- correct format strings
- fill opt_agp.h if AGP_DEBUG is defined
- bring AGP_DEBUG to LINT by mentioning it in NOTES
This should hopefully fix a warning that was...
Found by: Coverity Prevent(tm)
CID: 3676
Tested on: amd64, i386
Note that you need at least xf86-video-intel 2.4.3 for this to work.
The G4X doesn't put the GATT into the same area of stolen memory
as all the other chips and older versions of the driver didn't
handle that properly.
Tested by: ganbold
Approved by: kib
MFC after: 2 weeks
g33 based chips use a different method of identifying the gtt size.
g45 based chips gtt is located in a different area of stolen memory.
Approved by: jhb (mentor)
MFC after: 2 weeks
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.
Reviewed by: kib
to flush the TLB instead of hardcoding a size of 33 pages. Apertures of
32MB and 64MB only use a 16 page GATT and an aperture of 128MB only uses
a 32 page GATT, so without this the code could walk off the end of the
pointer and cause a page fault if the next page was unmapped. Also, for
aperture sizes > 128MB, not all of the pages would be read. The Linux
driver has the same bug.
MFC after: 1 week
Tested by: Frédéric PRACA frederic.praca of freebsd-fr.org
bumped to 800004 to note the change though userland apps should not be
affected since they use <sys/agpio.h> rather than the headers in
sys/dev/agp.
Discussed with: anholt
Repocopy by: simon
/dev/agpgart and agp_free_res() frees resources like the BAR for the
aperture. Splitting this up lets chipset-specific detach routines
manipulate the aperture during their detach routines without panicing.
MFC after: 1 week
Reviewed by: anholt
This adds a function to agp.c to set the aperture resource ID if it's
not the usual AGP_APBASE. Previously, agp.c had been assuming
AGP_APBASE, which resulted in incorrect agp_info, and contortions by
agp_i810.c to work around it.
This also adds functions to agp.c for default AGP_GET_APERTURE() and
AGP_SET_APERTURE(), which return the aperture resource size and disallow
aperture size changes. Moving to these for our AGP drivers will likely
result in stability improvements. This should fix 855-class aperture
size detection.
Additionally, refuse to attach agp_i810 when some RAM is above 4GB and
the GART can't reference memory that high. This should be very rare.
The correct solution would be bus_dma conversion for agp, which is
beyond the scope of this change. Other AGP drivers could likely use
this change as well.
G33/Q35/Q33 AGP support is also included, but disconnected by default
due to lack of testing.
PR: kern/109724 (855 aperture issue)
Submitted by: FUJIMOTO Kou<fujimoto@j.dendai.ac.jp>
Approved by: re (hrs)
- Rename confusing AGP_INTEL_I845_MCHCFG to AGP_INTEL_I845_AGPM.
- Move E7205 and E7505 from i8x5 to i8x0 family. It probably worked
because the actual offset is the same.
In fact, all three families have the bit at the exact same place. Only
differences are name and width of the registers, i.e., NBXCFG (0x50, dword),
RDCR (0x51, byte), AGPM (0x51, byte), MCHCFG (0x50, word) depending on
the family of the chipsets.
The key problem was that the aperture size detection using the MSAC bit
doesn't work -- the bit appears to be set even when it shouldn't be. Linux
takes a different approach, testing for a bit of the GMADR (PCIR_BAR(2)) being
set. However, as I don't think that's a safe way to test aperture size, we
just allocate the resource and check its size. This also pointed out that
agp_generic_attach hadn't been allocating our aperture resource, which may
have caused problems in some cases.
Also corrected is a minor copy-and-pasteo in an error case.
PR: kern/103079
Submitted by: mnag
Tested on: i945GM, i915GM
MFC after: 2 weeks
misc. control registers correctly and it is inconsistent with north bridge.
In fact, there are too many broken BIOS implementations out there and we
cannot fix every possible combination but at least it is consistent with
what we advertise with ioctl(2).
capability is present as not all devices supported by the agp_i810 driver
(such as i915) have the AGP capability. Instead, add an identify routine
to the agp_i810 driver that uses the PCI ID to determine if it should
create an agp child device.
the addition of pci_find_extcap().
- Change the drm drivers to attach to vgapci. This is #ifdef'd so the
code can be shared across branches.
- Use pci_find_extcap() to look for AGP and PCIE capabilities in drm.
- GC all the drmsub stuff for i810/i830/i915. The agp and drm devices are
now both children of vgapci.
attach to the hostb driver instead. This means that agp can now be loaded
at runtime (in theory at least). Also, the drivers no longer have to
explicity call device_verbose() to cancel out any earlier calls to
device_quiet() by the hostb(4) driver (this shows a limitation in new-bus,
drivers really shouldn't be doing device_quiet() until they know they are
going to drive that device, i.e. in attach).
