* the descriptor ID, and
* the multi-buffer support that the EDMA chips support.
This is required for successful MAC transmission of multi-descriptor
frames. The MAC simply hangs if there are NULL buffers + 0 length pointers,
but the descriptor did have TxMore set.
This won't be done for the 11n aggregate path, as that will be modified
to use the newer API (ie, ath_hal_filltxdesc() and then set first|middle|
last_aggr), which will deprecate some of the current code.
TODO:
* Populate the numTxMaps field in the HAL, then make sure that's fetched
by the driver. Then I can undo that hack.
Tested:
* AR9380, AP mode, TX'ing non-aggregate 802.11n frames;
* AR9280, STA/AP mode, doing aggregate and non-aggregate traffic.
This is required to support > MCS15 as more than 32 bit rate entries are
suddenly available.
This is quite messy - instead of doing typecasts at each mask operation,
this should be migrated to use a macro and have that do the typecast.
r233822:
Remove useless and wrong piece of code in fdt_get_range() which i
overwrites passed phandle_t node. Modify debug printf in fdt_reg_to_rl()
to be consistent (that is, print start and end *virtual* addresses).
r230560:
Handle "ranges;"
Make fdt_reg_to_rl() responsible for mapping the device memory, instead
on just hoping that there's only one simplebus, and using fdt_immr_va as
the base VA.
r230315
Add a function to get the PA from range, instead of (ab)using
fdt_immr_pa, and use it for the UART driver
r238211:
Support TARGET_ARCH=armv6 and TARGET_ARCH=armv6eb
This adds a new TARGET_ARCH for building on ARM
processors that support the ARMv6K multiprocessor
extensions. In particular, these processors have
better support for TLS and mutex operations.
This mostly touches a lot of Makefiles to extend
existing patterns for inferring CPUARCH from ARCH.
It also configures:
* GCC to default to arm1176jz-s
* GCC to predefine __FreeBSD_ARCH_armv6__
* gas to default to ARM_ARCH_V6K
* uname -p to return 'armv6'
* make so that MACHINE_ARCH defaults to 'armv6'
It also changes a number of headers to use
the compiler __ARM_ARCH_XXX__ macros to configure
processor-specific support routines.
Submitted by: Tim Kientzle <kientzle@freebsd.org>
Cummulative patch of changes that are not vendor-specific:
- ARMv6 and ARMv7 architecture support
- ARM SMP support
- VFP/Neon support
- ARM Generic Interrupt Controller driver
- Simplification of startup code for all platforms
interface's MTU. Initialize such freelists with correct values.
This wasn't a problem for common MTUs (1500 and 9000) as the buffers (2048
and 9216 in size) happened to have enough spare room. I ran into it when
playing around with unusual MTUs.
MFC after: 2 weeks
re-used by the upcoming EDMA TX completion code.
Make ath_stoptxdma() public, again so the EDMA TX code can use it.
Don't check for the TXQ bitmap in the ISR when doing EDMA work as it
doesn't apply for EDMA.
make maintaining this driver from the documentation easier in the future.
This is a mostly mechanical change.
In uslcom_param(), move the zeroing of the final two fields of the
flowctrl structure outside of the "if CRTSCTS" section - not only were
they being zeroed in both the clauses, but these two fields have nothing
to do with hardware flow control anyway.
values).
- cong_drop specifies what to do on congestion: nothing, backpressure,
or drop.
- fl_pktshift specifies the padding before Ethernet payload.
- fl_pad specifies the boundary upto which to pad Ethernet payload.
- spg_len controls the length of the status page.
MFC after: 2 weeks
Trying to up the reference from the load loop risks missing dependencies
that have not been loaded yet.
MFC afer: 1 week
Reported by: nox
Reviewd by: kib
reason for generated trap. The dump of basic signal information and 8
bytes of the faulting instruction are printed on the controlling
terminal of the process, if the machdep.uprintf_signal syscal is
enabled.
The print is the only practical way to debug traps from a.out
processes I am aware of. Because I have to reimplement it each time I
debug an issue with a.out support on amd64, commit the hack to main
tree.
MFC after: 1 week
in long mode which transfers control to 32bit code segment. Unbreak
the lcall $7,$0 implementation on amd64 by putting the 64bit user code
segment' selector into call gate, and execute the 64bit trampoline
which converts the return frame into 32bit format and switches back to
32bit mode for executing int $0x80 trampoline.
Note that all jumps over the hoops are performed in the user mode.
MFC after: 1 week
PROT_EXEC if prot is non-zero, process is 32bit and
kern.elf32.i386_read_exec syscal is enabled. This workaround is needed
for old i386 a.out binaries, where dynamic linker did not specified
PROT_EXEC for mapping of the text.
The kern.elf32.i386_read_exec MIB name looks weird for a.out binaries,
but I reused the existing knob which already has the needed semantic.
MFC after: 1 week
mappings for a.out binaries. Apparently, a.out ld.so from FreeBSD
1.1.5.1 can issue such requests.
Reported and tested by: Dan Plassche <dplassche@gmail.com>
MFC after: 1 week
network file systems (not only NFS proper). Short reads cause pages
other then the requested one, which were not filled by read response,
to stay invalid.
Change the vm_page_readahead_finish() interface to not take the error
code, but instead to make a decision to free or to (de)activate the
page only by its validity. As result, not requested invalid pages are
freed even if the read RPC indicated success.
Noted and reviewed by: alc
MFC after: 1 week
