pcib_alloc_msix() methods instead of using the method from the generic
PCI-PCI bridge driver as the PCI-PCI methods will be gaining some PCI-PCI
specific logic soon.
for printing/logging ipv6 addresses.
The caller now has to hand in a sufficiently large buffer as first
argument.
This is the "+ one more change" missed in the original commit.
Noticed by: tinderbox
Pointy hat to: me (#1)
In ip6_sprintf no longer use and return one of eight static buffers
for printing/logging ipv6 addresses.
The caller now has to hand in a sufficiently large buffer as first
argument.
- Use the appropriate register writing method when reseting the chip
- Program the descriptor DMA engine correctly.
- More reliably detect certain chips and their features.
Also add some low-level debugging tools to help future work on this driver.
Submitted by: David Christenson (proof of concept changes)
Sponsored by: www.UIA.net
_thr_ucond_broadcast, clear condition variable pointer in cancellation
info after returing from _thr_ucond_wait, since kernel has already
dropped the internal lock, so we don't need to unlock it in cancellation
handler again.
This is easy to reproduce for EROFS. I am not sure if the attrs can be corrupt
for other NFS error responses. For now, disabling wcc pre-op attr checks and
post-op attr loads on NFS errors (sysctl'ed).
Reported by: Kris Kennaway
- Correct RX packet drop counter for BCM5705+. This register is read/clear
and it wraps very quickly under heavy packet drops because only the lower
ten bits are valid according to the documentation. However, it seems few
more bits are actually valid and the rest bits are always zeros[1].
Therefore, we don't mask them off here. To get accurate packet drop count,
we need to check the register from bge_rxeof(). It is commented out for now,
not to penalize normal operation. Actual performance impact should be
measured later.
- Correct integer casting from u_long to uint32_t. Casting is not really
needed for all supported platforms but we better do this correctly[2].
Tested by: bde[1]
Suggested by: bde[2]
o Remove unused static global variable e1000phy_debug.
o Take advantage of mii_phy_dev_probe().
o Use MII_ANEGTICKS/MII_ANEGTICKS_GIGE instead of magic number 5.
o Add IFM_NONE as e1000phy(4) supports it without issues.
o Nuke magic PHY programming sequence in PHY reset and follow correct
reset sequence. [1]
o Make manual media selection work for all supported media types.
o Don't set MIIF_NOISOLATE so e1000phy(4) can be used in
configurations with multiple PHYs.
o In 1000baseT, when setting the link manually, one side must be the
master and the other the slave. If LINK0 is set, program the PHY
to be a master, otherwise it's a slave.
o When we lost a link, reset mii_ticks immediately so it correctly
check number of seconds elapsed in autonegotiation phase.
o Announce link loss right after it happens.
o After kicking autonegotiation, report PHY status instead of
returning immediatly.
o When link state check is in progress, check auto negotiation
completion bit only when auto negotiation is enbaled.
o When PHY is resolved to a master, show it with IFM_FLAG2.
Special thanks to marius who fixed several nits in original patch.
In half-duplex mode, nfe(4) fails to send packets. I think it's a bug
in nfe(4) as the same PHY works without problems on msk(4).
Obtained from: em(4) [1]
Reviewed by: marius
Tested by: bz
Fixing the IP accounting issue, if we plan to do so, needs to be better
thought out; the 'fix' introduces a hash lookup and a possible kernel panic.
Reported by: Mark Tinguely
