It was used in bsnmpmap.c but was stored in bsnmptools.c; moving the extern
to the header allows us to cover all of our bases for the variable, and allows
_bsnmptools_debug to be used in the future elsewhere -- not just bsnmpmap.c.
MFC after: 3 weeks
Sponsored by: EMC / Isilon Storage Division
This has been compiling without warnings with clang/gcc for a while now
Tested with: clang 3.8.0, gcc 4.2.x, gcc 5.x
MFC after: 3 weeks
Sponsored by: EMC / Isilon Storage Division
* Add the siba bus phy/mac/bandwidth clock definitions (TGSLOW*)
* Add the PHY-N register gateway (BWN_PHY_N())
* Add the PHY-N TX phystat1 register - we need to actually fill out
more of the PHY encoding information when we assemble a frame.
* Various ancillary stuff
Nothing uses this yet, but I do have CCK/OFDM somewhat working
in 2GHz mode on a PHY-N device.
Obtained from: b43 (definitions)
may make Coverity think that other negative values of cmd (used
as an index) are possible. Testing < 0 is a more common idiom
in any case.
Reported by: Coverity
CID: 1305629
These firmwares were obtained from the "Chelsio T5/T4 Unified Wire
v2.12.0.3 for Linux" release. Changes since 1.14.4.0 (which is the
firmware in -STABLE branches) are in the "Release Notes" accompanying
the Unified Wire release and are copy-pasted here as well.
22.1. T5 Firmware
+++++++++++++++++++++++++++++++++
Version : 1.15.37.0
Date : 04/27/2016
================================================================================
FIXES
-----
BASE:
- Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where the default ingress
queue was ignored.
- Fixed an issue where adapter failed to load fw by adjusting DRAM frequency.
- Fixed an issue in watchdog which was causing VM bring-up failure after reboot.
- Fixed 40G link failures with some switches when auto-negotiation enabled.
- Fixed to improve on link bring-up time.
- Per port buffer groups size doubled to improve performance.
- Fixed an issue where bogus d3hot bits were set causing traffic stall.
- Fixed an issue where sometimes adapter was not seen after reboot.
- Fixed an issue where iWARP was crashing in conjunction with traffic management.
- Fixed an issue where link failed to come up after removing twinax cable and
inserting optical module.
ETH
- Fixed a link flap issue on T580-CR.
OFLD
- Fixed a potential iSCSI data corruption issue by disabling RxFragEn flag.
FOiSCSI
- Fixed an issue in recovery path where connection was getting closed before
recovery processing was done.
- Fixed an issue in TCP port reuse.
- Fixed an issue in recovery path when large number (>64) of iSCSI connections
were in use.
- Returned ENETUNREACH if IP was not been provisioned yet and driver tried to
use given inerface.
- Fixed an issue where fw was sending ENETUNREACH event for normal tcp
disconnection.
DCBX
- Fixed an issue where iscsi tlv is sent incorrectly to host. (DCBX CEE)
- Fixed an issue where apply bit set for APP id was affecting the ETS and PFC
settings.(DCBX IEEE)
- Fixed an issue where app priority values are not handled correctly in fw.
(DCBX IEEE)
- Fixed an issue where enable/disable dcbx can cause crash. (DCBX CEE,DCBX IEEE)
FOFCoE
- Removed BB6 support.
ENHANCEMENTS
------------
BASE:
- Added new interface to program DCA settings in SGE contexts; allow 32-byte
IQE size
- Added PTP interface fw_ptp_ts to support PTP Frequeny and Offset adjustment.
- Added MPS raw interface.
ETH:
- New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx.
OFLD:
- WR opcode is returned to host in cqe error response.
22.2. T4 Firmware
+++++++++++++++++
Version : 1.15.37.0
Date : 04/27/2016
================================================================================
FIXES
-----
BASE:
- Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where default ingress queue
was ignored.
- Fixed an issue in watchdog which was causing VM bring-up failure after reboot.
- Per port buffer groups size doubled to improve performance.
- Fixed an issue where iWARP was crashing in conjunction with traffic management.
FOiSCSI:
- Fixed an issue in recovery path where connection was getting closed before
recovery processing was done.
- Fixed an issue in TCP port reuse.
- Fixed an issue in recovery path when large number (>64) of iSCSI connections
were in use.
- Returned ENETUNREACH if IP had not been provisioned yet and driver tried to
use given inerface.
DCBX
- Fixed an issue where iscsi tlv is sent incorrectly to host.(DCBX CEE)
- Fixed an issue where enable/disable dcbx can cause crash in firmware.(DCBX CEE)
FOiSCSI
- Fixes an issue where fw was sending ENETUNREACH event for normal tcp
disconnection.
FOFCoE
- Removed BB6 support.
ENHANCEMENTS
------------
BASE:
- Added MPS raw interface.
ETH:
- New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx.
================================================================================
Obtained from: Chelsio Communications
MFC after: 6 weeks
Relnotes: yes
Sponsored by: Chelsio Communications
disabled, however when we enable it it will default to assume memory is
not cache-coherent, unless either the tag was created or the parent was
marked as cache-coherent.
Obtained from: ABT Systems Ltd
Relnotes: yes
Sponsored by: The FreeBSD Foundation
if specific CPU features are not present.
Some simulation environments, e.g. gem5, have been found to require more
TLB management from the kernel in certain setups. It is currently unclear why.
Turning on the workaround_erratum383 seems to help and make problems (panics)
go away.
Given this is a fairly uncommon environment so far, allowing the workaround
to be manually enabled from loader in order to make debugging and comparing
traces easier, but also to allow gem5 run FreeBSD in X86 timing mode, seems
to be the least intrusive option for now until the issue if fully understood.
Sponsored by: DARPA/AFRL
Reviewed by: kib, alc (earlier)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D6206
NOTE:
The FreeBSD system currently restricts the MAX IO size to MAXPHYS which
in turn is 128KB. We tested the 1MB IO by converting the MAXPHYS to 1MB.
Following is the mail reference:
http://lists.freebsd.org/pipermail/freebsd-scsi/2015-January/006568.html
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: AVAGO Technologies
JBODs. Driver has to sync the JBOD map with firmware and use sequence number
as a reference for JBOD FastPath I/O's.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: AVAGO Technologies
which leads to end being before start and thus a signed extended very large
number of size later on, which kva_alloc() will fail upon and we will panic.
Add the missing call.
Debugged with: andrew
Reviewed by: br, andrew
Sponsored by: DARPA/AFRL
Found: while using virtio with gem5
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D6337
streamline the rest of the xxx_to_jiffies() functions to have a
constant 64-bit argument and use identical range checks for the
result.
Specifically preserve msecs_to_jiffies(0) returning 0. See r282743 for
further details.
MFC after: 1 week
Sponsored by: Mellanox Technologies
- Use fgetln instead of fgets; localize complexity related to fgetln(3)
inside the loop.
- Skip over blank lines.
- Skip over lines (properly) that start with a "#"
MFC after: 1 week
Sponsored by: EMC / Isilon Storage Division
error code checks might fail. ERESTART is in the BSD world defined as
-1. While at it add more Linux error codes.
Obtained from: kmacy @
MFC after: 1 week
Sponsored by: Mellanox Technologies
There was the requirement that two structures are in sync,
which is not valid anymore. Therefore don't rely on this
in the code anymore.
Thanks to Radek Malcic for reporting the issue. He found this
when using the userland stack.
MFC after: 1 week
Falcon support has been removed, so this code only supports Siena.
Submitted by: Andy Moreton <amoreton at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Falcon support has been removed, so this code only supports Siena.
Submitted by: Andy Moreton <amoreton at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Falcon support has been removed, so this code only supports Siena.
Submitted by: Andy Moreton <amoreton at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Falcon support has been removed, so this code only supports Siena.
Reviewed by: Andy Moreton <amoreton at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
