TIOCMSET before FreeBSD existed and have never been implemented by any
FreeBSD serial driver (not even as aliases).
Moved the TIOCM bit definitions to be with TIOCMGET.
Added more comments gaps between ioctl numbers. There are now a large
number of conflicts with ppp, slip, tap and tun ioctls (especially ppp
ones) from closing gaps that weren't there. This mainly breaks decoding
of ioctl numbers in kdump, but there are some serious conflicts where
the interpretation of a tty ioctl depends on the line discipline.
aic79xx.seq:
Convert the COMPLETE_DMA_SCB list to an "stailq". This allows us to
safely keep the SCB that is currently being DMA'ed back the host on
the head of the list while processing completions off of the bus. The
newly completed SCBs are appended to the tail of the queue. In the
past, we just dequeued the SCB that was in flight from the list, but
this could result in a lost completion should the host perform certain
types of error recovery that must cancel all in-flight SCB DMA operations.
Switch from using a 16bit completion entry, holding just the tag and the
completion valid bit, to a 64bit completion entry that also contains a
"status packet valid" indicator. This solves two problems:
o The SCB DMA engine on at least Rev B. silicon does not properly deal
with a PCI disconnect that occurs at a non-64bit aligned offset in the
chips "source buffer". When the transfer is resumed, the DMA engine
continues at the correct offset, but may wrap to the head of the buffer
causing duplicate completions to be reported to the host. By using a
completion buffer in host memory that is 64bit aligned and using 64bit
completion entries, such disconnects should only occur at aligned addresses.
This assumes that the host bridge will only disconnect on cache-line
boundaries and that cache-lines are multpiles of 64bits.
o By embedding the status information in the completion entry we can avoid
an extra memory reference to the HSCB for commands that complete without
error.
Use the comparison of a "host freeze count" and a "sequencer freeze count"
to allow the host to process most SCBs that complete with non-zero status
without having to clear critical sections. Instead the host can just pause the
sequencer, performs any necessary cleanup in the waiting for selection list,
increments its freeze count on the controller, and unpauses. This is only
possible because the sequencer defers completions of SCBs with bad status
until after all pending selections have completed. The sequencer then avoids
referencing any data structures the host may touch during completion of the
SCB until the freeze counts match.
aic79xx.c:
Change the strategy for allocating our sentinal HSCB for the QINFIFO. In
the past, this allocation was tacked onto the QOUTFIFO allocation. Now that
the qoutfifo has grown to accomodate larger completion entries, the old
approach will result in a 64byte allocation that costs an extra page of
coherent memory. We now do this extra allocation via ahd_alloc_scbs()
where the "unused space" can be used to allocate "normal" HSCBs.
In our packetized busfree handler, use the ENSELO bit to differentiate
between packetized and non-packetized unexpected busfree events that
occur just after selection, but before the sequencer has had the oportunity
to service the selection.
When cleaning out the waiting for selection list, use the SCSI mode
instead of the command channel mode. The SCB pointer in the command
channel mode may be referenced by the SCB dma engine even while the
sequencer is paused, whereas the SCSI mode SCB pointer is only accessed
by the sequencer.
Print the "complete on qfreeze" sequencer SCB completion list in
ahd_dump_card_state(). This list holds all SCB completions that are deferred
until a pending select-out qfreeze event has taken effect.
aic79xx.h:
Add definitions and structures to handle the new SCB completion scheme.
Add a controller flag that indicates if the controller is in HostRAID
mode.
aic79xx.reg:
Remove macros used for toggling from one data fifo mode to the other.
They have not been in use for some time.
Add scratch ram fields for our new qfreeze count scheme, converting
the complete dma list into an "stailq", and providing for the "complete
on qfreeze" SCB completion list. Some other fields were moved to retain
proper field alignment (alignment >= field size in bytes).
aic79xx.seq:
Add code to our idle loop to:
o Process deferred completions once a qfreeze event has taken full
effect.
o Thaw the queue once the sequencer and host qfreeze counts match.
Generate 64bit completion entries passing the SCB_SGPTR field as the
"good status" indicator. The first bit in this field is only set if
we have a valid status packet to send to the host.
Convert the COMPLETE_DMA_SCB list to an "stailq".
When using "setjmp" to register an idle loop handler, do not combine
the "ret" with the block move to pop the stack address in the same
instruction. At least on the A, this results in a return to the setjmp
caller, not to the new address at the top of the stack. Since we want
the latter (we want the newly registered handler to only be invoked from
the idle loop), we must use a separate ret instruction.
Add a few missing critical sections.
Close a race condition that can occur on Rev A. silicon. If both FIFOs
happen to be allocated before the sequencer has a chance to service the
FIFO that was allocated first, we must take special care to service the
FIFO that is not active on the SCSI bus first. This guarantees that a
FIFO will be freed to handle any snapshot requests for the FIFO that is
still on the bus. Chosing the incorrect FIFO will result in deadlock.
Update comments.
aic79xx_inline.h
Correct the offset calculation for the syncing of our qoutfifo.
Update ahd_check_cmdcmpltqueues() for the larger completion entries.
aic79xx_pci.c:
Attach to HostRAID controllers by default. In the future I may add a
sysctl to modify the behavior, but since FreeBSD does not have any
HostRAID drivers, failing to attach just results in more email and
bug reports for the author.
MFC After: 1week
CFLAGS in all cases, but POSIX requires a default of -O. Adding
-pipe unconditionally still is still broken for non-gcc compilers
in the non-POSIX case.
namespace pollution in other headers. <sys/types.h> is now the only
prerequisite for <sys/sx.h>.
Fixed some style bugs:
- removed bogus LOCORE ifdef. Including this C header in assembler
sources is just nonsense.
- removed unused include of <sys/_mutex.h>. It finished rotting when
the mutex in struct sx became indirect in rev.1.15.
- removed most comments on #else and #endif's and cleaned up the others.
All were misindented...
- add an option for the output device in the hope that this can
be made non-blocking at some stage.
- define an alias for the disk device, required by dev/ofw/ofw_disk.c
- shift iobus to 0x9000000 so as not to clash with the OpenFirmware
entry point of 0x8000400 when address decoding.
- down-tone comments about the disk dev config :-)
using the direct-mapping of physmem to force PTE data structures
to be physically addressable so the interrupt-time real-mode
DSI trap handler could perform PTE spills. However, the memory
may have been > 256Mb, which would have caused a BAT spill and
double-interrupt.
The new trap code no longer handles PTE spills, so the requirement
that these pages be direct-mapped no longer applies. The irony is
UMA_MD_SMALL_ALLOC will return direct mappings for these structs :-)
- remove unused 601 and tlb exception code
- remove interrupt-time PTE spill code. The pmap code
will now take care of pinning kernel PTEs, and there
are no longer issues about physical mapping of PTE
data structures
- All segment registers are switched on kernel entry/exit,
allowing the kernel to have more virtual space and for
user virtual space to extend to 4G.
- The temporary register save area has been shifted from
unused exception vector space to the per-cpu data area.
This allows interrupts to be delivered to multiple CPUs
- ISI traps no longer spill to BAT tables. It is assumed
that all of kernel instruction memory is pinned.
- shift from 'ldmw/stmw' instructions to individual register
loads/stores when saving context. All PPC manuals indicate
this should be much faster.
- use '%r' for register names throughout.
TODO: need to test if DSI traps were the result of kernel stack
guard-page hits.
Reworked from: NetBSD
PS. There is a inconsistency in this manual page, because in
non-WITNESS case sx_assert(9) does not panics, it only prints
the warning. I haven't fixed this, because jhb@ is planing to
replace those printf()s with panic()s.
Reviewed by: jhb
Approved by: jhb, scottl (mentor)
- Rename temporary variable names ("tmp", "tmp2") to more informative
names ("load", "pctcpu", "rss", ...)
- Unclutter indentation and return paths: rather than lots of nested
ifs, simply return earlier if it's not going to work out. Simplify
general structure and avoid "deep" code.
- Comment on the thread/process selection and locking.
- Correct handling of "running"/"runnable" states, avoid "unknown"
that people were seeing for running processes. This was due to
a misunderstanding of the more complex state machine / inhibitors
behavior of KSE.
- Do perform ttyinfo() printing on KSE (P_SA) processes, it seems
generally to work.
While I initially attempted to formulate this as two commits (one
layout, the other content), I concluded that the layout changes were
really structural changes.
Many elements submitted by: bde
Since we have a worker thread now, we can actually do the allocation
asynchronously in that thread's context. Also, we need to return a
status value: if we're unable to queue up the async allocation, we
return NDIS_STATUS_FAILURE, otherwise we return NDIS_STATUS_PENDING
to indicate the allocation has been queued and will occur later.
This replaces the kludge where we just invoked the callback routine
right away in the current context.
reorganize the printing of the interface name when using wildcard
cloning so it is not printed if it we either immediately rename or
destroy the interface.
Reviewed by: ru
The basic process is to send a routing socket announcement that the
interface has departed, change if_xname, update the sockaddr_dl
associated with the interface, and announce the arrival of the interface
on the routing socket.
As part of this change, ifunit() is greatly simplified by testing
if_xname directly. if_clone_destroy() now uses if_dname to look up the
cloner for the interface and if_dunit to identify the unit number.
Reviewed by: ru, sam (concept)
Vincent Jardin <vjardin AT free.fr>
Max Laier <max AT love2party.net>
- Use the regular forth scripts including the stock device.hints file on
the boot floppies.
- gzip all the various text files on the boot floppy that are larger than
one sector to save on space.
- Generate a loader.conf to load the kernel, acpi.ko, and mfsroot making
use of the 'module_before' variables to prompt for a floppy to be entered
when required and use a stock loader.rc. This enables the beastie menu
on i386.
- PC98 has been changed to split the mfsroot for now so that the floppies
fit. When the PC98 bootstrap is updated to work with ELF files (which
needs to happen anyway), then SPLIT_MFSROOT can be turned off for PC98.
