power x 0.
pccardc power x 0 used to disable the slot. But a suspend/resume
would reactivate the pccard. It no longer does that. Now the
disabling of the slot is sticy until it is reset with power x 1 or the
card is ejected. This seems closer to correct behavior to me.
o Process all card state changes the same using pccard_do_stat_change().
o Cleanup disabling the card so that we can preserve the state after
the change. Basically, don't set it to empty as often as we do.
o On suspend, the new state is "empty" and the laststate is "suspend"
o Document state machine with a diagram of states and edges. The
edges are labeld to tell the reader what event causes the external
state changes.
o "machdep.pccard.pcic_resume_reset" may be obsolete now. We always
call the bridge driver's resume method on resume now. Otherwise cards
won't automatically show up. If it needs to stay, I'll add it back.
Frist, for pci slots, make the setup intr save the requested interrupt
vector and arg and return rather than passing it up to our parent. On
interrupts, we call this vector iff there's a card in the slot. This
should eliminate some of the hangs or "weird" messages that people see
when ejecting cards and also help close the race window somewhat.
Reading the pci bus one more time for this information is judged to be
an acceptible tradeoff since it is very very fast.
Cleanup a little how we detect unsupported cards. Only detect
unsupported cards (eg cardbus cards) on card insertion (or more
pedantically when a card is actually present). This should allow us
to change the message in the future to "cardbus card not supported
with OLDCARD" :-).
Note:
We may also consider this for the ISA bus case, but there the
reads are much more expensive and the location of the CD pin
status lines appears to be less standardized. Also, the ISA
management interrupt isn't shared with the card's interrupt.
The mutliplex the CSC and function interrupts bit also appears
to be non-standard (or at least not imlemented on all
bridges).
for card change interrupts is different than the pci stuff that's
coming soon. Set the management irq in different ways. If
pci_parallel interrutp routing, then use the PCI way of getting
interrupts. Move polling mode into pcic_isa since when we're routing
via pci polling doesn't work because many bridges (systems hang solid).
If we're routing interrupts via pci, they can be shared, so flag them
as such.
Note, this doesn't actually change anything since the pci attachment
isn't quite ready to be committed.
csc_route and func_route to hold the way that each interrupt is
routed. csc is Card Status Change in the datasheets and standard, but
is called "Management Interrupt" in FreeBSDese. There are three types
of interrupt routing: ISA parallel, PCI parallel and ISA serial (some
chipsets support other types as well, but I don't plan on supporting
them).
When we try to allocate an interrupt, and the type for that interrupt
is pci_parallel, allow it to be shared by oring in RF_SHAREABLE to the
flags argument. Introduce pcic_alloc_resource to allow this to
happen.
interrupts on other buses. Right now it isn't used, but will be for
the pci attachment.
# Add copyright by me for this year since I've changed so much.
pcic_{get,put}b_io. There are some pci bridges (the CL-PD6729 and
maybe others) that do not have memory mapped registers, so we'll need
these in both places. Declare them in pcicvar.h.
have a slightly different 3.3V support than the other clones, so
compensate as best we can. Note: 3.3V support is untested since I do
not have any 3.3V cards that I know of to test it with.
Work through the various power commands and convert them from a "is
this a foo controller or a foo' controller or a foo''' controller" to
a cabability based scheme. We have bits in the softc that tell us
what kind of power control scheme the controller uses, rather than
relying on being able to enumerate them all. Cardbus bridges are
numerous, but nearly all implement the i82365sl-DF scheme (well, a few
implement cirrus CL-PD67xx, but those were made by Cirrus Logic!).
Add a pointer back to the softc in each pcic_slot so we can access
these flags.
Add comments that talk about the issues here. Also note in passing
that there are two differ Vpp schemes in use and that we may need to
adjust the code to deal with both of them. Note why it usually works
now.
We have 5 power management modes right now: KING, AB, DF, PD and VG.
AB is for the i82365 stpes A, B and C. DF is for step DF. PD is the
cirrus logic extensions for 3.3V while VG is the VADEM extensions for
3.3V. KING is for the IBM KING controller found on some old cards.
# I'm looking for one of those old cards or a laptop that has the KING
# bridge in it.
We have to still cheat and treat the AB parts like the DF parts
because pci isn't here yet. As far as I can tell, this is harmless
for actual old parts and necessary to work with 3.3V cards in some
laptops.
This almost eliminates all tests for controller in the code. There
are still a few unrelated to power that need taming as well.
o Introduce flags word to the softc. This will be used to control various
aspects of the driver. Right now there are two bits defined, PCIC_IO_MAPPED
and PCIC_MEM_MAPPED. One for ISA cards that are I/O mapped, the other is
for PCI cards that are memory mapped. Only the ISA side is implemented
with this commit.
o Introduce a pcic_dealloc which will cleanly dealloc resources used. Right
now it is only supported when called from probe/attach.
o Keep track of resources allocated in the pcic_softc.
o move pcictimeout_ch to the softc so we can support multiple devices
in polling mode.
o In ISA probe, set PCIC_IO_MAPPED.
o Introduce and compute the slot mask. This will be used later when
we expand the number of slots on ISA from 2 to 4. In such a case, we
appear to have to use polling mode otherwise we get two different cards
trying to drive the same interrupt line. I don't have hardware to
test this configuration, so I'll stop here.
soon attach directly to pcic rather than the kludge pci-pcic device we
have now.
In some ways, this is similar to the work PAO3 did to try to support
cardbus bridges. In some ways different. This and future commits
will be taking from the spirit of many of those changes. pcicvar.h is
completely different from the pcicvar.h that appeared in PAO3, but
similar in concept.
