le*dec / le*enc functions.
Replace net80211 specific macros with system-wide bytestream
encoding/decoding functions:
- LE_READ_2 -> le16dec
- LE_READ_4 -> le32dec
- LE_WRITE_2 -> le16enc
- LE_WRITE_4 -> le32enc
+ drop ieee80211_input.h include, where it was included for these
operations only.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D6030
* Don't use arbitrary frames for the average RX RSSI - only frames
from the current BSSID
* Don't log / do the syncbeacon logic for another BSSID and definitely
don't do the syncbeacon call if we miss beacons outside of STA mode.
* Don't do the IBSS merge bits if the current node plainly won't ever
match our current BSS (ie, the IBSS doesn't have to match, but all
the same bits that we check in ieee80211_ibss_merge() have to match.)
Tested:
* ath(4), AR9380, IBSS mode, surrounded by a lot of IBSS 11ac networks.
Sponsored by: Eva Automation, Inc.
I added MYBEACON support a while ago to listen to beacons that are only
for your configured BSSID. For AR9380 and later NICs this results in
a lot less chip wakeups in station mode as it then only shows you beacons
that are destined to you.
However in IBSS mode you really do want to hear all beacons so you can do
IBSS merges. Oops.
So only use MYBEACON for STA + not-scanning, and just use BEACON for
the other modes it used to use BEACON for.
This doesn't completely fix IBSS merges though - there are still some
conditions to chase down and fix.
This should be a big no-op pass; and reduces the size of if_ath.c.
I'm hopefully soon going to take a whack at the USB support for ath(4)
and this'll require some reuse of the busdma memory code.
connectivity interact with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to pluknet@, Oliver Hartmann,
Olivier Cochard, gjb@, mmoll@, op@ and lev@, who also participated in
testing.
Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
* 286410
* 286413
* 286416
The initial commit broke a variety of debug and features that aren't
in the GENERIC kernels but are enabled in other platforms.
with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to Olivier Cochard, gjb@, mmoll@,
op@ and lev@, who also participated in testing. Details here:
https://wiki.freebsd.org/projects/ifnet/net80211
Still, drivers: ndis, wtap, mwl, ipw, bwn, wi, upgt, uath were not
tested. Changes to mwl, ipw, bwn, wi, upgt are trivial and chances
of problems are low. The wtap wasn't compilable even before this change.
But the ndis driver is complex, and it is likely to be broken with this
commit. Help with testing and debugging it is appreciated.
Differential Revision: D2655, D2740
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
Smart NICs with firmware (eg wpi, iwn, the new atheros parts, the intel 7260
series, etc) support doing a lot of things in firmware. This includes but
isn't limited to things like scanning, sending probe requests and receiving
probe responses. However, net80211 doesn't know about any of this - it still
drives the whole scan/probe infrastructure itself.
In order to move towards suppoting smart NICs, the receive path needs to
know about the channel/details for each received packet. In at least
the iwn and 7260 firmware (and I believe wpi, but I haven't tried it yet)
it will do the scanning, power-save and off-channel buffering for you -
all you need to do is handle receiving beacons and probe responses on
channels that aren't what you're currently on. However the whole receive
path is peppered with ic->ic_curchan and manual scan/powersave handling.
The beacon parsing code also checks ic->ic_curchan to determine if the
received beacon is on the correct channel or not.[1]
So:
* add freq/ieee values to ieee80211_rx_stats;
* change ieee80211_parse_beacon() to accept the 'current' channel
as an argument;
* modify the iv_input() and iv_recv_mgmt() methods to include the rx_stats;
* add a new method - ieee80211_lookup_channel_rxstats() - that looks up
a channel based on the contents of ieee80211_rx_stats;
* if it exists, use it in the mgmt path to switch the current channel
(which still defaults to ic->ic_curchan) over to something determined
by rx_stats.
This is enough to kick-start scan offload support in the Intel 7260
driver that Rui/I are working on. It also is a good start for scan
offload support for a handful of existing NICs (wpi, iwn, some USB
parts) and it'll very likely dramatically improve stability/performance
there. It's not the whole thing - notably, we don't need to do powersave,
we should not scan all channels, and we should leave probe request sending
to the firmware and not do it ourselves. But, this allows for continued
development on the above features whilst actually having a somewhat
working NIC.
TODO:
* Finish tidying up how the net80211 input path works.
Right now ieee80211_input / ieee80211_input_all act as the top-level
that everything feeds into; it should change so the MIMO input routines
are those and the legacy routines are phased out.
* The band selection should be done by the driver, not by the net80211
layer.
* ieee80211_lookup_channel_rxstats() only determines 11b or 11g channels
for now - this is enough for scanning, but not 100% true in all cases.
If we ever need to handle off-channel scan support for things like
static-40MHz or static-80MHz, or turbo-G, or half/quarter rates,
then we should extend this.
[1] This is a side effect of frequency-hopping and CCK modes - you
can receive beacons when you think you're on a different channel.
In particular, CCK (which is used by the low 11b rates, eg beacons!)
is decodable from adjacent channels - just at a low SNR.
FH is a side effect of having the hardware/firmware do the frequency
hopping - it may pick up beacons transmitted from other FH networks
that are in a different phase of hopping frequencies.
used.
It turns out that the RX DMA engine does the same last-descriptor-link-
pointer-re-reading trick that the TX DMA engine. That is, the hardware
re-reads the link pointer before it moves onto the next descriptor.
Thus we can't free a descriptor before we move on; it's possible the
hardware will need to re-read the link pointer before we overwrite
it with a new one.
Tested:
* AR5416, STA mode
TODO:
* more thorough AP and STA mode testing!
* test on other pre-AR9380 NICs, just to be sure.
* Break out the RX descriptor grabbing bits from the RX completion
bits, like what is done in the RX EDMA code, so ..
* .. the RX lock can be held during ath_rx_proc(), but not across
packet input.
fixes and beacon programming / debugging into the ath(4) driver.
The basic power save tracking:
* Add some new code to track the current desired powersave state; and
* Add some reference count tracking so we know when the NIC is awake; then
* Add code in all the points where we're about to touch the hardware and
push it to force-wake.
Then, how things are moved into power save:
* Only move into network-sleep during a RUN->SLEEP transition;
* Force wake the hardware up everywhere that we're about to touch
the hardware.
The net80211 stack takes care of doing RUN<->SLEEP<->(other) state
transitions so we don't have to do it in the driver.
Next, when to wake things up:
* In short - everywhere we touch the hardware.
* The hardware will take care of staying awake if things are queued
in the transmit queue(s); it'll then transit down to sleep if
there's nothing left. This way we don't have to track the
software / hardware transmit queue(s) and keep the hardware
awake for those.
Then, some transmit path fixes that aren't related but useful:
* Force EAPOL frames to go out at the lowest rate. This improves
reliability during the encryption handshake after 802.11
negotiation.
Next, some reset path fixes!
* Fix the overlap between reset and transmit pause so we don't
transmit frames during a reset.
* Some noisy environments will end up taking a lot longer to reset
than normal, so extend the reset period and drop the raise the
reset interval to be more realistic and give the hardware some
time to finish calibration.
* Skip calibration during the reset path. Tsk!
Then, beacon fixes in station mode!
* Add a _lot_ more debugging in the station beacon reset path.
This is all quite fluid right now.
* Modify the STA beacon programming code to try and take
the TU gap between desired TSF and the target TU into
account. (Lifted from QCA.)
Tested:
* AR5210
* AR5211
* AR5212
* AR5413
* AR5416
* AR9280
* AR9285
TODO:
* More AP, IBSS, mesh, TDMA testing
* Thorough AR9380 and later testing!
* AR9160 and AR9287 testing
Obtained from: QCA
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
The AR9485 chip and AR933x SoC both implement LNA diversity.
There are a few extra things that need to happen before this can be
flipped on for those chips (mostly to do with setting up the different
bias values and LNA1/LNA2 RSSI differences) but the first stage is
putting this code into the driver layer so it can be reused.
This has the added benefit of making it easier to expose configuration
options and diagnostic information via the ioctl API. That's not yet
being done but it sure would be nice to do so.
Tested:
* AR9285, with LNA diversity enabled
* AR9285, with LNA diversity disabled in EEPROM
the RX antenna field.
The AR9285/AR9485 use an LNA mixer to determine how to combine the signals
from the two antennas. This is encoded in the RSSI fields (ctl/ext) for
chain 2. So, let's use that here.
This maps RX antennas 0->3 to the RX mixer configuration used to
receive a frame. There's more that can be done but this is good enough
to diagnose if the hardware is doing "odd" things like trying to
receive frames on LNA2 (ie, antenna 2 or "alt" antenna) when there's
only one antenna connected.
Tested:
* AR9285, STA mode
buffers (ie, >4GB on amd64.)
The underlying problem was that PREREAD doesn't sync the mbuf
with the DMA memory (ie, bounce buffer), so the bounce buffer may
have had stale information. Thus it was always considering the
buffer completed and things just went off the rails.
This change does the following:
* Make ath_rx_pkt() always consume the mbuf somehow; it no longer
passes error mbufs (eg CRC errors, crypt errors, etc) back up
to the RX path to recycle. This means that a new mbuf is always
allocated each time, but it's cleaner.
* Push the RX buffer map/unmap to occur in the RX path, not
ath_rx_pkt(). Thus, ath_rx_pkt() now assumes (a) it has to consume
the mbuf somehow, and (b) that it's already been unmapped and
synced.
* For the legacy path, the descriptor isn't mapped, it comes out of
coherent, DMA memory anyway. So leave it there.
* For the EDMA path, the RX descriptor has to be cleared before
its passed to the hardware, so that when we check with
a POSTREAD sync, we actually get either a blank (not finished)
or a filled out descriptor (finished.) Otherwise we get stale
data in the DMA memory.
* .. so, for EDMA RX path, we need PREREAD|PREWRITE to sync the
data -> DMA memory, then POSTREAD|POSTWRITE to finish syncing
the DMA memory -> data.
* Whilst we're here, make sure that in EDMA buffer setup (ie,
bzero'ing the descriptor part) is done before the mbuf is
map/synched.
NOTE: there's been a lot of commits besides this one with regards to
tidying up the busdma handling in ath(4). Please check the recent
commit history.
Discussed with and thanks to: scottl
Tested:
* AR5416 (non-EDMA) on i386, with the DMA tag for the driver
set to 2^^30, not 2^^32, STA
* AR9580 (EDMA) on i386, as above, STA
* User - tested AR9380 on amd64 with 32GB RAM.
PR: kern/177530
"complete RX frames."
The 128 entry RX FIFO is really easy to fill up and miss refilling
when it's done in the ath taskq - as that gets blocked up doing
RX completion, TX completion and other random things.
So the 128 entry RX FIFO now gets emptied and refilled in the ath_intr()
task (and it grabs / releases locks, so now ath_intr() can't just be
a FAST handler yet!) but the locks aren't held for very long. The
completion part is done in the ath taskqueue context.
Details:
* Create a new completed frame list - sc->sc_rx_rxlist;
* Split the EDMA RX process queue into two halves - one that
processes the RX FIFO and refills it with new frames; another
that completes the completed frame list;
* When tearing down the driver, flush whatever is in the deferred
queue as well as what's in the FIFO;
* Create two new RX methods - one that processes all RX queues,
one that processes the given RX queue. When MSI is implemented,
we get told which RX queue the interrupt came in on so we can
specifically schedule that. (And I can do that with the non-MSI
path too; I'll figure that out later.)
* Convert the legacy code over to use these new RX methods;
* Replace all the instances of the RX taskqueue enqueue with a call
to a relevant RX method to enqueue one or all RX queues.
Tested:
* AR9380, STA
* AR9580, STA
* AR5413, STA
* a flags field that lets me know what's going on;
* the hardware ratecode, unmolested by conversion to a bitrate;
* the HAL rs_flags field, useful for debugging;
* specifically mark aggregate sub-frames.
This stuff sorely needs tidying up - it's missing some important
stuff (eg numdelims) and it would be nice to put the flags at the
beginning rather than at the end.
Tested:
* AR9380, STA mode, 2x2 HT40, monitoring RSSI and EVM values
actually do have to reinitialise the RX side of things after an RX
descriptor EOL error.
* Revert a change of mine from quite a while ago - don't shortcut the
RX initialisation path. There's a RX FIFO bug in the earlier chips
(I'm not sure when it was fixed in this series, but it's fixed
with the AR9380 and later) which causes the same RX descriptor to
be written to over and over. This causes the descriptor to be
marked as "done", and this ends up causing the whole RX path to
go very strange. This should fixed the "kickpcu; handled X packets"
message spam where "X" is consistently small.
Right now, ic_curchan seems to be updated rather quickly (ie, during
the ioctl) and before the driver gets notified of what's going on.
So what I was seeing was:
* NIC was in channel X;
* It generates PHY errors for channel X;
* an ioctl comes along from userland and changes things to channel Y;
* .. this updates ic_curchan, but hasn't yet reset the hardware;
* in parallel, RX is occuring and it looks at ic_curchan;
* .. which is channel Y, so events get stamped with that now.
Sigh.
* upon setup, tell the alq code what the chip information is.
* add TX/RX path logging for legacy chips.
* populate the tx/rx descriptor length fields with a best-estimate.
It's overly big (96 bytes when AH_SUPPORT_AR5416 is enabled)
but it'll do for now.
Whilst I'm here, add CURVNET_RESTORE() here during probe/attach as a
partial solution to fixing crashes during attach when the attach fails.
There are other attach failures that I have to deal with; those'll come
later.
events.
This is primarily for the TX EDMA and TX EDMA completion. I haven't yet
tied it into the EDMA RX path or the legacy TX/RX path.
Things that I don't quite like:
* Make the pointer type 'void' in ath_softc and have if_ath_alq*()
return a malloc'ed buffer. That would remove the need to include
if_ath_alq.h in if_athvar.h.
* The sysctl setup needs to be cleaned up.
Right now processing a full 512 frame queue takes quite a while (measured
on the order of milliseconds.) Because of this, the TX processing ends up
sometimes preempting the taskqueue:
* userland sends a frame
* it goes in through net80211 and out to ath_start()
* ath_start() will end up either direct dispatching or software queuing a
frame.
If TX had to wait for RX to finish, it would add quite a few ms of
additional latency to the packet transmission. This in the past has
caused issues with TCP throughput.
Now, as part of my attempt to bring sanity to the TX/RX paths, the first
step is to make the RX processing happen in smaller 'parts'. That way
when TX is pushed into the ath taskqueue, there won't be so much latency
in the way of things.
The bigger scale change (which will come much later) is to actually
process the frames in the ath_intr taskqueue but process _frames_ in
the ath driver taskqueue. That would reduce the latency between
processing and requeuing new descriptors. But that'll come later.
The actual work:
* Add ATH_RX_MAX at 128 (static for now);
* break out of the processing loop if npkts reaches ATH_RX_MAX;
* if we processed ATH_RX_MAX or more frames during the processing loop,
immediately reschedule another RX taskqueue run. This will handle
the further frames in the taskqueue.
This should have very minimal impact on the general throughput case,
unless the scheduler is being very very strange or the ath taskqueue
ends up spending a lot of time on non-RX operations (such as TX
completion.)
This should eventually be unified with ATH_DEBUG() so I can get both
from one macro; that may take some time.
Add some new probes for TX and TX completion.
The AR9300 and later descriptors are 128 bytes, however I'd like to make
sure that isn't used for earlier chips.
* Populate the TX descriptor length field in the softc with
sizeof(ath_desc)
* Use this field when allocating the TX descriptors
* Pre-AR93xx TX/RX descriptors will use the ath_desc size; newer ones will
query the HAL for these sizes.
The AR9003 series NICs implement a separate RX error to signal that a
Keycache miss occured. The earlier NICs would not set the key index
valid bit.
I'll dig into the difference between "no key index bit set" and "keycache
miss".
The AR93xx and later chips support two RX FIFO queues - a high and low
priority queue.
For legacy chips, just assume the queues are high priority.
This is inspired by the reference driver but is a reimplementation of
the API and code.
The RX EDMA support requires a modified approach to the RX descriptor
handling.
Specifically:
* There's now two RX queues - high and low priority;
* The RX queues are implemented as FIFOs; they're now an array of pointers
to buffers;
* .. and the RX buffer and descriptor are in the same "buffer", rather than
being separate.
So to that end, this commit abstracts out most of the RX related functions
from the bulk of the driver. Notably, the RX DMA/buffer allocation isn't
updated, primarily because I haven't yet fleshed out what it should look
like.
Whilst I'm here, create a set of matching but mostly unimplemented EDMA
stubs.
Tested:
* AR9280, station mode
TODO:
* Thorough AP and other mode testing for non-EDMA chips;
* Figure out how to allocate RX buffers suitable for RX EDMA, including
correctly setting the mbuf length to compensate for the RX descriptor
and completion status area.
a buffer pointer.
For large radar pulses, the AR9130 and later will return a series of
FFT results for software processing. These can overflow a single 2KB
buffer on longer pulses. This would result in undefined buffer behaviour.
This includes a few new fields in each RXed frame:
* per chain RX RSSI (ctl and ext);
* current RX chainmask;
* EVM information;
* PHY error code;
* basic RX status bits (CRC error, PHY error, etc).
This is primarily to allow me to do some userland PHY error processing
for radar and spectral scan data. However since EVM and per-chain RSSI
is provided, others may find it useful for a variety of tasks.
The default is to not compile in the radiotap vendor extensions, primarily
because tcpdump doesn't seem to handle the particular vendor extension
layout I'm using, and I'd rather not break existing code out there that
may be (badly) parsing the radiotap data.
Instead, add the option 'ATH_ENABLE_RADIOTAP_VENDOR_EXT' to your kernel
configuration file to enable these options.
called to "kick" along TX.
For now, schedule a taskqueue call.
Later on I may go back to the direct call of ath_rx_tasklet() - but for
now, this will do.
I've tested UDP and TCP TX. UDP TX still achieves 240MBit, but TCP
TX gets stuck at around 100MBit or so, instead of the 150MBit it should
be at. I'll re-test with no ACPI/power/sleep states enabled at startup
and see what effect it has.
This is in preparation for supporting an if_transmit() path, which will
turn ath_tx_kick() into a NUL operation (as there won't be an ifnet
queue to service.)
Tested:
* AR9280 STA
TODO:
* test on AR5416, AR9160, AR928x STA/AP modes
PR: kern/168649
implementing parallel TX and TX/RX completion can be done without
simply abusing long-held locks.
Right now, multiple concurrent ath_start() entries can result in
frames being dequeued out of order. Well, they're dequeued in order
fine, but if there's any preemption or race between CPUs between:
* removing the frame from the ifnet, and
* calling and runningath_tx_start(), until the frame is placed on a
software or hardware TXQ
Then although dequeueing the frame is in-order, queueing it to the hardware
may be out of order.
This is solved in a lot of other drivers by just holding a TX lock over
a rather long period of time. This lets them continue to direct dispatch
without races between dequeue and hardware queue.
Note to observers: if_transmit() doesn't necessarily solve this.
It removes the ifnet from the main path, but the same issue exists if
there's some intermediary queue (eg a bufring, which as an aside also
may pull in ifnet when you're using ALTQ.)
So, until I can sit down and code up a much better way of doing parallel
TX, I'm going to leave the TX path using a deferred taskqueue task.
What I will likely head towards is doing a direct dispatch to hardware
or software via if_transmit(), but it'll require some driver changes to
allow queues to be made without using the really large ath_buf / ath_desc
entries.
TODO:
* Look at how feasible it'll be to just do direct dispatch to
ath_tx_start() from if_transmit(), avoiding doing _any_ intermediary
serialisation into a global queue. This may break ALTQ for example,
so I have to be delicate.
* It's quite likely that I should break up ath_tx_start() so it
deposits frames onto the software queues first, and then only fill
in the 802.11 fields when it's being queued to the hardware.
That will make the if_transmit() -> software queue path very
quick and lightweight.
* This has some very bad behaviour when using ACPI and Cx states.
I'll do some subsequent analysis using KTR and schedgraph and file
a follow-up PR or two.
PR: kern/168649
