_init_finish().
Start adding prototypes. Functions with bogus linkage (extern where
static is probably should be static) are explicitly declared as extern
so that the can be found easily (extern in a non-header is usually
wrong).
All:
Continue cleaning up init stuff: init functions shall be static;
INITs should be at the start of files...
