released management apps.
1. Implement poll(). This will check for queued aif's so that a
subsequent ioctl call to retrieve the next aif will not block.
2. Don't catch signals when sleeping on a fib sent from userland. This
causes a race and panic due to the pthread context switcher waking
up the tsleep at inopportune times.
3. Fix some whitespace nits.
MFC after: 3 days
- set sc->acpi_s4bios to 1 by default for hibernation until
OS-initiated S4 transition is implemented.
- change the behavior of acpi_sleep_state_sysctl() if new value is
the same as old one, do nothing instead of EINVAL.
mbuf allocation fails, and fix (i hope) a couple of style bugs.
I believe these printf() are extremely dangerous because now they can
occur on every incoming packet and are not rate limited. They were
meant to warn the sysadmin about lack of resources, but now they
can become a nice way to panic your system under load.
Other drivers (e.g. the fxp driver) have nothing like this.
There is a pending discussion on putting this kind of warnings
elsewhere, and I hope we can fix this soon.
underlying unaligned bcopy) on incoming packets that are already
available (albeit unaligned) in a buffer.
The performance improvement varies, depending on CPU and memory
speed, but can be quite large especially on slow CPUs. I have seen
over 50% increase on forwarding speed on the sis driver for the
486/133 (embedded systems), which does exactly the same thing.
The behaviour is controlled by a sysctl variable, hw.dc_quick which
defaults to 1. Set it to 0 to restore the old behaviour.
After running a few experiments (in userland, though) I am convinced
that doing the m_devget() is detrimental to performance in almost
all cases.
Even if your CPU has degraded performance with misaligned data,
the bcopy() in the driver has the same overhead due to misaligment
as the one that you save in the uiomove(), plus you do one extra
copy and pollute the cache.
But more often than not, you do not even have to touch the payload,
e.g. when you are forwarding packets, and even in the often-cited
case of NFS, you often end up passing a pointer to the payload to
the disk controller.
In any case, you can play with the sysctl variable to toggle between
the two behaviours, and see if it makes a difference.
MFC-after: 3 days
allows us to move the sio softc data structure back into sio.c and
reduce the complexity of the non sio.c sio files.
Submitted by: bde
# I didn't fix the locking issues that bruce also submitted.
loader parameter. This allows us to more easily boot on big memory
configuration machines. hw.pccbb.start_mem. Reflect this in a sysctl
so we can read it from userland.
# Note: we need a TUNABLE_ULONG to do this right. I'll add that to
# kernel.h soon.
request to one that's supported by the bridge. I'm not 100% sure this
is correct, but it makes it easier for the cardbus bridge to allocate
its memory.
Similar code is needed for the I/O range. Also, I'm not sure if I
should be doing this based on memory or pmemory (but likely should do
it based on some flag that tells us to prefetch or not).
Talked about a long time ago with: msmith
NEWCARD. Other patches may be reqiured to sio to prevent a hang on
eject. Also add commented out entries for sio_pccard.c in files.pc98
to match other architectures.
Submitted by: yamamoto shigeru-san
changing. Also change it from 0x44000000 to 0x84000000 for large memory
machines.
# the PCI bus code should do this for us. This is a bandaide, not a
# solution.
click) do not include newline into the buffer. This is exacly how
things worked before my recent changes to the cut'n'paste code and
how they work in 4-STABLE.
card is ejected while we're in this routine.
yamamoto-san's original patch had a small race window for AX88190
chips, which I corrected by limiting the number of iterations we'd try
to reset the bits to be about 15ms rather than forever. This seems to
work for me, but I don't have a large collections of cards based on
this chipset.
Submitted by: YAMAMOTO Shigeru
snooped on. This causes all kinds of Bad Things(tm) to happen since
closing one session will clobber state that's needed for the other
one. This could theoretically be supported if the code was careful,
but until somebody implements that, preventing this will stop people
from unknowingly shooting themselves in the foot.
device cloned, and assign all further devices to depend on it. This
allows us to call dev_depends() on it at module unload time to get rid
of /dev/snp* (in the devfs case, anyway). For this to work, we must
not destroy the device at close time. [Idea stolen from if_tun.]
The above has the following sideaffects: (a) The snp device used by
watch(8) will remain after watch(8) exits. This is probably how it
should have been all along, and how it was before devfs came along.
(b) Module unload doesn't panic if there are any /dev/snp* devices
which haven't been used (and thus previously destroyed). Thus, we can
reenable the unload functionality disabled in rev. 1.65.
PR: 32012
MFC after:3 days
- Add memory barrier definition for sparc64.
Patch sent by David E. O'Brien, approved by maintainer.
- Fix an endianization error of a bus physical address used from SCRIPTS
that made the driver fail on big endian machines as sparc64.
signature, but otherwise behaves just like a normal USB mass-storage
device. Add a new quirk to cover this case, and enable it for C-1
cameras. The quirk enables translation from the C-1 signature to
the normal CSWSIGNATURE value.
Reviewed by: n_hibma
Actually this porting supports Pegasus II chip so I guess some other
devices supported by NetBSD also work. But the devices list are not
included because I cannot confirm if they work.
Obtained from: NetBSD
MFC after: 3 weeks
2. Add OF_getprop_alloc(), a helper function that will malloc() a sufficient
amount of memory and then retrieve a property value into it.
Approved by: benno
Obtained from: NetBSD (1)
disabled unless verbose flag is set. Also fix some messages in terms
of English.
The critical messages and error messages in probe/attach routine are
unchanged by this commit.
Now you can say;
# sysctl hw.acpi.lid_switch_state=NONE
instead of specifying unsupported _Sx object in the system.
Actually, S4B is going to disappear in ACPICA and we already have
hw.acpi.s4bios to distinguish BIOS hibernation or OS hibernation.
pccard layer and rename them PCMCIA_CARD and PCMCIA_CARD2 respectively
(note, this is being done with an eye towards NetBSD integreation so
it is easier to keep lists of cards between us and them in sync).
Use this in the an and wi drivers.
trying something new with the macros here and will likely try to get
them adopted by NetBSD as well as moving them to other drivers. They
make the list more compact and easier to read, the price of rigid to a
schema for generating them (of course there are those that would argue
this isn't bad).
Obtained from: NetBSD's if_wi_pcmcia.c 1.9
off chip that was on one prototype board. However, this appears to be
a design that many chipsets are compatible with its PPEC register set
(eg the Omega 82c094). Through the kindness of the Red Hat developer
David Woodhouse, I now have this datasheet.
I may take the advise of one of the bsd-nomads (whose name
unfortunately escapes me at the moment) and split out all these 16-bit
I/O mapped PCI devices into a separate driver...
that it has one BAR that's mapped to 0x3e0 and is I/O only. It does
not conform to the Yenta spec, like other PCI PCMICA bridges do (eg
the TI 1031, which is mostly a 1131 w/o 32bit card support). It
appears that this chip may also need to not route PCI interrupts
as well.
This chip is used in the NEC Versa 2430CD (and it appears that
sometimes it works, while other times it doesn't) and others in the
2400 series. While the NEC website claims Cardbus support, I can't figure
out how that is possible.
Submitted by: Ben Timby <ben@webexc.com>
- Add S4BIOS sleep implementation. This will works well if MIB
hw.acpi.s4bios is set (and of course BIOS supports it and hibernation
is enabled correctly).
- Add DSDT overriding support which is submitted by takawata originally.
If loader tunable acpi_dsdt_load="YES" and DSDT file is set to
acpi_dsdt_name (default DSDT file name is /boot/acpi_dsdt.aml),
ACPI CA core loads DSDT from given file rather than BIOS memory block.
DSDT file can be generated by iasl in ports/devel/acpicatools/.
- Add new files so that we can add our proposed additional code to Intel
ACPI CA into these files temporary. They will be removed when
similar code is added into ACPI CA officially.
conf/files) and as a result appears to have been missed in the bulk
KSE update of drivers. This change replaces references to proc
with thread. It has not been compile-tested.
in wdrain during a write. This flag needs to be used in devices whos
strategy routines turn-around and issue another high level I/O, such as
when MD turns around and issues a VOP_WRITE to vnode backing store, in order
to avoid deadlocking the dirty buffer draining code.
Remove a vprintf() warning from MD when the backing vnode is found to be
in-use. The syncer of buf_daemon could be flushing the backing vnode at
the time of an MD operation so the warning is not correct.
MFC after: 1 week
be set to 1 to make FreeBSD and Tru64 coexist peacefully on a dual
boot system and not clobber each other's year in the TOY clock.
(Tru64 uses an offset 52 years higher than one would expect)
Obtained from: NetBSD
MFC After: 1 week
- Now that apm loadable module can inform its existence to other kernel
components (e.g. i386/isa/clock.c:startrtclock()'s TCS hack).
- Exchange priority of SI_SUB_CPU and SI_SUB_KLD for above purpose.
- Add simple arbitration mechanism for APM vs. ACPI. This prevents
the kernel enables both of them.
- Remove obsolete `#ifdef DEV_APM' related code.
- Add abstracted interface for Powermanagement operations. Public apm(4)
functions, such as apm_suspend(), should be replaced new interfaces.
Currently only power_pm_suspend (successor of apm_suspend) is implemented.
Reviewed by: peter, arch@ and audit@
us a lot on older Alphas.
Andrew Gallatin, Thomas V. Crimi, and Peter Jeremy contributed to this
work along with the submitter.
Submitted by: Andrew M. Miklic <miklic@home.com>
- Add a new MIB for battery info expire time in order to make it changeable.
Battery info expire time can be specified by
hw.acpi.battery.info_expire in sec.
- Add own MALLOC type and fix some potential memory leakages.
- Change some frequent printings to verbose printing.
- Stop timeout during acpi_cmbat_get_bst() too. This should reduce
the races with BIF evaluation.
- Remove acpi_cmbat_get_bif() invocation from acpi_cmbat_attach().
This was redundant because this should be called from
acpi_cmbat_timeout() now.
- Give a guaranteed minimum cooling run time to avoid too frequent
cooling system On/Off switching. The minimum cooling run time can be
specified by hw.acpi.thermal.min_runtime in sec.
- Refine message printing (_AC-1 -> NONE).
- Add verbose mode enable/disable capability by hw.acpi.verbose in bool.
Reviewed by: acpi-jp@ folks
in the 21143, instead of giving priority to the receive unit.
This gives a 10-15% performance improvement in the forwarding rate
under heavy load.
Reviewed-by: Bill Paul
while it is on a queue with the queue lock and remove the per-task locks.
- Remove TASK_DESTROY now that it is no longer needed.
- Go back to inlining TASK_INIT now that it is short again.
Inspired by: dfr
This emulates APM device node interface APIs (mainly ioctl) and
provides APM services for the applications. The goal is to support
most of APM applications without any changes.
Implemented ioctls in this commit are:
- APMIO_SUSPEND (mapped ACPI S3 as default but changable by sysctl)
- APMIO_STANDBY (mapped ACPI S1 as default but changable by sysctl)
- APMIO_GETINFO and APMIO_GETINFO_OLD
- APMIO_GETPWSTATUS
With above, many APM applications which get batteries, ac-line
info. and transition the system into suspend/standby mode (such as
wmapm, xbatt) should work with ACPI enabled kernel (if ACPI works well :-)
Reviewed by: arch@, audit@ and some guys
queue, and a mutex to protect the global list of taskqueues. The only
visible change is that a TASK_DESTROY() macro has been added to mirror
the TASK_INIT() macro to destroy a task before it is free'd.
Submitted by: Andrew Reiter <awr@watson.org>
and packet bundling. Make the microcode settings controllable via sysctl
and loader tunables.
Submitted by: Marko Zec <zec@tel.fer.hr>
(with some munging and dynamic sysctl support by me)
Also extend the workaround for Dynamic Standby mode to later '559 chips,
not just the ICH2 variants.
This is taken verbatim from the Intel's e100-1.6.22 release, with
the addition of their LICENSE file at the top.
Submitted by: Marko Zec <zec@tel.fer.hr>
If we get a completion status of RQCS_QUEUE_FULL, it means
that the internal queues are full. Other QLogic boards set
the QFULL SCSI status. But *nooooooooooo*, not the 2300.
MFC after: 1 day
sio_pccard_detach to use new siodetach. Add an extra arg to sioprobe
to tell driver to probe/not probe the device for IRQs.
This incorporates most of Bruce's review material. I'm at a good
checkpoint, but there will be more to come based on bde's further
reviews.
Reviewed by: bde
This might need additional code for hotswapping use, but first
I need to get my hands on actual hw...
Based on docs kindly provided by Promise Inc which we thank for
the close cooperation with the FreeBSD project!.
avoiding EC read errors on some laptops.
- Stop updating Battery info for all user requests
- Update Battery info by notify events and resume method
- Poll Battery info every one minute
Suggested by: takawata
Move sio from isa/sio.c to dev/sio/sio.c. The next step is to break
out the front end attachments, improve support for these parts on
different busses, and maybe, if we're lucky, merging in pc98 support.
It will also be MI and live in conf/files rather than files.*.
Approved by: bde
Tested with: i386, pc98
tracks as /dev/acdNtY.
This solves the problems with having to deal with howmany and which
devices are open.
For hysterical reasons ONLY, make a link to both the acdNa & acdNc devices.
these chips. There is a new hint, hint.pcm.N.hwvol_config, that can be set
to 1 or 0 to select which pins the buttons are connected to. I'm open to
suggestions on where to document this. Also bump the number of playback
channels up to 4.
MFC after: 3 days
- Count the number of this error.
- When the error is detected for the first time, the psm driver will
throw few data bytes (up to entire packet size) and see if it can
get back to sync.
- If the error still persists, the psm driver disable/enable the mouse
and see if it works.
- If the error still persists and the count goes up to 20,
the psm driver reset and reinitialize the mouse. The counter
is reset to zero.
- It also discards an incomplete data packet when the interval
between two consequtive bytes are longer than pre-defined timeout
(2 seconds). The last byte which arrived late will be regarded as
the first byte of a new packet. This is louie's idea.
You may see the following error logs during the above operations:
"psmintr: delay too long; resetting byte count"
"psmintr: out of sync (%04x != %04x)"
"psmintr: discard a byte (%d)"
"psmintr: re-enable the mouse"
"psmintr: reset the mouse"
MFC after: 1 month
- crhold() returns a reference to the ucred whose refcount it bumps.
- crcopy() now simply copies the credentials from one credential to
another and has no return value.
- a new crshared() primitive is added which returns true if a ucred's
refcount is > 1 and false (0) otherwise.
appropriate cache flush that provides MEMORY_BARRIER in between handoffs
between host && RISC processor for the shared memory request/response
queues.
Submitted by: dfr@nlsystems.com
to see if there's an interrupt (avoids PCI parity errors
which can occur on the 2312 if you access some registers
from the host at the same time the RISC on the 2312 is
C accessing them).
MFC after: 1 day
Fix acpi_DeviceIsPresent to check for valid _STA data and to check
the "present" and "functioning" bits.
Use acpi_DeviceIsPresent in acpi_pcib rather than rolling our own
(also broken) version.
with an ifnet structure (so device_get_softc will get one).
If memory allocation fails in mii_phy_probe, don't just march ahead into
a panic- return ENOMEM.
MFC after: 1 week
per-command component that we *don't* try and pass thru CAM. CAM just
is too risky and too much of a pain- structures get copied, but not
all info of interest can be considered safely transported thru all
consumers (including user space) from the incoming ATIO to the outgoing
CTIO- it's just much safer to have a buddy structure, identified by the
command's tag which *does* make it thru safely.
Pay attention to link speed and report 200MB/s xfer speed for a
23XX card in 2GPs mode.
MFC after: 1 week
built without support for miibus PHYs. Most ed cards don't need
miibus support, so it's useful to be able to avoid the bloat of
all the mii devices for small fixed-purpose kernels.
once so there isn't a window with the ones for the 23XX cards being wrong.
When being verbose, print out some more FC NVRAM values (like framesize).
MFC after: 1 week
. Make internal service routines static.
. Use a consistent ordering of checks in MII_TICK. Do the work in the
mii_phy_tick() subroutine if appropriate.
. Call mii_phy_update() to trigger the callbacks.
ethernet controllers. This adds support for the 3Com 3c996-T, the
SysKonnect SK-9D21 and SK-9D41, and the built-in gigE NICs on
Dell PowerEdge 2550 servers. The latter configuration hauls ass:
preliminary measurements show TCP speeds of over 900Mbps using
only normal size frames.
TCP/IP checksum offload, jumbo frames and VLAN tag insertion/stripping
are supported, as well as interrupt moderation.
Still need to fix autonegotiation support for 1000baseSX NICs, but
beyond that, driver is pretty solid.
sio_lock has been initialized. This prevents the low level console
output (kernel printf) from clobbering the sio settings if the system
happens to be in the middle of comstart().
with weird PCI-PCI bridge configurations to work. Defining
PCI_ALLOW_UNSUPPORTED_IO_RANGE causes the sanity checks to pass even
with out of range values.
Reviewed by: msmith
This fixed the problem on the 3 platforms I've been able to test on.
I'm still of the oppinion that the BIOS should take care of this,
however some board makers only apply this when they spot a
SBLive! soundcard, but the problem exists even without a SBLive!.
This fix should probably go somewhere else, but for now I'll
keep it here since we havn't got a central place to put
such things.
problems currently experienced in -CURRENT.
This should fix the problem that the PS/2 mouse is detected
twice if the acpi module is not loaded on some systems.
we're at least consistent with what tcsendbreak(3) is documented
to do.
MFC after: 2 weeks
Note, the MFC will be to sys/dev/dgb/dgm.c on the RELENG_4 branch
I am not sure if this is absolutely necessary on all systems. Yet,
there certainly are motherboards and notebook systems which require
this, although there are other systems which just don't. I hope we
shall know when to do this on which systems, as the development of our
ACPI subsystem progresses... (I know we didn't need this for the APM
resume.)
ppc to go into EPP mode. These 8 inputs are timestamped in polled
loop so their resolution will be nanoseconds but their granularity
will only be 1/hz.
- SC_CUT_SPACES2TABS - when copying text into the cut buffer convert leading
spaces into the tabs;
- SC_CUT_SEPCHARS="XYZ" - treat supplied characters as possible words
separators when the driver searches for words boundaries when doing cut
operation.
Also unify cut code a bit to decrease amount of duplicated code. This fixes
line cut mode, so that it is no longer pads line with useless spaces.
Approved by: ru
seems to set up memory spaces correctly. This change actually did work for
me using -STABLE, XFree86 4.0.3 ~ some snapshot of DRI awhile back. I sent
mail to dfr to no avail, perhaps someone else would like to test it with
DRI.
Anyway, people have been nagging me about this change for awhile, so here's
the commit.
of the rxeoc handler for now. The rxeoc handler will reset the link,
and the NatSemi chip's RX FIFO will overflow on a 32-bit bus once you
start hitting it with 500Mbps or more of traffic.
Also increase the size of the RX ring to 128 descriptors (was 64).
amdpm(4) and smb(4).
This device can be used with userland programs such as sysutils/lmmon
to retrieve sensor information from the motherboard.
PR: kern/23989
Obtained from: Matthew C. Forman <mcf@dmu.ac.uk>
Based on: alpm(4)
- Add workaround for the problematic PnP BIOS which does not assign
irq resource for the PS/2 mouse device node; if there is no irq
assigned for the PS/2 mouse node, refer to device.hints for an
irq number. If we still don't find an irq number in the hints
database, use a hard-coded value.
- Delete unused ivars.
- Bit of clean up in probe/attach.
- Add PnP ID for the PS/2 mouse port on some IBM ThinkPad models.
them if the device arrives.
This should solve the problem where devices that have been disabled eg. in
the BIOS show up with nonsense resources and hang the bootstrap process.
no longer possible to unload the driver module while sound is playing
(which resulted in a panic).
- Fix a similar problem with the sndstat device that I found while looking
at the above.
- Append a newline character to error messages in pcm_unregister()
Reviewed by: cg
MFC after: 10 days
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
correct mode via ancontrol, you can use bpf to sniff raw 802.11 frames.
Who want's to port AirSnort. ;-)
Submitted by: Doug Ambrisko <ambrisko@ambrisko.com> (author)
David Wolfskill <david@catwhisker.org> (port to current)
Avoid fully initialising the ACPI namespace if we are attempting to avoid
parts of it. This is a workaround for some systems that still crash
the interpreter.
Implement the ISA_IVAR_LOGICALID for ISA compatibility. Implement stubs
for other PnP ID-related ivars.
of the adapter object will always result in a change event.
This fixes the problem where a laptop booted without an AC adapter ran
at 100% CPU speed by default.
Submitted by: "Christopher N . Harrell" <cnh@netvmg.com>
Cirrus Logic PD6834
O2micro OZ6836
O2micro OZ6912/6972
O2micro OZ6922
O2micro OZ6933
TI1260 Note: These two aren't on TI's site, but are in
TI1260B http://www.yourvote.com/pci/vendors.txt
Plus comments for other chips found in Windows INF files, and also
referenced in various spots on the net:
* Intel 82092AA 0x12218086 16bit
* smc/Databook DB87144 0x310610b3
* SMC/databook smc34c90 0xb10610b3
* Omega/Trident 82c094 0x00940123?
* Omega/Trident 82c194 0x01941023
* Omega/Trident 82c722 0x07221023?
* Opti 82c814 0xc8141045
* Opti 82c824 0xc8241045
* NEC uPD66369 0x003e1033
more cleanly and consistently in all APCI, PnP BIOS, and "hint"
cases.
NOTE: this doesn't necessarily solve the problem that the PS/2
mouse is not detected after the recent ACPI update.
SIM (as is true for the 1280 and the 12160), then I have to have separate
flags && status for *both* busses. *Whap*.
Implement condition variables for coordination with some target mode
events. It's nice to use these and not panic in obscure little places
in the kernel like 'propagate_priority' just because we went to sleep
holding a mutex, or some other absurd thing.
Remove some bogus ISP_UNLOCK calls. *Whap*.
No longer require that somebody do a lun enable on the wildcard device
to enable target mode. They are, in fact, orthogonal. A wildcard open
is a statement that somebody upstream is willing to accept commands which
are otherwise unrouteable. Now, for QLogic regular SCSI target mode, this
won't matter for a damn because we'll never see ATIOs for luns we haven't
enabled (are listening for, if you will). But for SCCLUN fibre channel
SCSI, we get all kinds of ATIOs. We can either reflect them back here
with minimal info (which is isp_target.c:isp_endcmd() is for), or the
wildcard device (nominally targbh) can handle them.
Do further checking against firmware attributes to see whether we can,
in fact, support target mode in Fibre Channel. For now, require SCCLUN
f/w to supoprt FC target mode.
This is an awful lot of change, but target mode *still* isn't quite right.
MFC after: 4 weeks
applies to. Do more bus # foo things.
Acknowledge Immediate Notifies right away prior to throwing events upstream
(where they're currently being ignored, *groan*)
Capture ASYNC_LIP_F8 as with ASYNC_LIP_OCCURRED. Don't percolate them
upstream as if they were BUS RESETS- they're not.
and cv_wait for mailbox commands to complete if we start them from
here.
Fix residuals for target mode such that we only check the residual and
set it in the CTIO if this is the last CTIO (when we're sending status).
MFC after: 4 weeks
SIM (as is true for the 1280 and the 12160), then I have to have separate
flags && status for *both* busses. *Whap*.
Implement condition variables for coordination with some target mode
events. It's nice to use these and not panic in obscure little places
in the kernel like 'propagate_priority' just because we went to sleep
holding a mutex, or some other absurd thing.
MFC after: 4 weeks
laptops with this chip should test this and report back as I don't have
access to this hardware myself. People with -stable systems should try
the patch at:
http://www.freebsd.org/~wpaul/conexant.patch.gz
Submitted by: Phil Kernick <Phil@Kernick.org>
luns) firmware for the Fibre Channel cards.
We used to assume that if we didn't download firmware, we couldn't know
what the firmware capability with respect to SCCLUNs is- and it's important
because the lun field changes in the request queue entry based upon which
firmware it is.
At any rate, we *do* get back firmware attributes in mailbox register 6
when we do ABOUT FIRMWARE for all 2200/2300 cards- and for 2100 cards
with at least 1.17.0 firmware. So- we now assume non-SCCLUN behaviour
for 2100 cards with firmware < 1.17.0- and we check the firmware attributes
for other cards (loaded firmware or not).
This also allows us to get rid of the crappy test of isp_maxluns > 16-
we simply can check firmware attributes for SCCLUN behaviour.
This required an 'oops' fix to the outgoing mailbox count field for
ABOUT FIRMWARE for FC cards.
Also- while here, hardwire firmware revisions for loaded code for SBus
cards. Apparently the 1.35 or 1.37 f/w we've been loading into isp1000
just doesn't report firmware revisions out to mailbox regs 1, 2 and 3
like everyone else. Grumble. Not that this fix hardly matters for FreeBSD.
MFC after: 4 weeks
A nsp chip does suspend I/O write by 512bytes burst write,
though the chip only has 48 bytes FIFO. The chip assert I/O WAIT
signal to PC-Card bus after the CPU writes more than 48 bytes to
the chip if the SCSI device does not respond immediately in supsend
I/O burst write. If the device does not respond for a while it might
cause PC-Card bus timeout.
The previous work around was to wait the request from SCSI device.
But there are some devices which request bytes for synchronous transfer
immediately. So current work aound is to fill 32bytes FIFO, wait for
FIFO empty and burst write 512-32 bytes for every 512 bytes block.
Submitted-by: Honda-san (the author of the driver)
Obtained-from: NetBSD/pc98
